FireWire PCI Card Add 3 FireWire® ports directly to your computer EN FR DE NL ES IT User Manual F5U502/F5U503
FireWire PCI Card Add 3 FireWire® ports directly to your computer User Manual EN F5U502/F5U503
Table of Contents Introduction ............................................................................................... 1 Overview ..................................................................................................... 2 Features ............................................................................................... 2 Specifications ...................................................................................... 2 Package Contents ..........................................
Introduction Thank you for purchasing the Belkin IEEE-1394 PCI upgrade card. Now you can add three 400 Mbps FireWire ports to your Windows® 98 SE, Windows® 2000, or Windows® Me computer system and enjoy the blazing speed and Plug-and-Play ease of next-generation FireWire devices.
Overview Features • Three external 400 Mb/ps IEEE 1394 ports • IEEE 1394a Rev 5 compliant • Internal auxiliary power connector • IT/AT FIFO Buffers – 4k/2k • IR/AR FIFO Buffers – 4k/2k EN Specifications • OHCI 1.0 Compliant • PCI 2.1 and 2.2 compliant Package Contents • Belkin IEEE 1394 PCI card • Installation CD • User’s Manual Minimum Recommended System Requirements: • 266 Mhz Pentium II • 32 Megabytes RAM • One Free PCI 2.
Hardware Installation 1. Power off your computer and disconnect all connected devices and peripherals. EN 2. Open the case of your computer. Refer to your computer user manual for details regarding how to do this. Be sure to touch any bare metal portion of your computer case to discharge yourself of any static electricity, which can damage your computer, or the FireWire card.
Hardware Installation 3. Locate the PCI slots on your computer’s main circuit board. Locate a free PCI slot. Remove the metal plate that covers the rear slot corresponding to the PCI slot you had selected. You may need a cross-head/Phillips screwdriver to remove any screws. See the image below for your reference.
Hardware Installation 4. Remove the FireWire card from its protective static bag. Handle it by the metal bracket only, and do not touch the gold edge connectors. Insert the card into the PCI slot, carefully aligning the rear bracket to the computer case. Make sure that the gold fingers are fully inserted into the slot.
Hardware Installation 5. Fasten the card securely using the screw that was used to hold the rear bracket. EN 6. (Optional) If you are planning to connect multiple bus powered FireWire devices to the Belkin IEEE 1394 PCI card, it may be necessary to draw auxiliary power from your computers power supply. This is accomplished by connecting a spare disk drive power cable to the power connector on the PCI card.
Hardware Installation 7. Close the computer case. EN 8.
Software Installation Windows 98 SE Driver Installation 1. As Windows 98 SE starts the “New Hardware Wizard” will launch and recognize the IEEE 1394 PCI card as a “PCI OHCI compliant IEEE 1394 Host Controller”. Click “Next”. EN 2. Select “Search for the best driver for your device (Recommended)”. Click “Next”.
Software Installation 3. Uncheck all boxes. Click “Next”. EN 4. Windows will now search its driver database for the correct driver. Click “Next.
Software Installation 5. You may now be prompted to insert your Windows 98 SE installation disk. If so, insert the CD into your CD-ROM drive, and click “OK”. EN 6. Driver Installation is now complete. Click “Finish”.
Software Installation Windows 2000 Driver Installation 1. As Windows 2000 starts the “New Hardware Wizard” will launch, and recognize the IEEE 1394 PCI card as a “OHCI Compliant IEEE 1394 Host Controller”. EN 2. Windows will automatically install the correct driver and prompt you to restart your computer. Click “Yes”. Installation is now complete and the IEEE 1394 PCI card will be ready to use after Windows restarts.
Software Installation Windows Me Driver Installation 1. As Windows Me starts the “New Hardware Wizard” will launch, and recognize the IEEE 1394 PCI card as a “PCI OHCI Compliant IEEE 1394 Host Controller”. Choose “Automatic search for a better driver (Recommended)”. Click “Next”. EN 2. Windows will now locate and install the correct driver. Click “Finish”.
Software Installation 3. Windows will automatically install the correct driver and prompt you to restart your computer. Click “Yes”. Installation is now complete and the IEEE 1394 PCI card will be ready to use after Windows restarts.
EN 14
Information FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product: F5U502/F5U503 to which this declaration relates: Complies with Part 15 of the FCC Rules.
Belkin Corporation 501 West Walnut Street Compton, CA, 90220-5221, USA +1 310 898 1100 +1 310 898 1111 fax Belkin GmbH Hanebergstrasse 2 80637 Munich, Germany +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, France +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax Belkin B.V.
