Submittal Sheet

Iron & Bronze Booster Pump Submittal A-120H
MODEL
NO.
FLANGE
SIZE NPT
INCHES
DIMENSIONS IN INCHES
(
MM
)
A
PPROX. SHPG.
WT. LBS.
(
K
g)
A B C
IRON
BODY
BRONZE
BOD
Y
Series 100
3/4, 1,
1-1/4 & 1-1/2
14-7/8
(378)
6-3/8
(162)
12-3/4
(324)
20
(9)
21
(10)
Series PR
3/4, 1,
1-1/4 & 1-1/2
15-1/4
(387)
8-1/2
(216)
12-3/4
(324)
30
(14)
32
(15)
Series HV
1,
1-1/4 & 1-1/2
15-3/8
(391)
8-1/2
(216)
13
(330)
28
(13)
30
(14)
2 2
16-5/8
(422)
8-1/2
(216)
14
(356)
36
(16)
39
(18)
2-1/2 2-1/2
17-1/4
(
438
)
10
(
254
)
14
(
356
)
54
(
24
)
58
(
26
)
LD3 3
17-1/4
(
438
)
10
(
254
)
14
(
356
)
53
(
24
)
57
(
26
)
HD3 3
17-1/2
(
444
)
10
(
254
)
14-1/4
(
362
)
55
(
25
)
59
(
27
)
PD-35S 3
20-1/4
(
514
)
12
(
305
)
16-7/8
(
429
)
75
(
34
)
80
(
36
)
PD-35T 3
20-1/4
(514)
12
(305)
16-7/8
(429)
75
(34)
80
(36)
PD-37S 3
20-1/4
(514)
12
(305)
16-7/8
(429)
75
(34)
80
(36)
PD-37T 3
20-1/4
(514)
12
(305)
16-7/8
(429)
75
(34)
80
(36)
PD-38S 3
22-11/16
(576)
14-1/2
(368)
18-15/16
(481)
128
(58)
138
(63)
PD-38T 3
23-15/16
(608)
14-1/2
(368)
20-3/16
(513)
125
(57)
135
(61)
PD-40S 3
24-3/4
(629)
14-1/2
(368)
21
(533)
130
(59)
140
(64)
PD-40T 3
21-7/8
(556)
14-1/2
(368)
18-1/8
(460)
127
(58)
137
(62)
Dimensions are subject to change.
Not to be used for construction purposes unless certified.
TYPICAL SPECIFICATIONS
Electrical Box Arran
g
ement for pumps with B&G Manufactured Motors
MODEL
NO. #1 #2 #3 #4
Series 100
115 & 230Volt 60Hz 1PH
110 & 220Volt 50Hz 1PH
− − −
Series HV, PR & 2
115 & 230Volt 60Hz 1PH
110 & 220Volt 50Hz 1PH
− 3PH −
2-1/2", LD3 & HD3 − 1PH − −
PD35 & PD37 − − ALL −
PD38 & PD40 − − − ALL
The Contractor shall furnish and install In-The-Line pumps as illustrated on the
plans and in accordance with the following specifications:
1. The pumps shall be of the horizontal, oil-lubricated type. (Except PD-38, PD-
40 are permanently lubricated) Specifically designed and guaranteed for quiet
operation. Suitable for 125# (862 kPa) working pressure.
2.The pumps shall have a ground and polished steel shaft with a hardened
integral thrust collar. The shaft shall be supported by two horizontal sleeve
bearings designed to circulate oil. (Except PD-38, PD-40 are grease lubricated
ball bearing design) The pumps are to be equipped with a mechanical seal with
carbon seal face rotating against a ceramic seat. The motor shall be non-
overloading at any point on pump curve.
3. The motor shall be of the drip-proof, sleeve-bearing, (Except PD-38, PD-40
are ball bearing) quiet operating, rubber-mounted construction. Motors shall
have built-in thermal overload protectors. (Exception - PD models with 3-phase
motors, see paragraph 4.)
4. For PD models with 3-phase motors, add the following: The Contractor shall
furnish and install a magnetic starter for each booster pump with at least two
thermal overload protectors. The starter shall be equipped with manual reset
buttons.
A
ll Units must be ITT Bell & Gossett Model No. ________, or approved equal
with capacity of ______GPM at ______ft. head when directly driven through a
self aligning flexible coupling by an oil lubricated motor, _____volts
_
___c
y
cle___phase.
Xylem Inc.
8200 N. Austin Avenue
Morton Grove, IL 60053
Phone: [phone]
Fax: [phone]
www.xyleminc.com/brands/bellgossett
Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.
© 2012 Xylem Inc.