N Wireless Modem Router User Manual PM01527ea F5D8636-4 English Français Deutsch Nederl ands Español Italiano
Table of Contents Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1 Introduction ���������������������������������������������������������������������������������������� 1 6 Using the Web-Based Advanced User Interface . . . . . . . . . . . . 38 Advantages of a Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Placement of your N Wireless Modem Router . . . . . . . . . . . . . . . . . . . 3 Changing LAN Settings .
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Thank you for purchasing the Belkin N Wireless Modem Router (the Router). Following are two short sections—the first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance. Please be sure to read through this User Manual completely, and pay special attention to the section entitled “Placement of your N Wireless Modem Router” on page 3.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Revolutionary N Wireless Technology with MIMO (N MIMO) Think of conventional radio transmission as a two-lane highway. The speed limit governs the maximum allowable flow of traffic through that lane. Compared with conventional radios, one-dimensional smart antenna systems help move traffic through that lane faster and more reliably—analogous to a four-lane road on which traffic consistently moves at a rate closer to the speed limit.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Placement of your N Wireless Modem Router Important Factors for Placement and Setup Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases.
Introduction Table of Contents sections 1 2 3 4 If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone: • Unplug and remove the battery from any cordless phone that operates on the 2.4GHz band (check manufacturer’s information). If this fixes the problem, your phone may be interfering. • If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless network.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 5. Secure Connections, VPNs, and AOL Secure connections can be interrupted by a computer’s power management setting, which causes it to “go to sleep.” The simplest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website. Secure connections typically require a user name and password, and are used where security is important.
Product Overview Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Product Features SPI Firewall In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin N Wireless Modem Router an ideal solution for your home or small office network.
Product Overview Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Built-In Dynamic Host Configuration Protocol (DHCP) MAC Address Filtering Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network. The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup.
Knowing your Modem Router Table of Contents sections 1 2 3 4 Package Contents • Belkin N Wireless Modem Router • Quick Installation Guide • Belkin Setup Assistant Software CD • RJ11 Telephone Cord • RJ45 Ethernet Networking Cable • ADSL (Asymmetric Digital Subscriber Line) Micro filter* • Power Supply • User Manual in CD • Network Status Display Guide • Security Guide *ADSL Micro filter varies by country.
Knowing your Modem Router Table of Contents sections 1 2 3 4 System Requirements • An active ADSL service with a telephone wall jack for connecting the Router • At least one computer with an installed network interface adapter • TCP/IP networking protocol installed on each computer • No other DHCP server on your local network assigning IP addresses to computers and devices • Internet browser A computer running Windows 2000, XP, or Vista; or Mac OS X v10.4 and v10.
Knowing your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1. Security The Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The Network Status Display is easily visible on the FRONT of the Router to provide you with information about network activity and status. See the Network Status Display Guide for more detailed information.
Knowing your Modem Router Table of Contents sections 1 4. Router/Power Status 2 3 4 When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. During this time, the “router” icon blinks. When the Router has completely booted up, the “router” icon becomes a solid light, indicating the Router is ready for use.