Carte PCI Firewire Ajoutez 3 ports FireWire® à votre ordinateur FR Manuel de l’utilisateur F5U502/F5U503
Table des matières Introduction ............................................................................................... 1 Présentation ............................................................................................... 2 Caractéristiques ................................................................................... 2 Spécifications ...................................................................................... 2 Contenu de l’emballage .........................................
Introduction Merci d’avoir fait l’achat de la carte de mise à niveau PCI IEEE-1394 Belkin. Vous pouvez désormais ajouter trois ports FireWire 400 Mbps à votre ordinateur sous Windows® 98 SE, Me ou 2000 et profiter de la rapidité et de la convivialité Plug-and-Play des périphériques FireWire.
Présentation Caractéristiques • Trois ports externes IEEE 1394 à 400 Mbps • Compatible IEEE 1394a rév. 5 • Connecteur interne d’alimentation auxiliaire • Tampons FIFO IT/AT 4 k/2 k • Tampons FIFO IR/AR 4 k/2 k Spécifications • Compatible OHCI 1.0 • Compatible avec les spécifications PCI 2.1 et 2.2 FR Contenu de l’emballage • Carte PCI IEEE 1394 Belkin • CD d’installation • Manuel d’utilisation Configuration minimale requise : • Pentium II 266 MHz • 32 Mo RAM • Un emplacement compatible PCI 2.
Installation du matériel 1. Éteignez votre ordinateur et débranchez tous les périphériques connectés. FR 2. Ouvrez le capot de votre ordinateur. Reportez-vous au manuel de l’utilisateur de votre ordinateur pour savoir comment faire. Veillez à toucher une partie métallique de votre ordinateur afin de décharger toute électricité statique qui risquerait d’endommager votre ordinateur ou la carte FireWire.
Installation du matériel 3. Recherchez les emplacements PCI sur la carte mère de votre ordinateur. Recherchez un emplacement PCI libre. Retirez l’obturateur métallique qui recouvre l’ouverture arrière correspondant à l’emplacement PCI sélectionné. Vous aurez besoin d’un tournevis cruciforme/Phillips pour retirer les vis. Reportez-vous à l’image ci-dessous pour vous aider.
Installation du matériel 4. Retirez la carte FireWire de son emballage anti-statique protecteur. Manipulez-la uniquement par les fixations métallique. Ne touchez pas les connecteurs dorés. Insérez la carte dans l’emplacement PCI en alignant correctement la fixation arrière sur le boîtier de l’ordinateur. Assurez-vous que les ergots dorés sont entièrement insérés dans l’emplacement.
Installation du matériel 5. Fixez la carte à l’aide de la vis qui permettait de maintenir la fixation arrière. FR 6 6. (Facultatif) Si vous planifiez de brancher plusieurs périphériques FireWire avec alimentation par le bus à la carte PCI IEEE 1394 Belkin, il se peut que vous deviez tirer de l’alimentation supplémentaire de la source d’alimentation de votre ordinateur. Pour ce faire, brancher un câble d’alimentation pour lecteur auxiliaire au connecteur d’alimentation de la carte PCI.
Installation du matériel 7. Refermez le capot de l’ordinateur. FR 8. Rebranchez tous les périphériques à votre ordinateur et allumez ce dernier.
Installation du logiciel Installation du pilote pour Windows 98 SE 1. Au démarrage de Windows 98 SE, l’assistant d’ajout de nouveau matériel est lancé et reconnaît la carte PCI IEEE 1394 en tant que « PCI OHCI compliant IEEE 1394 Host Controller ». Cliquez sur « Next [Suivant] ». FR 2. Choisissez l’option « Search for the best driver for your device [Rechercher le meilleur pilote pour votre périphérique] » (recommandé). Cliquez sur « Next [Suivant] ».
Installation du logiciel 3. Retirez toutes les marques des cases à cocher. Cliquez sur « Next [Suivant] ». FR 4. Windows recherche maintenant le pilote requis dans sa base de données. Cliquez sur « Next [Suivant] ».
Software Installation 5. Il se peut qu’un message vous demande d’insérer le disque d’installation de Windows 98 SE. Si tel est le cas, placez le CD dans le lecteur de CDROM, puis cliquez sur « OK ». FR 10 6. L’installation est terminée. Cliquez sur « Finish [Terminer] ».
