7610 7612 FLAT PANEL TV WALL MOUNT INSTRUCTION MANUAL SUPPORT MURAL D'ÉCRAN PLAT MANUEL D'INSTRUCTIONS SOPORTE DE PARED PARA TV DE PANTALLA PLANA MANUAL DE INSTRUCCIONES SUPPORTO A PARETE PER TELEVISORE A SCHERMO PIATTO MANUALE DI ISTRUZIONI WANDBEFESTIGUNG FÜR FLACHBDILDSCHIRM5TV ANLEITUNGSHANDBUCH НАСТЕННЫЙ КРОНШТЕЙН ДЛЯ ПЛОСКОПАНЕЛЬНОГО ТЕЛЕВИЗОРА ИНСТРУКЦИЯ
PRECAUTIONS If at any time you are unclear about the directions and believe you need further assistance, contact Bell’O® at: 1-888-235-7646 (US/Canada) or +1-732-972-1333 (International) from 9am – 5pm EST. • NEVER EXCEED THE MAXIMUM LOAD CAPACITY OF 200 LBS (91 KG), • This mounting bracket was designed to be installed and utilized ONLY as specified in this manual.
AVERTISSEMENTS Pour toutes questions concernant les instructions ou pour tout besoin d'assistance, veuillez communiquer avec Bell’O® au : 1-888-235-7646 (USA/Canada) ou +1-732-972-1333 (International) de 9h00 à 17h00 (heure de l'Est). • NE JAMAIS DÉPASSER LA CAPACITÉ DE CHARGE MAXIMALE DE 91 KG (200 LBS). • Ce support de fixation est conçu pour être posé et utilisé UNIQUEMENT comme indiqué dans ce manuel.
ADVERTENCIAS Si en algún momento tiene dudas sobre las instrucciones y necesita asesoramiento adicional, comuníquese con Bell’O®: 1-888-235-7646 (EE. UU. y Canadá) o +1-732-972-1333 (desde otros lugares del mundo) de 9 a 17 hora del este. • NUNCA EXCEDA LA CAPACIDAD MÁXIMA DE CARGA DE 200 LBS (91 KG). • Este soporte fue diseñado para ser instalado y utilizado ÚNICAMENTE como se indica en el presente manual.
PRECAUZIONI Nel caso che, in qualsiasi momento, le istruzioni non dovessero risultare chiare o si necessitasse di ulteriore assistenza, contattare Bell’O® al numero verde: 1-888-235-7646 (da USA/Canada) oppure al +1-732-972-1333 (da altri Paesi) dalle 9.00 - 17.00 (ora costa orientale USA). • NON SUPERARE MAI LA MASSIMA CAPACITÀ DI CARICO, PARI A 91 KG. • Questo supporto è stato progettato UNICAMENTE per essere installato e utilizzato come specificato in questo manuale.
VORSICHTSMASSNAHMEN Sollten Sie sich nicht ganz klar über die Anleitungen und der Ansicht sein, dass Sie Unterstützung brauchen, setzen Sie sich bitte mit Bell’O® unter Telefonnummer 1-888-235-7646 (US/Kanada) oder + 1-732-972-1333 (International) zwischen 9 Uhr und 17 Uhr (Ostzeit) in Verbindung. • BITTE NIE DIE HÖCHSTBELASTBARKEIT VON 91 KG (200 PFD) ÜBERSCHREITEN. • Diese Konsole darf NUR so wie in diesen Anleitungen beschrieben installiert und verwendet werden.
ПРЕДУПРЕЖДЕНИЕ Если вам понадобится помощь или что–то непонятно в инструкции, обратитесь в фирму Bell’O® по телефону 1-888-235-7646 (США/Канада) или +1-732-972-1333 (для международных звонков) с 9 утра до 5 вечера (время — восточное стандартное). • НИ ПРИ КАКИХ ОБСТОЯТЕЛЬСТВАХ НЕ ПРЕВЫШАТЬ МАКСИМАЛЬНУЮ НАГРУЗКУ В 200 ФУНТОВ (91 КГ). • Этот настенный кронштейн был сконструирован для установки и использования ТОЛЬКО в соответствии со спецификациями, приведенными в этом документе.