Knowing your Modem Router sections Table of Contents 8. Connection to ADSL 1 2 3 4 – Gray 6 7 8 9 10 10. Reset Button This port is for connection to your ADSL. Connect your ADSL to this port. An RJ11 telephone cord is provided in the package. 9. Connections to Wired Computers 5 The “Reset” button is used in rare cases when the Router may function improperly. Resetting the Router will restore the Router’s normal operation while maintaining the programmed settings.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Verify the contents of your box. You should have the following: Setup Assistant • Belkin N Wireless Modem Router • RJ11 Telephone Cord • RJ45 Ethernet Networking Cable • Power Supply • Belkin Setup Assistant Software CD Belkin has provided our Setup Assistant software to make installing your Router a simple and easy task. You can use it to get your Router up and running in minutes.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 1: Hardware Connections 1 3 2 5 4 1.1 Brand-New Setup Note: Some ADSL connections require a micro filter. Your ADSL provider can tell you if you need one. Belkin includes a micro filter in regions known to use them. You may or may not have received one in your box. Follow these steps if you are not replacing an existing modem.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1 3 1 ADSL 2 LAN 5 4 1.2 Replacing an Existing Modem or Modem Router Follow these steps if you currently have a modem or a modem router that you will be replacing with your new Router. 3. Locate the cable that connects your old modem to the ADSL wall jack. Unplug it from your old modem and then connect it to the gray port labeled “ADSL line” on the back of your Router.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 Step 2: Set Up the Router – Run the Setup Assistant Software 6 7 8 9 10 Select Country 1. Shut down any programs that are running on your computer at this time. Select your country from the drop-down box. Click “Begin” to continue. Turn off any firewall or Internet-connection-sharing software on your computer. 2. Insert the CD into your computer.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Confirmation Screen Progress Screen Verify that you have completed all QIG steps by checking the box to the right of the arrow. Click “Next” to continue. Setup Assistant will show you a progress screen each time a step in the setup has been completed.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 2.1 Checking Settings 2.2 Verifying Hardware Connections The Setup Assistant will now examine your computer’s network settings and gather information needed to complete the Router’s connection to the Internet. The Setup Assistant will now verify your hardware connection.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 2.3 Naming your Wireless Network 2.4 Requesting Internet Account Info (if needed) The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID). This is the name of your wireless network to which your computers or devices with wireless network adapters will connect. You can either use the default or change it to something unique. Write down this name for future reference.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 2.5 Configuring the Router If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below. Click “Next” to continue. The Setup Assistant will now configure your Router by sending data to the Router and restarting it. Wait for the on-screen instructions. Note: Do not disconnect any cable or power off the Router while the Router is rebooting.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 2.6 Checking Internet Connection Congratulations We are almost done. The Setup Assistant will now check your connection to the Internet. You have finished installing your new Belkin Router. You will see the Congratulations screen when your Router can connect to the Internet. You can begin surfing by opening your browser and going to any website.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Troubleshooting If the Setup Assistant is not able to connect to the Internet, you will see the following screen. Follow the on-screen instructions to go through the troubleshooting steps. 2.7 Optional: Assistance Connecting Other Computers This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 3: Set Up Wireless Security – Run the Security Assistant Software Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working. You can now surf the Internet. Click “Next” to return to the main menu.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Progress Screen 3.1 Picking the Security Type The Security Assistant will show you a progress screen each time a step has been completed. Select the security type for your wireless network and click “Next” to continue.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 3.2 Creating a Network Key 3.3 Transferring the Key Enter a network key (PSK) for your wireless network and click “Next” to continue. After setting up your wireless security, you will have to transfer the network key to each of your wireless computers. Click on “Transfer Key” if you have a USB flash drive. Follow the on-screen instructions, or click on “Print” to print the information.
Connecting and Configuring your Modem Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 3.4 Verifying the Connection Congratulations If all your wireless computers are able to connect to the Router, click “Next”. If you are having trouble, select “I had problem with at least one computer” and click “Next”. Then, follow on-screen instructions. Once you have verified that your wireless computers are properly connected, your wireless network is set up and secured.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 Step 1: Hardware Connections – Follow the Quick Installation Guide See the QIG or Step 1: Hardware Connections from the previous section. Step 2: Set your Computer’s Network Settings to Work with a DHCP Server See the section in this User Manual called “Manually Configuring Network Settings” for directions.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Logging into the Router Logging out of the Router You will see the Router’s home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Router’s settings, you have to log in. Clicking the “Login” button or clicking on any one of the links on the home page will take you to the login screen. The Router ships with no password entered.
Alternate Setup Method sections Table of Contents 1 2 3 4 5 6 7 8 9 10 Understanding the Web-Based Advanced User Interface The home page is the first page you will see when you access the Advanced User Interface (UI). The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1. Quick-Navigation Links 6. Connect/Disconnect Buttons You can go directly to any of the Router’s advanced UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find. Clicking on the purple header of each tab will show you a short description of the tab’s function.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 12. ADSL Info Connection Type Shows the ADSL status and transmission rates. From the “Connection Type” page, you can select one of these five connection types based on the instruction provided by your ISP: 13. Page Name The page you are on can be identified by this name. This User Manual will sometimes refer to pages by name. For instance “LAN > LAN Settings” refers to the “LAN Settings” page.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your ISP Connection Type to PPPoE or PPPoA PPPoE (Point-to-Point Protocol over Ethernet) is the standard method of connecting networked devices. It requires a user name and password to access the network of your ISP for connecting to the Internet. PPPoA (PPP over ATM) is similar to PPPoE, but is mostly implemented in the UK. Select PPPoE or PPPoA and click “Next”.
