OmniView ™ SOHO Series User Manual F1DS102P F1DS104P F1DS102T F1DS104T
Table of Contents Overview Feature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 Equipment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Unit Display Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Installation Pre-Configuration . . . . . . .
Introduction Congratulations on your purchase of a Belkin OmniView KVM switch. Our diverse line of quality KVM solutions exemplifies the Belkin commitment to delivering quality and durability at an affordable price. Engineered to give you control over multiple computers/servers from one console, Belkin KVM switches come in a variety of capacities suitable for all configurations, large or small.
OVERVIEW OVERVIEW The Belkin OmniView SOHO Series KVM Switch allows you to control up to four computers, depending on the model, with one keyboard, monitor, and mouse. All SOHO Series KVM Switches support PS/2 input devices (keyboard and mouse) as well as VGA, SVGA, XGA, and XGAII video. The OmniView SOHO Series KVM Switch you have purchased supports either PS/2 output for computers (F1DS102P or F1DS104P), or both PS/2 and USB output for both USB and PS/2 computers (F1DS102T or F1DS104T).
OVERVIEW Flash Upgrade: Flash upgradeability allows you to obtain the latest firmware upgrades for your KVM Switch. These upgrades will let your KVM Switch continue to be compatible with the latest devices and computers. Firmware upgrades are free for the lifetime of the product. Visit belkin.com for upgrade information and support or see the enclosed instruction document.
OVERVIEW Equipment Requirements Cables: For each PS/2 computer to be connected to the OmniView SOHO Series KVM Switch, one VGA cable, one PS/2 keyboard cable, and one PS/2 mouse cable is necessary. Keyboard and mouse cables must have PS/2 male to PS/2 male connectors. For USB computers, one VGA cable and one USB A-to-B cable is required. To support resolutions of up to 2048x1536@85Hz, use of a 75-Ohm coaxial VGA cable is required to preserve signal integrity.
OVERVIEW Operating Systems OmniView SOHO Series KVM Switches are for use on CPUs using: Platforms: • Windows® 3.x/95/98/2000/Me/NT®/XP • DOS • Linux® • Novell® NetWare® 4.x/5.x Keyboards: • Supports 101-/102-/104-key keyboards Mice: • Microsoft® compatible PS/2 mice with 2, 3, 4, or 5 buttons • Microsoft compatible DB9 serial mice (with use of adapter) Monitor: • VGA • SVGA • MultiSync® Microphone: Multimedia microphone/stereo with 3.5mm connectors Audio: Multimedia speaker/stereo with 3.
OVERVIEW Port status indicator LEDs Removable shroud Manual port selection buttons Base Front View fig.
OVERVIEW 2nd computer USB port–USB 2 2nd computer VGA port–VGA 2 2nd computer audio/microphone jacks 1st computer USB port–USB 1 2nd computer PS/2 mouse/keyboard ports 1st computer audio/microphone jacks 2nd computer PS/2 mouse/keyboard ports 1st computer VGA port–VGA 1 Console audio/ microphone jacks Console PS/2 mouse/keyboard ports DC power jack Console VGA port Back View fig.
OVERVIEW Specifications Part No.: F1DS102P, F1DS104P Part No.
INSTALLATION Pre-Configuration Where to Place the KVM Switch: The compact size of the OmniView SOHO Series KVM Switch makes it perfect for desktop placement. Consider the following when deciding where to place the KVM Switch: whether or not you intend to use the manual push buttons for selecting ports; the length of the cables attached to your keyboard, mouse, and monitor; the location of your CPUs from your console; and the length of the cables you use to connect your computers to the KVM.
INSTALLATION Step-by-Step Installation Guide This section provides complete instructions for the hardware setup of a single SOHO Series KVM Switch. (F1DS102P, F1DS104P, F1DS102T, or F1DS104T) Important Note: Before attempting to connect anything to the SOHO Series KVM Switch or into your computer(s), make sure that everything is powered off. Plugging and unplugging cables while computers are powered on may cause irreversible damage to the computers and KVM Switch.
