Wi-Fi® Camera with Night Vision NETCAM User Manual F7D7601V1 • 8820-01175 Rev.
TABLE OF CONTENTS Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Troubleshooting, Support, and Warranty . . . . . . . . . . . . . . . . . . . . . . . . 28 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GETTING STARTED Initial Setup Congratulations on buying a Belkin NetCam. This device will enable you to easily check in on your home and your loved ones when you are away. To get started, you will need: What’s in the Box • Your wireless router, its network name (SSID), and password. NetCam • An Android™ device (Version 2.2 or later) or an iPhone, iPad, or iPod touch (iOS Version 4.1 or later).
GETTING STARTED Set Up Your Camera Wirelessly Through Your Mobile Devices 2. Switch the NetCam to Setup Mode by flipping up the switch on the back of the camera 1. Plug the NetCam into a power outlet Please make sure the switch is in setup mode and the Wi-Fi light is blinking.
GETTING STARTED 3. Download the NetCam App from the App Store or Google Play 4. Set Up on iPhone, iPad, or iPod touch 4.1 Connect your mobile device to NetCam Wi-Fi signal Go to “Settings > Wi-Fi” on your iPhone/iPad/iPod touch and connect to the camera’s Wi-Fi signal.
GETTING STARTED 4.2 Launch the NetCam App 4.3 Camera Setup Once your device establishes a connection with the camera, launch the NetCam App. You should see a pop-up message like the one below. Click “Yes” to set up your camera. Click “Continue” to begin setup.
GETTING STARTED 4.4 Camera Preview 4.5 Connect to Internet The camera will show you a preview after successfully connecting to your device. Choose your Wi-Fi network to connect to the Internet. Click “Connect Camera to Internet.” You may also choose to connect to your network via Ethernet cable (not included) by clicking “Ethernet.
GETTING STARTED 4.6 Connect to Internet Please wait for the camera to establish connection with the Internet. Enter your Wi-Fi password if you have a security-enabled network.
GETTING STARTED 4.7 Create an Account 4.8 Use Existing Account If this is your first time setting up your camera, you will need to create an account. If you have an existing account, select “Use Existing” and then enter your account information. Click “Sign in.
GETTING STARTED 4.9 Set Up Camera Info Click “Continue.” It will take a few seconds to register the camera with the server. Create the camera name and its description.
GETTING STARTED Congratulations ! 4.10 Setup Complete Please flip the setup switch down on the back of the NetCam. Click “Finish” to complete the setup.
GETTING STARTED 5. Set Up on Android Devices 5.2 Launch NetCam App! 5.1 Connect your device to NetCam Wi-Fi signal Once your device establishes a connection with the camera, launch the NetCam App. You should see a pop-up message like the one below. Click “Yes” to set up your camera. Go to “Settings > Wireless” and “Network > Wi-Fi settings” and connect to the camera Wi-Fi signal.
GETTING STARTED 5.3 Camera Setup 5.4 Camera Preview Click “Continue” to begin setup. The camera will show you a preview after successfully connecting to your device. Click “Connect camera to Internet.
GETTING STARTED 5.5 Connect to the Internet 5.6 Connect to Internet Choose your Wi-Fi network to connect to the Internet. Enter your Wi-Fi password if you have a security-enabled network. You may also choose to connect to your network via Ethernet cable (not included) by clicking “Ethernet.
GETTING STARTED Please wait for the camera to establish an Internet connection. 5.7 Create an Account If this is your first time setting up your camera, you will need to create an account.
GETTING STARTED 5.8 Use Existing Accounts 5.9 Set Up Camera Info If you have an existing account, select “Use Existing” and then enter your account information. Click “Sign in.” Create the camera name and its description.
GETTING STARTED Click “Continue.” It will take a few seconds to register the camera with the server. 5.10 Setup Complete Please flip the setup switch down on the back of the NetCam. Click “Finish” to complete the setup.
GETTING STARTED Congratulations! 16
GETTING STARTED 6. Mounting Your Camera (optional) Unscrew camera post from the base and remove weight. Attach screws to wall and hang plate onto screws. 1/8 in. or 5.5mm 2.
GETTING STARTED Align base with plate and screw on camera post.
GETTING TO KNOW YOUR Wi-Fi CAMERA Front Panel A: Brightness sensor B: Camera sensor C: IR LED D: Microphone 19
GETTING TO KNOW YOUR Wi-Fi CAMERA Back Panel B: C: Network Green: Connected to server Amber: Connected to local area network only Flashing Amber: Not connected to any network Flashing Green: Connected to network, ready to set up Power Green: Power On D: RJ45 port: Can be used for wired setup and for a wired connection with the router while using the NetCam. E: Camera holder You can adjust the NetCam’s position by adjusting the holder.