Alternate Setup Method Table of Contents sections 1 2 3 4 6. VPI/VCI – Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here. (Assigned by your ISP). 6 7 8 9 10 Setting your Connection Type to Dynamic/Fixed IP (1483 Bridged) This connection method bridges your network and ISP’s network together. The Router can obtain an IP address automatically from your ISP’s DHCP server or accept a fixed IP address assigned by your ISP. 7.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 For Dynamic IP connection: For Static IP connection: 1. IP assigned by ISP – Select “Yes” if your ISP instructed you to use Dynamic IP. 1. IP assigned by ISP – Select “No” if your ISP instructed you to use fixed IP. 2. VPI/VCI – Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here. These identifiers are assigned by your ISP. 2.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your ISP Connection Type to Static IP (IPoA) This connection type is also called “Classical IP over ATM” or “CLIP”, which your ISP provides a fixed IP for your Router to connect to the Internet. 1. WAN IP Address – Enter an IP address assigned by your ISP for the Router WAN interface. 2. Subnet Mask – Enter a subnet mask assigned by your ISP. 3. Use Static Default Gateway – Enter a default gateway IP address.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Connection Type to Modem Only (Disable Internet Sharing) In this mode, the Router simply acts as a bridge passing packets across the DSL port. It requires additional software to be installed on your computers in order to access the Internet. 1. Enable Bridge Service – Check this box to enable bridge service 2. VPI/VCI – Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameters here.
Alternate Setup Method Table of Contents sections 1 2 3 4 Setting Custom Domain Name Server (DNS) Settings 5 6 7 8 (1) A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locaters (URLs) like “ belkin.com” to IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 7 8 9 10 Viewing the LAN Settings Using your Internet browser, you can access the Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”) then press the “Enter” key. Clicking on the header of the LAN tab (1) will take you to the LAN tab’s header page. A quick description of the functions can be found here.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1. IP Address 4. IP Pool The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click “Apply Changes”. The IP address you choose should be a non-routable IP.
Using the Web-Based Advanced User Interface sections Table of Contents 1 2 3 4 5 6 7 8 9 10 Viewing the DHCP Client List Page Configuring the Wireless Network Settings You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computer’s network interface card (NIC).
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Changing the Wireless Network Name (SSID) 5 6 7 8 9 10 (1) To identify your wireless network, a name called the SSID is used. The SSID is your network name. The default network name of the Router is “Belkin_N_ADSL_” followed by six digits that are unique to your Router. Your network name will look something like “Belkin_N_ADSL_123456”. You can change this to anything you choose, or you can leave it unchanged.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Channel 1) Off There are a number of operating channels from which you can choose— in the United Kingdom (and most of Europe), Australia, and most of Asia, there are 13. In other countries, there are other channel requirements. Your Router is configured to operate on the proper channels for the country in which you reside. The channel can be changed if needed.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using the Bandwidth Switch Protected Mode Switch This switch allows you to set the Router’s wireless bandwidth modes. There are several modes available: Setting the Router to this mode allows it to switch automatically between 20MHz and 40MHz operation. This mode enables 40MHz operation, to maximize speed for N draft 802.11n-compliant devices when conditions permit. When a legacy 802.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Security Settings Your Router is equipped with the latest security standard called Wi-Fi Protected Access™ 2 (WPA2™) and the legacy security standard called Wired Equivalent Privacy (WEP). Your Router also supports the Wi-Fi Protected Setup (WPS) specification, which simplifies the setup of a wireless network.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Using Wi-Fi Protected Setup WPS uses WPA2 (described below) for encryption. It does not provide additional security, but rather, standardizes the method for securing your wireless network. You may use either the Push Button Configuration (PBC) method or PIN method to allow a device access to your wireless network.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 1. Wi-Fi Protected Setup (WPS): Enabled or Disabled. 6 7 8 9 10 IMPORTANT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2. At the time of this User Manual’s publication, a couple security patches are available, for free download, from Microsoft®.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WPA/WPA2-Personal (PSK) Like WPA security, WPA2 is available in WPA2-Personal (PSK) mode. Typically, WPA2-Personal (PSK) is the mode that will be used in a home environment. Please refer to the User Manual for more information about wireless security and different types of wireless security. 1.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WPA Security Note: To use WPA security, your wireless network cards must be equipped with software that supports WPA. At the time this User Manual was published, a security patch from Microsoft is available for free download. This patch works only with Windows XP. Your Router supports WPA-PSK. WPA-PSK uses what is known as a pre-shared key as the security key.