PS/2 INSTALLATION PS/2 Installation: Keyboard, Video, and Mouse Connections CONNECT THE CONSOLE: 1. Connect the monitor to the SOHO Series KVM Switch. Using the cable that is included with your monitor, connect it to the HDDB15 female port on the top of the SOHO Series KVM Switch with the monitor symbol on the console. See fig. 4. 2. Connect a PS/2 keyboard to the PURPLE port on the console. See fig. 5. 3. Connect a PS/2 mouse to the GREEN port on the console. See fig. 5 fig. 5 11 fig.
PS/2 INSTALLATION CONNECT THE COMPUTER: 4. Connect the first computer’s VGA cable to the SOHO Series KVM Switch. Using the VGA cable (Belkin Part# F3X1105-XX, F3X1835-XX or F2N209-XX), connect the male end of the cable to the VGA port to the computer, and the female end on the VGA port to the top of the SOHO Series KVM Switch labeled CPU1. See fig. 6. fig.
PS/2 INSTALLATION 5. Connect the PS/2 keyboard and PS/2 mouse cables to the appropriate ports on the section labeled CPU1. (Belkin Part# F3X1105-XX, F3X1835-XX, or F2N036-XX). See fig. 7. fig. 7 6. Repeat steps 4 and 5 for each additional computer you wish to connect.
PS/2 INSTALLATION Audio and Microphone Connections are not required to use with your KVM Switch (Recommend Belkin PRO Series Audio Cables Part # F8V209-XX). CONSOLE: 7. Using the audio cable attached to your speakers, connect the male 3.5mm plug to the SPEAKER IN jack on the CONSOLE section of your SOHO Series KVM Switch. See fig. 8. fig.
PS/2 INSTALLATION 8. Using the mic cable attached to your microphone, connect the male 3.5mm plug to the MIC IN jack on the CONSOLE section of your SOHO Series KVM Switch. See fig. 8. COMPUTER: 9. Using the audio cable, connect one end of the male 3.5mm plug to the SPEAKER OUT jack of your sound card or computer and connect the other end to the SPEAKER IN jack of your SOHO Series KVM Switch. See fig. 9. 10. Using a second audio cable, connect one end of the male 3.
USB INSTALLATION USB Installation: Keyboard, Monitor, and Mouse Connections Available on F1DS102T and F1DS104T models only Note: On some computers, you must enable USB support on your system BIOS. Please reference your computer manufacturer's manual or motherboard manual to verify that USB support is enabled. CONSOLE: 1. Connect the monitor to the SOHO Series KVM Switch.
USB INSTALLATION 2. Connect a PS/2 keyboard to the PURPLE port on the CONSOLE. See fig. 11. fig. 11 3. Connect a PS/2-type mouse to the GREEN port on the CONSOLE. See fig. 11. 4. Power on your computer as you would normally and wait until your operating system completes loading.
USB INSTALLATION COMPUTER: 5. Using a standard USB A-to-B cable (we recommend Belkin Part# F3U134-XX or F3U134-XX-GLD), insert the end with the B-type connector to the SOHO Series KVM Switch. Insert the other end of the cable with the A-type connector to an available port on your USB computer or USB hub that is attached to your computer. See fig. 12. 6. Your computer should recognize your KVM Switch and will automatically install the HID USB driver if not already installed on your computer. fig.
USB INSTALLATION Audio and Microphone Connections are not required to use with your KVM Switch. (Recommend to use Belkin PRO Series Audio Cables Part# F8V209-XX) CONSOLE: 7. Using the audio cable attached to your speakers, connect the male 3.5mm plug to the SPEAKER IN on the CONSOLE of your SOHO Series KVM Switch. See fig. 13. fig. 13 8. Using the mic cable attached to your microphone, connect the male 3.5mm plug to the MIC IN on the CONSOLE of your SOHO Series KVM Switch. See fig. 13.