Software Installation Installation du pilote pour Windows 2000 1. Au démarrage de Windows 2000, l’assistant d’ajout de nouveau matériel est lancé et reconnaît la carte PCI IEEE 1394 en tant que « OHCI compliant IEEE 1394 Host Controller ». FR 2. Windows installe automatiquement le pilote approprié. Un message vous demande de redémarrer votre ordinateur. Cliquez sur « Yes [Oui] ». L’installation est terminée. Vous pourrez utiliser la carte PCI IEEE 1394 après le redémarrage de Windows.
Software Installation Installation du pilote pour Windows Me 1. Au démarrage de Windows Me, l’assistant d’ajout de nouveau matériel est lancé et reconnaît la carte PCI IEEE 1394 en tant que « PCI OHCI compliant IEEE 1394 Host Controller ». Sélectionnez “« Automatic search for a better driver [Recherche automatique d’un meilleur pilote] » (recommandé). Cliquez sur « Next [Suivant] ». FR 2. Windows recherche le pilote approprié et l’installe. Cliquez sur « Finish [Terminer] ».
Software Installation 3. Windows installe automatiquement le pilote approprié. Un message vous demande de redémarrer votre ordinateur. Cliquez sur « Yes [Oui] ». L’installation est terminée. Vous pourrez utiliser la carte PCI IEEE 1394 après le redémarrage de Windows.
FR 14
Information Déclaration FCC DÉCLARATION DE CONFORMITÉ À LA RÉGLEMENTATION FCC EN MATIÈRE DE COMPATIBILITÉ ÉLECTROMAGNÉTIQUE Nous, Belkin Corporation, sis au 501 West Walnut Street , Compton CA, 90220, États-Unis, déclarons sous notre seule responsabilité que le produit : F5U502/F5U503 auquel se réfère la présente déclaration : est conforme aux normes énoncées à l’alinéa 15 de la réglementation FCC.
Belkin Corporation 501 West Walnut Street Compton, CA 90220-5221, États-Unis +1 310 898 1100 +1 310 898 1111 Fax Belkin GmbH Hanebergstrasse 2 80637 Munich, Allemagne +49 (0) 89 143405 0 +49 (0) 89 143405 100 Fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, Royaume-Uni +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 Fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, France +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 Fax Belkin B.V.
FireWire PCI-Karte Drei zusätzliche FireWire®Anschlüsse für Ihren Computer DE Benutzerhandbuch F5U502/F5U503
Inhaltsverzeichnis Einleitung ................................................................................................... 1 Übersicht .................................................................................................... 2 Merkmale ............................................................................................. 2 Technische Daten................................................................................. 2 Verpackungsinhalt.............................................
Einleitung Herzlichen Glückwunsch zum Kauf der Belkin IEEE-1394 PCI-Karte.
Übersicht Merkmale • Drei externe IEEE 1394-Anschlüsse mit 400 Mbit/s • Entspricht dem Standard IEEE 1394a 5 Rev5 • Zusätzlicher interner Stromanschluss • IT/AT FIFO-Puffer – 4k/2k • IR/AR FIFO Puffer – 4k/2k Technische Daten • Entspricht dem Standard OHCI 1.0 • Entspricht den Standards PCI 2.1 und 2.
Hardware-Installation 1. Schalten Sie den Computer aus, und stecken Sie alle angeschlossenen Geräte ab. DE 2. Öffnen Sie das Computergehäuse. Genaue Anweisungen hierzu finden Sie in Ihrem Computerhandbuch. Berühren Sie ein beliebiges Stück blankes Metall am Computergehäuse, um etwaige statische Ladung von sich abzuleiten, die den Computer oder die FireWire-Karte beschädigen könnte.
Hardware-Installation 3. Suchen Sie die PCI-Steckplätze auf der Hauptplatine Ihres Computers. Sie können einen beliebigen freien PCI-Steckplatz verwenden. Entfernen Sie die Metallschiene, die die Rückwandöffnung für den ausgewählten PCI-Steckplatz abdeckt. Möglicherweise benötigen Sie einen Kreuzschlitz schraubendreher, um Schrauben zu entfernen. Siehe hierzu die Abbildung unten.
Hardware-Installation 4. Nehmen Sie die FireWire-Karte aus dem Antistatik-Beutel. Berühren Sie die Karte nur an der Metalleinbauschiene, nicht an den vergoldeten Kartenrand-Steckverbindern! Stecken Sie die Karte in den PCISteckplatz ein, und richten Sie die Rückwand-Einbauschiene sorgfältig am Computergehäuse aus. Achten Sie darauf, dass die Goldkontakte vollständig in den Steckplatz eingesteckt sind.