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WEP Encryption Note to Mac users: The “Passphrase” option will not operate with Apple® AirPort®. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section. 1. Select “128-bit WEP” or “64-bit WEP” from the drop-down menu. 2.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from A–F and 0–9. 64-bit keys are 10 digits long and can be divided into five two-digit numbers. 128-bit keys are 26 digits long and can be divided into 13 two-digit numbers.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting MAC Address Control The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network. Note: This list applies only to wireless computers. This list can be configured so any computer attempting to access the wireless network that is not specified in the filter list will be denied access.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting up a Deny Access List The “Deny Access” list lets you specify computers that you DO NOT want to access the network. Any computer in the list will not be allowed access to the wireless network. All others will. (1) 1. Select the “Deny” radio button (1) to begin setting up a list of computers to be denied access to the wireless network. 2.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring the Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including: • IP Spoofing • Land Attack Ping of Death (PoD) • Denial of Service (DoS) • IP with zero length • Smurf Attack • TCP Null Scan • SYN flood • UDP flooding • Tear Drop Attack • ICMP defect • RIP defect • Fragment flooding N Wireless Mod
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring Internal Forwarding Settings Choosing an Application The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting Client IP Filters To restrict Internet access to a single computer for example, enter the IP address of the computer you wish to restrict access to in the IP fields (1). Next, enter “80” in both the port fields (2). Select “Both” (3). Select “Block” (4). You can also select “Always” to block access all of the time.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting MAC Address Filtering The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client (computer) on your network to allow network access to each.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Enabling the Demilitarized Zone (DMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Using Dynamic DNS The Dynamic DNS service allows you to alias a dynamic IP address to a static host name in any of the many domains DynDNS.org offers, allowing your network computers to be more easily accessed from various locations on the Internet. DynDNS.org provides this service, for up to five host names, free to the Internet community.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Blocking an ICMP Ping Computer hackers use what is known as “pinging” to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens your Router’s security level.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Utilities Restarting the Router The “Utilities” screen lets you manage different parameters of the Router and perform certain administrative functions. Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Restarting the Router to Restore Normal Operation 4. A 60-second countdown will appear on the screen. When the countdown reaches zero, the Router will be restarted. The Router home page should appear automatically. If not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser. 1. Click the “Restart Router” button. 2. The following message will appear. Click “OK”.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Saving a Current Configuration You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. 2. A window will open that allows you to select the location where you want to save the configuration file.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Restoring a Previous Configuration This option will allow you to restore a previously saved configuration. 1. Click “Browse”. A window will open that allows you to select the location of the configuration file. All configuration files end with a “.conf”. Locate the configuration file you want to restore and doubleclick on it. 2. You will be asked if you want to continue. Click “OK”.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 3. A reminder window will appear. It will take up to 60 seconds for the configuration restoration to complete. Click “OK”. 4. A 60-second countdown will appear on the screen. When the countdown reaches zero, the Router’s configuration will be restored. The Router’s home page should appear automatically. If not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Updating the Firmware From time to time, Belkin may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Router’s firmware to the latest version.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 Downloading a New Version of Firmware If you click the “Check Firmware” button and a new version of firmware is available, you will see a screen similar to the one below: 1. To download the new version of firmware, click “Download”.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 2. When the save is complete, you will see the following window. Click “Close”. A window will open that allows you to select the location where you want to save the firmware file. Select a location. You can name the file anything you want, or use the default name. Be sure to locate the file in a place where you can locate it yourself later. When you have selected the location, click “Save”. 