Line Interactive 600VA UPS Quick Install Guide F6U600au
Introduction Each year, several natural and man-made occurrences put the power supplied to your electronics in your home or office in jeopardy. At risk are your hardware, software, and data because of these power problems. This product is designed to provide clean power to all computer systems and peripherals with maximum protection. It integrates quality surge protection and battery backup capabilities to provide complete power protection for your computer, modem, hard drive, and other related equipment.
- Charging This unit is shipped from the factory with its internal battery fully charged, however some charge may be lost during shipping and the battery should be recharged prior to use. Plug the unit into an appropriate power outlet and allow the UPS to charge fully by leaving it plugged in for at least 6 hours with no load (no electrical devices such as computers, monitors, etc) connected.
5 - Peripheral Equipment Connection Plug your peripheral equipment (printer, scanner or speakers) into the full-time surge protection outlet. This receptacle does not provide any power during a power failure. Printer Note: DO NOT plug a laser printer, copier, space heater, vacuum or other large electrical device into the UPS. The power demands of these devices will overload and possibly damage the unit. 6 - Modem/Phone line Connection Plug incoming phone line into the "IN" socket on the front of the UPS.
7 - Turn On/Off Press power switch to turn on the UPS. Press power switch again to turn off the UPS. 8 - DC Start Function DC Start Function enables UPS to be started up when AC utility power is not available and battery is fully charged.
Installing Belkin Automatic Power Management Software Step 1: PC Installation Mac Installation - Insert CD - Insert CD - After a short moment - Open “Belkin APMS” CD icon the CD will automatically - Open Mac OSX folder run - Open Disk 1 folder - Open INSTDATA folder - Select setup icon Follow prompts until software is installed (Note: Mac users will be prompted to restart at the end of this process, do so) Upon completion you will now have an “agent’ icon in your syst
Installing Belkin Automatic Power Management Software Step 2: To launch the software, PC - double click agent icon in your system tray to start the monitor Mac - click the agent icon in your dock and select “Start Monitor” Step 3: Select System Menu then “Auto Search UPS”, the software should now detect your connected UPS.
Important Safety Instructions Caution Please read the following information carefully and save this manual for future reference. Disregard of these safety notes may endanger life or health, as well as the function of the equipment and the safety of your data. • Do not connect this product to another battery backup, power board, surge protector, extension cord or double adapter. • Risk of Electric Shock. Heatsinks are live. Disconnect unit before servicing. • Risk of Electric Shock.
Specification Model F6U600au Capacity VA/W 600VA/360W Voltage 220/230/240VAC Input Frequency 50/60Hz Output (inverter Mode) Transfer Time Battery Phase Single Voltage Range 220/230/240VAC+10% Frequency 50Hz or 60Hz+1Hz Waveform Modified Sinwave Typical 2-6ms Battery Type 12V7Ahx1 Backup Time at a PC load with monitor (Typical 100W) 16-18 Minutes Recharging Time 6 hours max (recharge up to 90% capacity) LED Power on, Backup, Fault Battery Mode Sounding every 10 seconds Low Bat
System Description Front 1 Power Switch 2 LCD indicators AC Mode: Green Lighting Battery Mode: Green Flashing Back 1 Battery Backup & Surge Outlets 2 Input & Fuse Inlet 3 Modem/Phone Line Surge Protection 4 USB Port 5 Surge Protection Outlet 10
Troubleshooting If the UPS failed to operate properly, please review the following points first. Symptom Possible Cause Remedy LED is flashing and audible alarm is heard intermittently. UPS is not connected properly to the mains. Connect the UPS according to the installation guide. UPS is functioning but audible alarm is heard continuously. Overload of the UPS. Verify that the load matches the UPS capacity stated in the specifications. Communication lost between UPS and computer.