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (WP) Wall Plate, 1 Plaque murale, 1 Placa de pared, 1 Supporto a parete, 1 Wandplatte, 1 Настенная плата, 1 (MA) Monitor Arms, 2 Bras de moniteur, 2 Brazos de la pantalla, 2 Snodi dello schermo, 2 Monitorarme, 2 Крепежные узлы монитора, 2 (TA) 5° Tilt Adapters (7612 Only), 4 Adaptateurs d'inclinaison de 5° (7612 seulement), 4 Adaptadores de inclinación de 5° (7612 solamente), 4 Adatta
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (A) M4 x 12mm, 4 (B) M4 x 22mm, 4 (C) M4 x 30mm, 4 (AB) M4 x 10mm, 2 (AE) M6 (7612 Only), 4 M6 (7612 seulement), 4 M6 (7612 solamente), 4 M6 (solo modello 7612), 4 M6 (Nur 7612), 4 M6 (только для модели 7612), 4 (G) M5 x 12mm, 4 (H) M5 x 22mm, 4 (I) M5 x 30mm, 4 10 (AC) M6 (7612 Only), 4 Boulon à tête bombée (7612 seulement), 4 Pernos de cabeza redonda con cuello cuadrado (7612
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (D) M4/M5, 4 (E) M4/M5, 4 (Q) M6/M8, 4 (P) M6/M8, 4 (R) M4/M5, 4 (S) M6/M8, 4 (U) TOGGLER® brand AF8 ALLIGATOR® Anchor, 4 (T) #14 x 65mm, 4 TOGGLER® brand ALLIGATOR® SOLID-WALL ANCHORS are patented under one or more of US Patent numbers 5,161,296 and 5,938,385; and foreign counterparts thereof and of 4,752,170. Other patents pending.
NECESSARY TOOLS OUTILLAGE NÉCESSAIRE HERRAMIENTAS NECESARIAS ATTREZZI NECESSARI ERFORDERLICHE WERKZEUGE НЕОБХОДИМЫЕ ИНСТРУМЕНТЫ Phillips-head Screwdriver Tournevis à tête Phillips Destornillador philips (cruz) Cacciavite Phillips Kreuzschlitzschraubenzieher Крестообразная отвертка Masking Tape Ruban de masquage Cinta de enmascarar Nastro adesivo Abdeckband Маскировочная лента Ratchet Set Clé à cliquet à douilles Equipo de trinquete Strumento Del Cricco Schaltklinke Hilfsmittel Набор инструментов с храпов
ATTACHING THE MONITOR ARMS (MA) FIXER LES BRAS DE MONITEUR (MA) CÓMO FIJAR LOS BRAZOS DE LA PANTALLA (MA) FISSAGGIO DEGLI SNODI DELLO SCHERMO (MA) BEFESTIGUNG DER MONITORARME (MA) ПРИКРЕПЛЕНИЕ КРЕПЕЖНЫХ УЗЛОВ МОНИТОРА (МА) SELECT THE CORRECT SCREW Before beginning, test several of the screws in your hardware kit to find the correct size and length for your television.
USING THE 5° TILT ADAPTER (7612 ONLY) If you will be mounting your TV above eye level, and would prefer your mounted TV with a slight tilt, insert two Carriage Bolts (AC) into each Monitor Arm (MA) as shown. Secure them with M6 Nuts (AE). Repeat for other arm. Make sure the finished head of the Carriage Bolt will be on the outside of the Monitor Arm so the M6 Nuts will not be seen once the TV is installed.
ATTACHING THE MONITOR ARMS (MA) Attach each Monitor Arm (MA) to the back of your television as shown. Make sure that each Washer (R for M4 or M5 screws, or S for M6 or M8 screws) is placed between the Screw and the Monitor Arm. Don’t place the Washers between the Arms and the television. FIXER LES BRAS DE MONITEUR (MA) Fixer les deux bras de moniteur (MA) au dos du téléviseur comme sur l'illustration.
Use spacers if Monitor Arms (MA) do not fit firmly against the back of the television, such as when the back of the television is curved, contains larger recessed mounting holes, or some other obstruction is in the way. Spacers also provide extra room for cables. The Arms must rest securely on the spacers, and should not be loose.
INSTALLING THE WALL MOUNT IN WOOD POSER LE SUPPORT MURAL SUR DU BOIS CÓMO INSTALAR EL SOPORTE DE PARED EN MADERA INSTALLAZIONE DEL SUPPORTO A PARETE SU LEGNO INSTALLATION DER WANDBEFESTIGUNG IN HOLZ КРЕПЛЕНИЕ НАСТЕННОГО КРОНШТЕЙНА К ДЕРЕВУ FIND THE WOOD STUDS Using a stud finder, find the exact location of the studs to which you want to attach the wall mount. Mark the right and left side to determine the center of each stud.
DETERMINE HEIGHT LOCATION OF TELEVISION Measure the distance from the bracket holes to the top and bottom of the TV to determine the center mounting position. Measure from the floor up, and make small marks on the wall to help you determine the desired TV height. Using a level, line up the Installation Template (IT) with your pencil markings and tape it into place.