3.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Updating the Router’s Firmware 1. In the “Firmware Update” page, click “Browse”. A window will open that allows you to select the location of the firmware update file. The “Update Firmware” box will now display the location and name of the firmware file you just selected. Click “Update”. 2. Browse to the firmware file you downloaded. Select the file by double-clicking on the file name. 3.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 4. You will see one more message. This message tells you that the Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted. Click “OK”. 5 6 7 8 9 10 Changing System Settings The “System Settings” page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Router.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Login Time-Out Setting The login time-out option allows you to set the period of time that you can be logged into the Router’s advanced setup interface. The timer starts when there has been no activity. For example, imagine you have made some changes in the advanced setup interface, then left your computer alone without clicking “Logout”.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Enabling Remote Management Enabling/Disabling UPnP Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Router’s settings from anywhere on the Internet. There are two methods of remotely managing the Router.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Enabling/Disabling Auto Firmware Update This innovation provides the Router with the built-in capability to automatically check for a new version of firmware and alert you that the new firmware is available. When you log into the Router’s advanced interface, the Router will perform a check to see if new firmware is available. If so, you will be notified. You can choose to download the new version or ignore it.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet. Manually Configuring Network Settings in Mac OS up to 9.x 3. Next to “Configure” (2), if “Manually” is selected, your Router will need to be set up for a static IP connection type.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 4. If not already set, at “Configure:”, choose “Using DHCP Server”. This will tell the computer to obtain an IP address from the Router. 5 7 8 9 Manually Configuring Network Settings in Mac OS X 1. Click on the “System Preferences” icon. 5. Close the window. If you made any changes, the following window will appear. Click “Save”. Select “Network” (1) from the “System Preferences” menu. Restart the computer.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 3. Select “Built-in Ethernet” (2) next to “Show” in the Network menu. 5 6 7 8 9 10 5. If “Manually” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. (2) (3) (4) (5) 6. If not already selected, select “Using DHCP” next to “Configure” (4), then click “Apply Now”.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 Manually Configuring Network Settings in Windows 2000, NT, or XP 5 6 7 8 9 10 5. If “Use the following IP address” (2) is selected, your Router will need to be set up for a static IP connection type. Write the address information the table below. You will need to enter this information into the Router. 1. Click “Start”, “Settings”, then “Control Panel”. 2.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 Manually Configuring Network Settings in Windows 98 or Me 6 7 8 9 10 3. If “Specify and IP address” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu. 4.
Recommended Web Browser Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the WebBased Advanced User Interface, then change your browser’s settings to the recommended settings in this section. Microsoft® Internet Explorer 4.0 or Higher 2.
Recommended Web Browser Settings Table of Contents sections 1 2 3 4 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. N Wireless Modem Router 5 6 7 8 9 10 Netscape® Navigator ® 4.0 or Higher 1. Start Netscape. Click on “Edit” then “Preferences”. 2.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Installation CD does not automatically start. Solution: If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive. 3. The Setup Assistant should start within a few seconds. If, instead, a window appears showing the files on the CD, double-click on the icon labeled “SetupAssistant.exe”. 1.
Troubleshooting Table of Contents sections 1 2 3 4 4. If the Setup Assistant still does not start, reference the section titled “Manually Configuring Network Settings” (page 74 of this User Manual) for an alternate setup method. 6 7 8 9 10 2. Unplug power to the Router for 10 seconds, and then plug the power back into the Router. Ensure that the Router’s Power light is on; it should be solid green.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Problem: The Setup Assistant cannot connect my Router to the Internet. • The Setup Assistant completed installation, but my web browser doesn’t work. If the Setup Assistant is not able to connect the Router to the Internet, please check the following items: • I am unable to connect to the Internet. The Router’s “Internet” light is off and the “Modem” light is blinking. 1.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Problem: Problem: • The Setup Assistant completed installation, but my web browser doesn’t work. • The Setup Assistant completed, but my web browser doesn’t work. • I am unable to connect to the Internet. The Router’s “Modem” light is on and the “Internet” light is blinking. • I am unable to connect to the Internet. The “Modem” light on my Router is blinking and the “Internet” light is solid.
