Instruction Manual

ManualsBrandsBell & Gossett ManualsPumpsDN0130D Domestic Pump 250°F Condensate Units Series SA-PT

INSTRUCTION MANUAL

DN0130

REVISION D

Domestic

Pump

250˚F Condensate Units

Series SA

™

and SA-P

™

SAFETY



INSTRUCTIONS



This safety alert symbol will be used in this manual and on

the unit safety instruction decals to draw attention to safety

related instructions. When used, the safety alert symbol means

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT

IN A SAFETY HAZARD.

If the decals are missing or are illegible contact your local B&G

representative for a replacement.

1. Electrical connections to be made by a qualified Electrician

in accordance with all National, State and Local codes.

2. Motor must have properly sized starter with properly sized

heaters to provide overload and undervoltage protection.

3. If pump, motor or piping are operating at extremely high or

low temperatures, guarding or insulation is required.

4. Operating personnel should be trained in the operation of

condensate return units.

CAUTION

DO NOT RUN PUMP DRY,

SEAL DAMAGE MAY OCCUR.

INSPECT PUMP SEAL



REGULARL

Y FOR LEAKS,



REPLACE AS REQUIRED

FOR LUBRICATION



REQUIREMENTS,

CONSULT



SERVICE INSTR

UCTIONS.

FAILURE TO FOLLOW



INSTR

UCTIONS COULD



RESUL

T IN INJURY OR



PROPER

TY DAMAGE.

P70644



Morton Grove, Illinois 60053



SERIES

MODEL

SERIAL

GPM PSI PUMP

CFM IN HG. PUMP

DWGS

POWER V. PH. HZ60

CONTROL V. PH. 1 HZ60

TOTAL LARGEST MOTOR

F.L. AMP F.L. AMP

DN0016



Morton Grove, Illinois 60053



SERIES

MODEL

SERIAL

GPM PSI PUMP

POWER V. PH. HZ60

CONTROL V. PH. 1 HZ60

TOTAL LARGEST MOTOR

F.L. AMP F.L. AMP

DOMESTIC

PUMPS

WARNING

DO NOT EXCEED PRESSURE

RATING OF THE UNIT.

DO NOT ALTER OR DEFEAT



PRESSURE RELIEF V

ALVE.

OPEN VALVES SLOWLY.

MAXIMUM PRESSURE 15 PSI.

FAILURE TO FOLLOW



INSTR

UCTIONS COULD



RESUL

T IN INJURY OR



PROPER

TY DAMAGE.

DN0124



EXPLOSIBLE

INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER’S USE.



SERIES SA-P

™



SERIES SA

™



DN0124 ALL UNITS



DN0016 UNITS PANEL



P70644 ALL UNITS



DN0019 UNITS LESS PANEL



Summary of content (8 pages)

PAGE 1
INSTRUCTION MANUAL DN0130 REVISION D Domestic® Pump 250˚F Condensate Units Series SA™ and SA-P™ SERIES SA-P ™ SERIES SA ™ INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER’S USE. WARNING SAFETY INSTRUCTIONS EXPLOSIBLE DO NOT EXCEED PRESSURE RATING OF THE UNIT. DO NOT ALTER OR DEFEAT PRESSURE RELIEF VALVE. OPEN VALVES SLOWLY. MAXIMUM PRESSURE 15 PSI. FAILURE TO FOLLOW INSTRUCTIONS COULD RESULT IN INJURY OR PROPERTY DAMAGE.
PAGE 2
High Temperature Condensate Units Series SA and SA-P REPRESENTATIVE PIPING DIAGRAMS STEAM ABSORPTION UNIT OR CONVERTER OR FAN COIL UNIT OR STEAM PROCESS EQUIPMENT COMPOUND GAUGE PRESSURE RELIEF VALVE, PIPE TO DRAIN (PITCH DOWN) PROPORTIONING REGULATOR MECHANICAL DRAIN VALVE (OPTIONAL) GAUGE GLASS FLOAT SWITCH FOR STAND BY THERMOSTATIC VENT TRAP ANODE DIAL TEMP. GAUGE TO DRAIN DOMESTIC SERIES B35 CENTRIFUGAL PUMP (SERIES DB PUMP OPT.
PAGE 3
CAUTION: UNIT LIFTING EYE Use unit lifting eyes only to lift unit as shipped from factory. Unit must be empty and disconnected from pipes, anchors and other restraints. Use proper rigging procedures. Failure to follow these instructions could result in injury or property damage. LOCATION Place unit for easy access to all parts. Allow adequate space for servicing. Check ambient conditions. NOTICE / TEMPERATURE LIMITS Motors are designed to operate in 104°F (40°C) max. ambient.
PAGE 4
Three phase motors must use starters with properly sized overload relays. Overload relays furnished are designed for manual reset. A variety of electrical controls are available to meet system specifications. Wiring diagrams are enclosed in electrical panels when the panels are furnished as part of the unit. INSULATION Series SA units frequently handle condensate at temperatures up to 250°F (121°C).
PAGE 5
MAINTENANCE PROCEDURE FOR RED LINE GAGE GLASS WARNING: EXPLOSIBLE Improper installation or maintenance of tubular glass can cause immediate or delayed glass breakage resulting in bodily injury. To avoid breakage observe the following Do’s and Do Not’s and Use and Care Instructions, as well as tubular gage manufacturer’s instructions. If a gage glass breaks, contained substances can be released and glass can be blown out of the unit with great force.
PAGE 6
1. Hold fittings rigidly to prevent misalignment, which can cause severe bending stresses in the glass, when packing nuts are tightened. 6. Tighten packing nuts enough to prevent leakage, but not so much that you hinder expansion and contraction. Follow gage manufacturer’s recommendations. 2. Provide metal washers so nuts can be tightened without twisting packing or tube. 7. Generally, you can use cylindrical or conical rubber packings for LOW and MEDIUM pressures.
PAGE 7
DEALER SERVICING TM If trouble occurs that cannot be rectified, contact your local B&G representative. He will need the following information in order to give you assistance. TM SERIES MODEL SERIAL 1. Complete nameplate data of pump and motor. SEE RATING NAMEPLATE. 2. Suction and discharge pipe pressure gauge readings. GPM PSI PUMP CFM IN HG. PUMP DWGS 3. Ampere draw of the motor. 4. A sketch of the pump hook-up and piping. POWER V. PH. HZ60 CONTROL V. PH. 1 HZ60 DN0016 TOTAL F.L.
PAGE 8
Xylem Inc. 8200 N. Austin Avenue Morton Grove, Illinois 60053 Phone: (847) 966-3700 Fax: (847) 965-8379 www.xyleminc.com/brands/bellgossett Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. © 2012 Xylem Inc.