Hardware-Installation 5. Sichern Sie die Karte mit der Schraube, mit der die RückwandAbdeckung befestigt war. DE 6 6. (Optional) Wenn Sie mehrere busgepeiste FireWire-Geräte an die Belkin IEEE 1394 PCI-Karte anschließen möchten, müssen Sie eventuell eine zusätzliche Stromversorgung installieren, die über den Rechner gespeist wird. Hierzu schließen Sie einen freien Festplatten-Stromstecker an die entsprechende Buchse auf der PCI-Karte an.
Hardware-Installation 7. Schließen Sie das Computergehäuse. DE 8.
Software-Installation Treiberinstallation unter Windows 98 SE 1. Windows 98SE startet den Hardware-Assistenten und erkennt die IEEE 1394 PCI-Karte als „PCI OHCI compliant IEEE 1394 Host Controller”. Klicken Sie auf „Next” (Weiter). DE 2. Wählen Sie „Search for the Best Driver for your device (Recommended)” (Nach dem besten Treiber für das Gerät suchen [empfohlen]). Klicken Sie auf „Next” (Weiter).
Software-Installation 3. Heben Sie die Markierung aller Kontrollkästchen auf. Klicken Sie auf „Next” (Weiter). DE 4. Windows sucht jetzt in der Treiberdatenbank nach dem richtigen Treiber. Klicken Sie auf „Next” (Weiter).
Software-Installation 5. Möglicherweise werden Sie jetzt dazu aufgefordert, die Windows 98 SE Installations-CD einzulegen. Ist dies der Fall, legen Sie die CD-ROM ein, und klicken Sie auf „OK”. 6. Die Treiberinstallation ist damit abgeschlossen. Klicken Sie auf „Finish” (Fertig stellen).
Software-Installation Treiberinstallation unter Windows 2000 1. Windows 2000 startet den Hardware-Assistenten und erkennt die IEEE 1394 PCI-Karte als „PCI OHCI compliant IEEE 1394 Host Controller”. DE 2. Windows installiert den richtigen Treiber automatisch und fordert Sie auf, das System neu zu starten. Klicken Sie auf „Yes” (Ja). Die Installation ist damit abgeschlossen. Die IEEE 1394 PCI-Karte steht nach dem Neustart von Windows zur Verfügung.
Software-Installation Treiberinstallation unter Windows ME 1. Windows ME startet den Hardware-Assistenten und erkennt die IEEE 1394 PCI-Karte als „PCI OHCI compliant IEEE 1394 Host Controller”. Wählen Sie die Option „Automatisch nach dem besten Treiber suchen (Empfohlen)”. Klicken Sie auf „Next” (Weiter). DE 2. Windows sucht jetzt nach dem richtigen Treiber und installiert ihn. Klicken Sie auf „Finish” (Fertig stellen).
Software-Installation 3. Windows installiert den richtigen Treiber automatisch und fordert Sie auf, das System neu zu starten. Klicken Sie auf „Yes” (Ja). Die Installation ist damit abgeschlossen. Die IEEE 1394 PCI-Karte steht nach dem Neustart von Windows zur Verfügung.
DE 14
Informationen FCC-Erklärung KONFORMITÄTSERKLÄRUNG ZUR EINHALTUNG DER FCC-BESTIMMUNGEN ÜBER ELEKTROMAGNETISCHE VERTRÄGLICHKEIT Wir, Belkin Corporation, eine Gesellschaft mit Sitz in 501 West Walnut Street, Compton, CA 90220, USA, erklären hiermit in alleiniger Verantwortung, dass dieses Produkt mit der Artikelnr. F5U502/F5U503, auf das sich diese Erklärung bezieht, in Einklang mit Teil 15 der FCC-Bestimmungen steht.
Belkin Corporation 501 West Walnut Street Compton, CA, 90220-5221, USA +1 310 898 1100 +1 310 898 1111 Fax Belkin GmbH Hanebergstraße 2 80637 München, Deutschland +49 (0) 89 143405 0 +49 (0) 89 143405 100 Fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, Großbritannien +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 Fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, Frankreich +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 Fax Belkin B.V.
FireWire PCI-kaart Breid uw computer uit met drie FireWire®-poorten NL Handleiding F5U502/F5U503
Inhoud Inleiding ...................................................................................................... 1 Overzicht .................................................................................................... 2 Productkenmerken ............................................................................... 2 Technische gegevens ........................................................................... 2 Inhoud van de verpakking .......................................................
Inleiding Belkin dankt u hartelijk voor het kopen van de IEEE-1394 PCI-upgradekaart. U kunt uw computersysteem dat draait onder Windows® 98 SE, Windows® 2000 of Windows® Me nu uitbreiden met drie FireWire-poorten van 400 Mbps en profiteren van de enorme snelheid en het Plug-and-Play-gemak van de jongste generatie FireWire-apparaten.