Troubleshooting Table of Contents sections 1 2 3 4 Problem: 5 6 7 8 9 10 I can’t connect to the Internet wirelessly. 3. The exact window that opens will vary depending on the model of wireless card you have; however, any of the utilities should have a list of “Available Networks”—those wireless networks it can connect to.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 Problem: Problem: I can’t connect to the Internet wirelessly, and my network name is not listed. My wireless network performance is inconsistent. 10 Data transfer is sometimes slow. Solution: Signal strength is poor.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Channel Depending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability. The default channel the Router is shipped with is channel 11. You may choose from several other channels depending on your region (see the section titled “Changing the Wireless Channel” on page 43 for instructions on how to choose other channels).
Troubleshooting Table of Contents sections 1 2 3 4 Problem: 6 7 8 9 10 4. Click “Apply Changes” to finish. Encryption in the Wireless Router is now set. Each of your computers on your wireless network will now need to be configured with the same security settings. I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin Wireless Router or Belkin Access Point.
Troubleshooting Table of Contents sections 1 2 3 4 Problem: 5 6 7 8 9 10 IMPORTANT: A WEP key is a combination of numbers and letters from A–F and 0–7. For 128-bit WEP, you need to enter 26 keys. This network key needs to match the key you assign to your G Wireless Router or access point. I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card (Wireless Network Card or Adapter).
Troubleshooting Table of Contents sections 1 2 3 4 Problem: 5 6 7 8 9 10 1. Double-click the “Signal Indicator” icon to bring up the “Wireless Network Utility” screen. The “Advanced” button will allow you to view and configure more options of your client card. I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a Belkin Wireless Router or Belkin Access Point for a home network. 1. From the “Security Mode” drop-down menu, select “WPA-PSK”. 2.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 8 9 10 2. Once the “Advanced” button is clicked, the Belkin Wireless LAN Utility will appear. This Utility will allow you to manage all the advanced features of the Belkin client card. Supported Operating Systems: 3. Under the “Wireless Network Properties” tab, select a network name from the “Available Networks” list and click the “Properties” button. • Windows XP Home Edition 4. Under “Network Authentication”, select “WPA”. 1.
Troubleshooting Table of Contents sections 1 2 3 4 What’s the difference between 802.11b, 802.11g, 802.11a, and draft 802.11n? Currently there are four levels of wireless networking standards, which transmit data at very different maximum speeds. Each is based on the designation for certifying network standards. The most common wireless networking standard, 802.11b, transmits information at 11Mbps; 802.11a and 802.11g work at 54Mbps; and draft 802.11n works at 300Mbps.
Troubleshooting Table of Contents sections 1 2 3 4 5 6 7 Technical Support You can find technical-support information on our website, www.belkin.com, by navigating to the tech-support section. If you want to contact technical support by phone, please call the number you need from the list below*: *Local rates apply. N Wireless Modem Router Country Number Internet Address Austria 0820 200766 http://www.belkin.com/uk/networking/ Belgium 07 07 00 073 http://www.belkin.
Information Table of Contents sections 1 2 3 4 Europe-European Union Notice 5 6 7 8 9 10 Products with the CE marking comply with the EMC Directive (89/336/ EEC) and the Low Voltage Directive (72/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards).
Information Table of Contents sections 1 2 3 4 EU DECLARATION OF CONFORMITY ýesky [Czech] [Belkin Ltd] tímto prohlašuje, že tento [F5D8636-4] je ve shodČ se základními požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES. Dansk [Danish] Undertegnede [Belkin Ltd] erklærer herved, at følgende udstyr [F5D8636-4] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Belkin International, Inc., Limited Lifetime Product Warranty What this warranty covers. has been improperly installed, altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God such as flood, earthquake, lightning, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 How state law relates to the warranty. Belkin reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser.
Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, United Kingdom Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, France Belkin GmbH Hanebergstrasse 2 80637 Munich Germany Belkin Iberia C/ Anabel Segura, 10 planta baja, Of. 2 28108, Alcobendas, Madrid Spain Belkin Italy & Greece Via Carducci, 7 Milano 20123 Italy Belkin B.V. Boeing Avenue 333 1119 PH Schiphol-Rijk, Netherlands © 2008 Belkin International, Inc. All rights reserved.
