Submittal Sheet

SCHEDULE
SUBMITTAL
A-120H
JOB: REPRESENTATIVE:
UNIT TAG: ORDER NO. DATE:
ENGINEER:
SUBMITTED BY: DATE:
CONTRACTOR:
APPROVED BY:
DATE:
Iron & Lead-Free
†
Bronze
*
Booster Pump
*
Where potable water is supplied, use a lead-free
†
bronze pump.
DESCRIPTION
Bell & Gossett in-line three-piece booster pumps are designed
for hydronic systems. Series 100 and HV are Listed with
Underwriter's Laboratories.
CONSTRUCTION
Body: Cast Iron or Lead-Free
†
Bronze
Seal: Mechanical, Carbon on Ceramic
OPERATIONAL DATA
Maximum Working Pressure: 125 PSI (682 kPa)
Maximum Operating Temperature:
- Standard Seal: 225°F (107°C) continuous
- Special Seals: 250°F (121°C) continuous (consult local B&G Representative)
Maximum Motor RPM: 1750
Shaft: Carbon Steel, Heat Treated
Pump and Motor Bearings:
−All except PD-38 and PD-40: Bronze Sleeve, Oil Lubricated
−PD-38 and PD-40: Ball Bearing, Permanently Lubricated
Coupler:
−All except PD38 and PD40: Flexible, Spring type
−PD38 and PD40: Flexible, sleeve type.
Motor: Bell & Gossett 1/12 hp thru 1-1/2 hp standard single and three phase drip-
proof motors are Recognized under the Component Program of Underwriter's
Laboratories, Inc. Bell & Gossett boosters with their respective Bell & Gossett
manufactured standard 60 hertz single and three phase motors are Certified by
CSA.
IMPELLER:
PUMP MODEL NO. IRON BOD
Y
BRONZE BODY
Series 100® Pump
Polypropylene* or Lead-Free
†
Brass
Polypropylene* or
Lead-Free
†
Brass
Series HV & 2
Phenolic* or Lead-Free
†
Brass
Phenolic* or Lead-
Free
†
Brass
PR, 2-1/2, LD3
Steel, Zinc Plated or Lead-Free
†
Brass
Lead-Free
†
Brass
HD3, PD35, PD37
Steel, Zinc Plated or Lead-Free
†
Brass
Lead-Free
†
Brass
PD38 & PD40
Cast Iron or Lead-Free
†
Brass Lead-Free
†
Brass
* System temperatures above 225 °F (107 °C) require a brass impeller.
†
Contains less than 0.25% Lead content by weight on wetted surfaces.
MODEL
NO.
FLANGE
SIZE NPT
INCHES
**STANDARD 60 CYCLE CHARACTERISTICS
TAGGING INFORMATION
QUANTIT
Y
HP PH
V
OLTAGE
*
F.L. AMPS RPM
Iron Body Bronze Body
STD BI BI NFI
Series 100
3/4, 1,
1-1/4 & 1-1/2
1/12 1 115 1.75 1725
Series PR
3/4, 1,
1-1/4 & 1-1/2
1/6 1 115 1.9 1725
−
Series HV
1, 1-1/4
& 1-1/2
1/6 1 115 1.9 1725
2 2 1/6 1 115 1.9 1725
2-1/2 2-1/2 1/4 1 115 3.0 1725
−
LD3 3 1/4 1 115 3.0 1725
−
HD3 3 1/3 1 115/230 4.2/2.1 1725
−
PD-35S 3 1/2 1 115/230 5.2/2.6 1725
−
PD-35T 3 1/2 3 208-230/460 1.8-1.7/.85 1750
−
PD-37S 3 3/4 1 115/230 7.0/3.5 1725
−
PD-37T 3 3/4 3 208-230/460 2.45-2.4/1.2 1750
−
PD-38S 3 1 1 115/230 9.8/4.5 1725
−
PD-38T 3 1 3 208-230/460 3.4-3.4/1.7 1725
−
PD-40S 3 1-1/2 1 115/230 18.0/9.0 1725
−
PD-40T 3 1-1/2 3 208-230/460 4.8-4.8/2.4 1725
−
**Motors with special electrical characteristics are available on request at additional cost.
*
1 PH Motors: Built-in overload protection
3 PH Motors: Overload protection must be provided
Bell & Gossett Booster Pumps equipped with a drip-proof motor are recommended for indoor use only.