Overzicht Productkenmerken • Drie externe 400Mbps IEEE 1394-poorten • Voldoet aan IEEE 1394a rev. 5 • Interne hulpconnector voor voeding • IT/AT FIFO-buffers – 4k/2k • IR/AR FIFO-buffers – 4k/2k Technische gegevens • Voldoet aan OHCI 1.0 Voldoet aan PCI 2.1 en 2.2 Inhoud van de verpakking • IEEE 1394 PCI-kaart • Installatie-cd • Handleiding NL Aanbevolen minimale systeemvereisten: • 266Mhz Pentium II • 32 Mb RAM • Eén vrije PCI-sleuf conform PCI 2.
Hardware installeren 1. Schakel uw computer uit en ontkoppel alle aangesloten toestellen en randapparaten. NL 2. Verwijder de kap van uw computer. Raadpleeg de handleiding van uw computer voor meer informatie over hoe u dit moet doen. Zorg ervoor dat u een van de blanke metalen delen van uw computer aanraakt om uzelf te ontdoen van statische elektriciteit die uw computer of de FireWire-kaart kan beschadigen.
Hardware installeren 3. Zoek op het moederbord van uw computer de PCI-sleuven op. Zoek een vrije PCI-sleuf op. Verwijder aan de achterkant van uw computer het metalen afdekplaatje dat correspondeert met de PCI-sleuf die u hebt gekozen. Mogelijk hebt u een kruiskop/Phillips-schroevendraaier nodig om schroefjes los te draaien. Bekijk voor de duidelijkheid de onderstaande afbeelding.
Hardware installeren 4. Haal de FireWire-kaart uit de anti-statische verpakking. Pak de kaart uitsluitend bij de metalen beugel vast en raak de vergulde randconnectors niet aan. Bevestig de kaart in de PCI-sleuf en zorg ervoor dat de houder aan de achterkant evenwijdig loopt met de computerkast. Zorg ervoor dat de vergulde pennen volledig in de sleuf zijn gestoken.
Hardware installeren 5. Zet de kaart zorgvuldig vast met de schroef waarmee de beugel aan de achterzijde van de computer was vastgezet. NL 6 6. (Optioneel) Als u van plan bent meerdere FireWire-apparaten met busvoeding op de IEEE 1394 PCI-kaart van Belkin aan te sluiten, kan het nodig zijn extra voeding te onttrekken aan de hoofdvoeding van uw computer. Dit kunt u bereiken door op de voedingsingang van de PCIkaart een reserve-voedingskabel aan te sluiten.
Hardware installeren 7. Plaats de computerkap weer terug. 8. Sluit alle randapparaten weer op uw computer aan en zet de computer aan.
Software installeren Stuurprogramma’s installeren onder Windows 98 SE 1. Wanneer Windows 98 SE de wizard “New Hardware” (Nieuwe hardware) start, wordt de IEEE 1394 PCI-kaart herkend als“PCI OHCI compliant IEEE 1394 Host Controller”. Klik op “Next” (Volgende). NL 2. Selecteer “Search for the best driver for your device (Recommended)” (Zoek het beste stuurprogramma voor uw apparaat op (Aanbevolen)). Klik op “Next” (Volgende).
Software installeren 3. Verwijder alle vinkjes uit de selectievakjes. Klik op “Next” (Volgende). 4. Windows zoekt nu in zijn database met stuurprogramma’s naar het juiste stuurprogramma. Klik op “Next” (Volgende).
Software installeren 5. Mogelijkerwijs vraagt de computer om de installatie-cd van Windows 98 SE. In dat geval dient u de installatie-cd in uw cd-romstation te plaatsen en op “OK” te klikken. 6. De stuurprogramma-installatie is nu afgerond. Klik op “Finish” (Voltooien).
Software installeren Stuurprogramma’s installeren onder Windows 2000 1. Wanneer Windows 2000 de “New Hardware Wizard” (Nieuwe hardware wizard) start, wordt de IEEE 1394 PCI-kaart herkend als “OHCI Compliant IEEE 1394 Host Controller”. 2. Windows installeert automatisch het juiste stuurprogramma en vraagt u vervolgens uw computer opnieuw te starten. Klik op “Yes” (Ja). De installatie is nu voltooid en de IEEE 1394 PCI-kaart zal gebruiksklaar zijn zodra Windows opnieuw is gestart.