USB INSTALLATION COMPUTER: 9. Using the audio cable, connect one end of the male 3.5mm plug to the SPEAKER OUT jack of your sound card or computer and connect the other end to the SPEAKER IN jack of your SOHO Series KVM Switch. See fig. 14. fig. 14 10. Using a second audio cable, connect one end of the male 3.5mm plug to the MIC OUT jack of your sound card or computer and connect the other end to the MIC IN jack of your OmniView SOHO Series KVM Switch. See fig. 14.
USING YOUR SOHO SERIES KVM SWITCH Powering up the Systems Once all cables have been connected, power up the CPUs that are attached to the SOHO Series KVM Switch. All computers can be powered on simultaneously. The SOHO Series KVM Switch emulates a mouse and keyboard on each port and allows your computer to boot normally. Your Belkin SOHO Series KVM Switch should now be ready for use.
USING YOUR SOHO SERIES KVM SWITCH You can switch directly to any port by entering the PORT number of the port you wish to use. For example, if you press [SCROLL LOCK], [SCROLL LOCK], [2], the computer on port 2 will be selected. Switch to port 4—#4 key Switch to port 2—#2 key AutoScan Mode In AutoScan mode the SOHO Series KVM Switch remains on one port for 10 seconds before switching to the next. This time interval cannot be changed.
BELKIN KVM SWITCHES AND ACCESSORIES OmniView KVM Switches: OmniView E Series. These KVM devices allow you to control two or four computers from one console and make switching between computers more convenient. Designed for compatibility with your PS/2 platform, they reduce desktop clutter and provide a simple, reliable solution at a lower price point.
BELKIN KVM SWITCHES AND ACCESSORIES less cables to hassle with. Other standard features found on this unit include: hot key functionality; keyboard and PS/2 emulations for error-free boot up; and a Belkin Five-Year Warranty. F1DS102P F1DS104P F1DS102T F1DS104T SOHO SOHO SOHO SOHO Series Series Series Series 2-Port 4-Port 2-Port 4-Port PS/2 PS/2 PS/2 PS/2 KVM Switch KVM Switch & USB KVM Switch & USB KVM Switch OmniView PRO Series.
BELKIN KVM SWITCHES AND ACCESSORIES between ports by using hot key commands or push-button port selection. The OmniView MATRIX uses standard cables for easy installation, includes a 12V DC 1A power supply, and is backed by a Belkin One-Year Warranty. F1D208-OSD MATRIX Series 2x8-Port PS/2 KVM Switch OmniView KVM Cables OmniView All-In-One Cable Kits provide you with the quality connections necessary to set up your KVM solution.
BELKIN KVM SWITCHES AND ACCESSORIES PRO Series Plus cables are modestly priced yet built to exacting standards. They receive and transmit data through nickel-plated connectors. The industry-standard 14-pin coaxial VGA cabling was designed to support image clarity for high-resolution applications. The gray jacket bends into the tightest crawl spaces. The PRO Series Plus is available in PS/2- and USB-style cable kits.
BELKIN KVM SWITCHES AND ACCESSORIES F1D090 - The OmniView Mouse Splitter allows you to work with two kinds of PS/2 mice or trackballs without swapping cables or rebooting the computer. F1D201 - The OmniView 2-Port Reverse KVM Switch gives two users central control of one PC from two sets of keyboards, monitors, and mice. F5U119 - The Belkin PS/2-to-USB Adapter converts PS/2 keyboard and mouse signals to USB format.
FAQ SOHO SERIES FAQ SOHO Series Q: What operating systems does the SOHO Series KVM Switch support? A: The SOHO Series KVM Switch will support any operating system that runs on a PS/2 and USB platform. It will also work with nonUSB-enabled Sun and Mac operating systems using the appropriate adapters (Belkin OmniView PS/2 SUN Adapter F1D082, OmniView PS/2 MAC Adapter F1D080). Operating systems include, but are not limited to, DOS, Windows 3.x/95/98/2000/Me/NT/XP, Linux, Mac OS.
FAQ SOHO SERIES Q: How far can the second user be from the SOHO Series KVM Switch? A: When using PS/2 connections, the SOHO Series KVM Switch can be up to 25 feet (7.5m) away from your computer. If your computer needs to be more than 25 feet (7.5m) from the KVM switch, you can use the Belkin CAT5 Extender to extend your PS/2 keyboard, PS/2 mouse, and monitor up to 500 feet (152.4m) away using standard CAT5 UTP cable.
