WATCH LIVE AND RECORDED TV ON YOUR MOBILE DEVICES—ANYWHERE. @TVplus User Manual G1V1000 • 8820-01176 Rev.
SETUP AND INSTALLATION 1. Getting @TV connected to your home network The @TV setup software for PC and Mac is the best way to configure @TV. Visit http://www.belkin.com/mytveverywhere to download the software. a. Wired i. Direct connection via an Ethernet cable will provide the best possible performance for your @TV product. Simply connect the cable to one of the open ports on your broadband-connected network router and then to the Ethernet port on your @TV. ii.
SETUP AND INSTALLATION c. Advanced network connections @TV will use UPnP to configure our network connection. In some cases you will need to use your router’s setup pages to change a few settings. i. Apple using 3G/4G 1. I n order to access @TV on a 3G or 4G network using an Apple product like an iPhone, you may need to modify your Port Forwarding settings.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX 2. Connecting to your cable or satellite set-top box disable analog outputs like the ones @TV uses whenever an HDMI enabled device (like an HDTV) is connected to them; this is because that particular cable or satellite box manufacturer has chosen to enable advanced content protection protocols that are triggered by your TV/STB combination.
INSTALLING AND SETTING UP THE ADAPTER d. Advanced settings tab i. Video 1. Input a. Component vs. Composite i. Allows you to select which input on your @TV you would like to use. We recommend using component as it provides the highest video quality. ii. I t is possible to attach two separate devices to @TV and toggle between these inputs in your App.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX b. Hue, saturation, brightness, contrast i. Various settings to help you optimize the look of your @TV’s video c. Default i. Automatically resets the picture optimization settings to their initial settings 2. Device/STB This section is used to manually configure your remote control settings so that your @TV can control your set-top box.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX 3. IR-Learning In this section you can help your @TV “learn” remote commands. This is particularly useful if you have a cable or satellite box not currently supported by @TV. The steps are as follows: a. S elect the appropriate device you are trying to control from the “Command Mapping” list. b. F rom the list below, select the command that you are trying to capture and then click “Learn.” c.
INSTALLING AND SETTING UP THE ADAPTER 4. IR-Channel Tuning a. C able and set-top boxes vary in what they require when you enter a channel. For instance, on some boxes going to channel 42 requires just that you enter 42 while on another you must enter 042 or 0042. This section allows you to manually configure your @TV so that it works well with your set-top box.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX 5. Wake-up a. Some boxes require a “wake-up” command; in this section you can automatically set that command when you start streaming from your set-top box to your @TV app. For most cable or satellite boxes, these commands are automatically configured when you select that code set. However, in some cases you may want to adjust the settings.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX ii. Network This section allows you to manually configure how your @TV interacts with your home network. 1. Radio Here you can adjust how your @TV uses its Wi-Fi capabilities. a. Ad-Hoc vs. Client Mode vs. Radio Off i. Select the mode appropriate to your network setup; Radio Off means Wi-Fi is turned off ii. Most setups will only use Client Mode b. SSID i.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX iii. Admin 1. Password change: allows you to change your @TV’s password 2. Client IP Settings – Manual Configuration This is for advanced network users to give your @TV a specific IP address and/or DNS server address.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX iv. Update 1. Software a. Use the version of your @TV setup software for troubleshooting and also automatically update it to the latest version. 2. Firmware a. Firmware is the software code that runs inside your @TV box. We recommend that you allow it to automatically check for updates every day.
CONNECTING TO YOUR CABLE OR SATELLITE SET-TOP BOX v. Info 1. Summary of your current @TV setup. This information is useful for any troubleshooting that is necessary as it provides key info about your configuration. All of the sections except the “Ports” tab are for information only. 2. Ports a. Allows you to test to see whether your Port Forwarding settings are correct and working properly. b.
ACCESSING YOUR TV, ANYWHERE 3. Accessing your TV, Anywhere d. Other issues: who controls the TV? i. When you use @TV you will be taking control of your living-room cable of satelitte box. If someone else is watching and you change the channel, he or she will be watching right along with you. a. General overview i. S imply put, @TV takes the video and audio signals from your cable or satellite box and sends them over the Internet to your phone, tablet, or computer. b. Out of home i.
© 2012 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed.