Software installeren Stuurprogramma’s installeren onder Windows Me 1. Wanneer Windows Me de “New Hardware Wizard” (Nieuwe hardware wizard) start, wordt de IEEE 1394 PCI-kaart herkend als “PCI OHCI Compliant IEEE 1394 Host Controller”. Kies “Automatic search for a better driver (Recommended)” (Automatisch naar een beter stuurprogramma zoeken (Aanbevolen)). Klik op “Next” (Volgende). NL 2. Windows vindt en installeert nu het juiste stuurprogramma. Klik op “Finish” (Voltooien).
Software installeren 3. Windows installeert automatisch het juiste stuurprogramma en vraagt u vervolgens uw computer opnieuw te starten. Klik op “Yes” (Ja). De installatie is nu voltooid en de IEEE 1394 PCI-kaart zal gebruiksklaar zijn zodra Windows opnieuw is gestart.
NL 14
Informatie FCC-verklaring VERKLARING VAN CONFORMITEIT MET DE FCC-VOORSCHRIFTEN VOOR ELEKTROMAGNETISCHE COMPATIBILITEIT Wij, Belkin Corporation, gevestigd 501 West Walnut Street, Compton, CA 90220, Verenigde Staten van Amerika, verklaren hierbij dat wij de volledige verantwoordelijkheid aanvaarden dat het product met het artikelnummer F5U502/F5U503 waarop deze verklaring betrekking heeft, voldoet aan deel 15 van de FCC-regelgeving.
Belkin Corporation 501 West Walnut Street Compton, CA, 90220-5221, USA +1 310 898 1100 +1 310 898 1111 fax Belkin GmbH Hanebergstraße 2 80637 München, Duitsland +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, Verenigd Koninkrijk +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, Frankrijk +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax Belkin B.V.
Tarjeta PCI FireWire Añada 3 puertos FireWire® directamente a su ordenador ES Manual del usuario F5U502/F5U503
Índice de contenidos Introducción ............................................................................................... 1 Generalidades ............................................................................................ 2 Características ..................................................................................... 2 Especificaciones .................................................................................. 2 Contenido del paquete ...........................................
Introducción Gracias por adquirir la Tarjeta de actualización PCI IEEE-1394 de Belkin. Ahora podrá añadir tres puertos FireWire de 400 Mbps a su sistema operativo Windows® 98 SE, Windows® 2000, o Windows® Me y disfrutar de la velocidad ultrarrápida y de la comodidad plug-and-play de de los dispositivos FireWire.
Generalidades Características • Tres puertos externos IEEE 1394 de 400 Mbps • Cumple con IEEE 1394a rev. 5 • Enchufe de corriente auxiliar interno • Búferes FIFO IT/AT – 4 k/2 k • Búferes FIFO IR/AR – 4 k/2 k Especificaciones • Cumple con OHCI 1.0 • Compatible con PCI 2.1 y 2.
Instalación del hardware 1. Apague su ordenador y desconecte todos los dispositivos y periféricos conectados. 2. Abra la carcasa de su ordenador. Consulte el manual de usuario de su ordenador para más información al respecto. Toque cualquier parte metálica de la carcasa de su ordenador para descargar la electricidad estática y evitar que su ordenador o la Tarjeta FireWire sufran daños.
Instalación del hardware 3. Localice las ranuras PCI en la placa base de circuitos de su ordenador. Localice una ranura libre PCI. Extraiga la placa de metal que cubre la ranura trasera que corresponde con la ranura PCI que ha seleccionado. Puede que necesite un destornillador de estrella/Phillips para retirar los tornillos. Consulte la ilustración siguiente como referencia.
Instalación del hardware 4. Extraiga la Tarjeta de su envoltorio protector antiestático. Sujétela sólo por el soporte de metal, y no toque los conectores con extremos dorados. Inserte la Tarjeta en la ranura PCI, alineando con cuidado el soporte trasero con la carcasa del ordenador. Asegúrese de que los conectores dorados están insertados completamente en la ranura.
Instalación del hardware 5. Fije la Tarjeta correctamente utilizando el tornillo que sujetaba el soporte trasero. 6. (Opcional) Si va a conectar varios dispositivos FireWire alimentados a través del bus a la Tarjeta PCI IEEE 1394 PCI de Belkin, puede que sea necesario extraer alimentación auxiliar de la fuente de alimentación de su ordenador. Esto puede realizarse conectando un cable adicional de alimentación de unidad de disco al conector de alimentación de la Tarjeta PCI.
Instalación del hardware 7. Cierre la carcasa del ordenador. 8.