FAQ SOHO SERIES Q: Can PS/2 and USB connections be used simultaneously on the same port? A: No. You must use one or the other per CPU’s dedicated port on the KVM Switch. Q: What are the benefits of the SOHO Series KVM Switch's supporting audio and microphone inputs and outputs? A: The SOHO Series KVM Switch is perfect for the home- and smalloffice user who commonly uses multimedia. With multimedia support you do not need an extra set of speakers for each computer that is connected to your KVM unit.
FAQ SOHO SERIES port (available on the F1DS102T and F1DS104T only). Q: Can I use the SOHO Series KVM Switch to switch video signals only? A: Yes, you may use the SOHO Series KVM Switch to switch between video signals only without having to connect the keyboard and mouse. Keyboard and mouse should be connected directly to the computer that the video signal is taken from to insure that your computer functions properly.
TROUBLESHOOTING A: The SOHO Series KVM Switch comes with a five-year limited warranty. TROUBLESHOOTING VIDEO I am getting ghosting, shadowing, or fuzzy images on my monitor. • Check that all video cables are inserted properly. • Check that the monitor you are using supports the resolution and refresh-rate setting on your computer. • Check that the graphics card you are using supports the resolution and refresh-rate setting on your computer.
TROUBLESHOOTING (F1D065-PWR for your appropriate country). • Connect your monitor directly to the computer to verify that your monitor is functioning properly. KEYBOARD Computer does not detect keyboard and I get a keyboard error reported at boot up. • Check that the keyboard cable between the KVM switch and the computer is connected properly. Tighten any loose connections. • Try swapping your keyboard with a different one. • Try connecting the computer to a different port.
TROUBLESHOOTING • Deactivate power-management schemes on the PC that you are experiencing problems with. • Try swapping the mouse with a different one. The mouse is not detected at boot up. • Check the cables and make sure that they are inserted properly. The computer boots up fine, but the mouse does not work. • Make sure it is plugged in properly. • Make sure the mouse works when directly plugged into the computer. Rebooting may be necessary when trying this. • Try a different mouse.
TROUBLESHOOTING • You can reset the mouse and resume proper mouse movement simply by unplugging the mouse from the front of the SOHO Series KVM Switch for about 2–3 seconds, and then plugging it in again. GENERAL My computer does not boot when connected to the SOHO Series KVM Switch and works fine when I connect the keyboard, video, and mouse directly to it. • Make sure that the keyboard and mouse cables are connected tightly between the KVM switch and the computer.
TROUBLESHOOTING USB – (F1DS102T, F1DS104T) only I am connecting my computer to the USB SOHO Series KVM Switch via USB and my keyboard and mouse do not work. • Prior to connecting the USB SOHO Series KVM Switch, make sure that the HID USB driver is installed on each computer. (To install the HID USB driver, connect a USB mouse and USB keyboard to the computer. Windows should automatically install the drivers.) Some of the keys on my keyboard are not functioning properly when I use a Mac.
WARRANTY, TDD, CE STATEMENT FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Components, of 501 West Walnut Street, Compton CA 90220, declare under our sole responsibility that the product: F1DS102T, F1DS104T F1DS102P, F1DS104P to which this declaration relates: Complies with Part 15 of the FCC Rules.
belkin.com Belkin Components 501 West Walnut Street Compton • CA • 90220 • USA Tel: 310.898.1100 Fax: 310.898.1111 Belkin Components, Ltd. Unit 13 • Gatelodge Close • Round Spinney Northampton • Northants • NN3 8RX • United Kingdom Tel: +44 (0) 1604678300 Fax: +44 (0) 1604678330 Belkin Components B.V. Belkin Components B.V. Starparc Building • Boeing Avenue 333 1119 PH Schiphol-Rijk • The Netherlands Tel. +31 (0) 20 654 7300 Fax. +31 (0) 20 654 7349 Belkin Components, Ltd.