TECHNICAL DETAILS Technical Features • User account management • Create new user account • Reset password Software Features and Specifications App on iOS or Android • Camera setup • Live camera viewing • Save snapshot and video from the live stream • Live one-way audio • Camera settings • Enable/disable email alert • Camera sharing • Set camera status (online, offline, private) • Video stream (Frame rate, video resolution, quality) • General settings • Reset password • Sign in automatically • Invite frie
TECHNICAL DETAILS Main Window Camera Configuration • Name: Name of your camera • Share/unshare: Make your camera public to your friends or not. • Status: Change camera status to be online, offline, or private. • Rotation: Select Normal or Flipped Vertically on the videos. • IR: Select “Auto,” “On,” or “Off” of IR LEDs. • Frame Rate: Up to 30fps • Quality: 1-5 (Best = 5) Configure Camera • Video Size: 160x120, 320x240, 640x480.
TECHNICAL DETAILS Camera Viewer Take a Snapshot Record Video Enable Microphone 23
TECHNICAL DETAILS Protection Web Browser Access this link via Internet Explorer, Netscape, Firefox, or Google Chrome: http://www.belkin.com/netcam To protect your security against a hacker, a popup message will alert you if someone else is logged into your account at the same time as you. Then you can view the camera via your PC.
TECHNICAL DETAILS Hardware Features and Specifications Camera Image Sensor VGA 1/4 inch CMOS sensor Lens Focal length: 3.1mm, F2.6 View Angle Horizontal: 64° Vertical: 48° Diagonal: 80° IR LEDs 8 IR LEDs, 850nm 8-meter illumination distance IR Mode Always on Always off Auto mode ● IR turns on when luminance decreases to about 3 lux ● IR turns off when luminance increases to about 8 lux Ambient Light Sensor Still Image Capture Support VGA and 0.
TECHNICAL DETAILS Power General System Processor: RT5350 Speed: 360MHz DRAM: 64MB Flash: 8MB Button Reset Button ● Reset system: Press less than 1 second to reset the system ● Factory default: Press and hold 20 seconds to restore the factory default settings Switch Setup mode switch: Turn setup mode on and off LEDs Setup Mode LED ● Solid Green: Setup Mode on ● Amber: In progress to switch to Setup Mode ● No light: Setup Mode off Network LED ● Solid Amber: Local network ok ● Solid Green: Conne
TECHNICAL DETAILS System Requirements Resetting the Camera iPhone, iPad, or iPod touch with iOS 4.1 or above or Android smart devices Version 2.2 or above The “Reset” button is used in rare cases. In the unlikely event that your camera functions improperly, please use a pin to reset the camera. The Reset button is where the arrow below points. Reset the camera when the switch is in “OFF” mode. After the reset, the camera will resume to the default setting.
TROUBLESHOOTING, SUPPORT, AND WARRANTY If I buy more cameras, could I use the same username to connect them? How can I share my cameras with my friends? Log in to your account. Under the camera configuration, find the “Sharing” icon. Type in your friends’ email addresses to invite them to see your camera. Unlimited cameras can be added under your own account, but each one should have a different camera name. The figure below shows that you can have different cameras under your account.
TROUBLESHOOTING, SUPPORT, AND WARRANTY How can I upgrade the firmware? Can I change my username? Access your NetCam’s account from a web browser. Under the camera configuration, a screen will pop up like the one below. Click “Update Now.” It will take about 5~10 minutes to upgrade the new firmware. Your username is what identifies your account information, and once set, it cannot be changed. If you later do not like your username, the only recourse is to create a new account.
TROUBLESHOOTING, SUPPORT, AND WARRANTY Belkin International, Inc., Limited 2-Year Product Warranty What is not covered by this warranty? All above warranties are null and void if the Belkin product is not provided to Belkin for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampered with.
TROUBLESHOOTING, SUPPORT, AND WARRANTY How to get service. To get service for your Belkin product you must take the following steps: 2. Your Belkin Customer Service Representative will then instruct you on how to forward your receipt and Belkin product and how to proceed with your claim. 1. Contact Belkin International, Inc., at 12045 Waterfront Drive, Los Angeles, CA 90094, Attn: Customer Service, or call (800)-223-5546, within 15 days of the Occurrence.
TROUBLESHOOTING, SUPPORT, AND WARRANTY How state law relates to the warranty. THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
REGULATORY INFORMATION DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY • Reorient or relocate the receiving antenna. • Increase the distance between the equipment and the receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. We, Belkin International, Inc., of 12045 E.
© 2012 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Windows, Windows Vista, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. iPad, iPhone, iPod touch, Mac OS, and Safari are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Wi-Fi is a registered trademark of the Wi-Fi Alliance.