Instalación del software Instalación del controlador en Windows 98 SE 1. Cuando Windows 98 SE se inicie, se abrirá el Asistente para nuevo hardware y reconocerá la Tarjeta PCI IEEE 1394 PCI como un “PCI OHCI compliant IEEE 1394 Host Controller” (Controlador de host IEEE 1394 válido para OHCI PCI) Haga clic en “Next” (Siguiente). ES 2. Seleccione “Search for the best driver for your device (Recommended)” (Buscar el mejor controlador para su dispositivo, recomendado). Haga clic en “Next” (Siguiente).
Instalación del software 3. Quite la selección de todos los recuadros. Haga clic en “Next” (Siguiente). 4. Windows buscará ahora el controlador correcto en su base de datos de controladores de software. Haga clic en “Next” (Siguiente).
Instalación del software 5. Es posible que ahora se le solicite la inserción de su disco de instalación de Windows 98 SE. En tal caso, inserte su CD en la unidad de CD-ROM y haga clic en “OK” (Aceptar). 6. Se ha completado la instalación del controlador. Haga clic en “Finish” (Finalizar).
Instalación del software Instalación del controlador en Windows 2000 1. Cuando Windows 2000 se inicie, se abrirá el Asistente para nuevo hardware y reconocerá la Tarjeta PCI IEEE 1394 PCI como un “OHCI compliant IEEE 1394 Host Controller” (Controlador de host IEEE 1394 válido para OHCI) 2. Windows instalará automáticamente el controlador apropiado y le solicitará que reinicie su ordenador. Haga clic en “Yes” (Sí).
Instalación del software Instalación del controlador en Windows Me 1. Cuando Windows Me se inicie, se abrirá el Asistente para nuevo hardware y reconocerá la Tarjeta PCI IEEE 1394 PCI como un “PCI OHCI compliant IEEE 1394 Host Controller” (Controlador de host IEEE 1394 válido para PCI OHCI) Seleccione “Automatic search for a better driver (recommended)” (Buscar automáticamente un controlador mejor, recomendado). Haga clic en “Next” (Siguiente). ES 2.
Instalación del software 3. Windows instalará automáticamente el controlador apropiado y le solicitará que reinicie su ordenador. Haga clic en “Yes” (Sí). La instalación se ha completado y la Tarjeta PCI IEEE 1394 estará lista para ser utilizada después de reiniciar Windows.
ES 14
Información Declaración de la FCC (Comisión de comunicaciones de EE.UU.) DECLARACIÓN DE CONFORMIDAD CON LAS NORMATIVAS DE LA FCC SOBRE COMPATIBILIDAD ELECTROMAGNÉTICA Nosotros, Belkin Corporation, con sede en 501 West Walnut Street, Compton, CA 90220 (EE.UU.), declaramos bajo nuestra sola responsabilidad que el producto: F5U502/F5U503 al que hace referencia la presente declaración: Cumple con la sección 15 de las normativas de la FCC.
Belkin Corporation 501 West Walnut Street Compton, CA, 90220-5221, EE.UU. +1 310 898 1100 +1 310 898 1111 fax Belkin GmbH Hanebergstrasse 2 80637 Múnich, Alemania +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, Reino Unido +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, Francia +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax Belkin B.V.
Scheda PCI FireWire Il modo più veloce per aggiungere 3 porte FireWire® al computer IT Manuale d’uso F5U502/F5U503
Indice Introduzione ............................................................................................... 1 Descrizione generale................................................................................. 2 Caratteristiche ..................................................................................... 2 Specifiche ............................................................................................ 2 Contenuto della confezione .....................................................
Introduzione Grazie per aver acquistato la scheda PCI IEEE-1394 Belkin. Ora è possibile aggiungere tre porte FireWire a 400 Mbps a computer con Windows ® 98 SE, Windows® 2000 o XP e usufruire di altissime velocità di trasferimento e della funzionalità Plug and Play dei dispositivi FireWire di prossima generazione.
Descrizione generale Caratteristiche • Tre porte esterne IEEE 1394 a 400 Mbps • Conforme alle specifiche IEEE 1394a 5 • Connettore per alimentazione ausiliaria interna • Buffer IT/AT FIFO – 4k/2k • Buffer IR/AR FIFO – 4k/2k Specifiche • Conformità alle specifiche OHCI 1.0 • Conformità allo standard PCI 2.1 e 2.
Installazione dell’hardware 1. Spegnere il computer e scollegare tutti i dispositivi e le periferiche. 2. Aprire il telaio del computer. Prima di eseguire questa operazione, consultare il manuale d’uso del computer. Toccare una parte metallica del telaio del computer per scaricare l’elettricità statica. Questo eviterà di danneggiare il computer e la scheda FireWire.
Installazione dell’hardware 3. Individuare gli slot PCI sul circuito stampato del computer. Individuare uno slot PCI libero. Rimuovere la lastra di metallo che ricopre lo slot sul retro corrispondente allo slot PCI Express selezionato. Utilizzare un cacciavite a croce per rimuovere le viti. Fare riferimento alle immagini sotto illustrate.
Installazione dell’hardware 4. Rimuovere la scheda FireWire dalla sua confezione antistatica. Mantenere la scheda dalla staffa metallica: non toccare i connettori con le terminazioni dorate. Inserire la scheda nello slot PCI allineando attentamente la staffa posteriore con il pannello del computer. Verificare che il bordo della scheda PCI sia completamente inserito nello slot.
Installazione dell’hardware 5. Fissare la scheda in modo sicuro utilizzando la vite utilizzata per la staffa posteriore. 6. (Opzionale) Se si desidera collegare a questa scheda diversi dispositivi FireWire alimentati via bus, occorre ricavare l’energia elettrica dall’alimentatore del computer. A tal fine, è necessario collegare un cavo di alimentazione per unità a disco al connettore sulla scheda PCI.
Installazione dell’hardware 7. Richiudere il telaio del computer. 8.
Software d’installazione Installazione del driver per Windows 98 SE 1. Windows 98 SE avvierà il programma di “Installazione guidata nuovo hardware” e rileverà la scheda PCI IEEE 1394 come “PCI OHCI compliant IEEE 1394 Host Controller”. Fare clic su “Next” (Avanti). IT 8 2. Selezionare “Search for the best driver for your device” (Cerca driver migliore). Fare clic su “Next” (Avanti).
Software d’installazione 3. Non selezionare alcuna casella. Fare clic su “Next” (Avanti). 4. Windows ricercherà ora il driver corretto nel proprio database. Fare clic su “Finish” (fine).
Software d’installazione 5. È possibile che il sistema richieda l’inserimento del CD di installazione di Windows 98 SE. In tal caso, inserire il CD di Windows 98 e fare clic su “OK”. 6. L’installazione è completata. Fare clic su “Finish” (Fine).
Software d’installazione Installazione del driver per Windows 2000 1. Windows 2000 SE avvierà il programma di “Installazione guidata nuovo hardware” e rileverà la scheda PCI IEEE 1394 come “OHCI Compliant IEEE 1394 Host Controller”. 2. Windows installerà automaticamente il driver corretto e vi richiederà di riavviare il computer. Fare clic su “Yes” (Sì). L’installazione è completata e la scheda PCI IEEE 1394 sarà pronta per l’uso dopo il riavvio di Windows.
Software d’installazione Installazione del driver per Windows ME 1. Windows 2000 SE avvierà il programma di “Installazione guidata nuovo hardware” e rileverà la scheda PCI IEEE 1394 come “PCI OHCI Compliant IEEE 1394 Host Controller”. Selezionare “Automatic search for a better driver (recommended)” (Cerca driver migliore). Fare clic su “Next” (Avanti). IT 12 2. Windows ora ricercherà e installerà il driver corretto. Fare clic su “Finish” (Fine).
Software d’installazione 3. Windows installerà automaticamente il driver corretto e vi richiederà di riavviare il computer. Fare clic su “Yes” (Sì). L’installazione è completata e la scheda PCI IEEE 1394 sarà pronta per l’uso dopo il riavvio di Windows.
IT 14
Informazioni Dichiarazione FCC DICHIARAZIONE DI CONFORMITÀ ALLE NORME FCC LA COMPATIBILITÀ ELETTROMAGNETICA Belkin Corporation, con sede al 501 West Walnut Street, Compton, CA 90220, dichiara sotto la propria piena responsabilità che il prodotto, F5U502/F5U503 cui questa dichiarazione fa riferimento: è conforme alla Parte 15 delle norme FCC.
Belkin Corporation 501 West Walnut Street Compton, CA, 90220-5221, USA +1 310 898 1100 +1 310 898 1111 fax Belkin GmbH Hanebergstrasse 2 80637 Monaco di Baviera, Germania +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, Regno Unito +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, Francia +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax Belkin B.V.
Belkin Corporation 501 West Walnut Street Compton, CA, 90220-5221, USA +1 310 898 1100 +1 310 898 1111 fax Belkin GmbH Hanebergstrasse 2 80637 Munich, Germany +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, France +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax Belkin B.V.