IT • Height to bottom of TV • Hauteur jusqu'au bas du téléviseur • Altura hasta la parte inferior del TV • Altezza alla parte inferiore del televisore • Höhe zum unteren Teil des TVs • Высота до низа телевизора 19
INSTALL THE SECURITY SCREWS (AB) Before you attach the Wall Plate (WP) to the wall, insert the M4 x 10mm Security Screws (AB) into the locking mechanism on each end of the bracket. Insert them only half way, so that the locking arm can still be easily rotated. POSER LES VIS DE SÉCURITÉ (AB) Avant de fixer la plaque murale (WP) au mur, introduire les vis de sécurité M4 x 10 mm (AB) dans le mécanisme de verrouillage à chaque extrémité de la plaque.
WP AB FOR MASONRY INSTALLATIONS, SEE PAGE 25. POUR UNE POSE SUR DE LA MAÇONNERIE, VOIR PAGE 25. PARA INSTALACIONES EN MAMPOSTERÍA CONSULTE LA PÁGINA 25. PER INSTALLAZIONI A MURO, VEDERE A PAGINA 25. FÜR INSTALLATIONEN IN MAUERWERK, SIEHE SEITE 25. КРЕПЛЕНИЕ К КАМЕННОЙ КЛАДКЕ, СМ. СТР. 25.
DRILL PILOT HOLES Follow directions on the Installation Template (IT) carefully. Drill four holes 2.5" (64mm) deep using a 5/32" (or 4mm) size drill bit in the “A”, “B”, "C", and "D" locations noted on the Installation Template. PERCER LES TROUS GUIDES Suivre avec attention les instructions figurant sur le gabarit de pose (IT). Percer quatre trous de 64 mm (2,5 po) de profond avec un foret de 5/32 po (ou 4 mm) de diamètre aux emplacements notés « A », « B », « C » et « D » sur le gabarit de pose.
A C B D Use lines on Installation Template (IT) to align Template with stud pencil markings. Se servir des lignes sur le gabarit de pose (IT) pour aligner le gabarit avec repères de montants au crayon. Utilice líneas en la plantilla de instalación (IT) para alinear la plantilla con las marcas de lápiz en el montante. Utilizzare le linee presenti nello schema di installazione (IT) per allineare lo schema stesso ai segni fatti in matita.
INSTALL THE WALL PLATE (WP) After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
MOUNTING TO SOLID CONCRETE, BRICKS, OR CINDER BLOCK POSE SUR DU BÉTON PLEIN, DES BRIQUES OU DES PARPAINGS MONTAJE EN CONCRETO SÓLIDO, LADRILLO O LADRILLOS DE ESCORIAS MONTAGGIO SU CALCESTRUZZO, MATTONI O BLOCCHI IN CEMENTO MONTAGE AN FESTBETON, MAUERZIEGELN ODER SCHLACKENBETONBLOCK КРЕПЛЕНИЕ К НЕАРМИРОВАННОМУ БЕТОНУ, КИРПИЧУ ИЛИ ШЛАКОБЕТОННОМУ БЛОКУ After you have determined your desired TV location, Line up the Installation Template (IT) to ensure you will not drill into any mortar joints.
DRILL PILOT HOLES Follow directions on the Installation Template (IT) carefully. Carefully drill four holes using a 5/16" (or 8mm) masonry drill bit in the “A”, “B”, "C", and "D" locations noted on the Installation Template. Each hole should be at least 3" (76mm) deep. PERCER LES TROUS GUIDES Suivre avec attention les instructions figurant sur le gabarit de pose (IT).
U INSERT ANCHORS Remove Template (IT) and insert TOGGLER® brand ALLIGATOR® Anchors (U). ENFONCER LES CHEVILLES Enlever le gabarit (IT) et enfoncer des chevilles d'ancrage ALLIGATOR® de la marque TOGGLER® (U). COLOQUE LOS ANCLAJES Quite la plantilla (IT) y coloque los anclajes (U) marca TOGGLER® Y ALLIGATOR®. INSERIRE I TASSELLI Togliere lo schema (IT) e inserire i tasselli ALLIGATOR® di marca TOGGLER® (U).
INSTALL THE WALL PLATE (WP) After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
INSTALL THE DECORATIVE END COVERS (EC) Line up the two peg inserts on the back of each End Cover (EC) with the two holes at the ends of the Wall Plate (WP), and press into place. Each End Cover is marked with a "L" (for Left side) or "R" (for Right side). POSER LES CAPUCHONS DÉCORATIFS (EC) Aligner les deux chevilles au dos de chaque capuchon (EC) avec les deux trous aux extrémités de la plaque murale (WP) et les enfoncer en place. Les capuchons sont marqués « L » (côté gauche) ou « R » (côté droit).
MOUNTING THE TELEVISION POSE DU TÉLÉVISEUR CÓMO INSTALAR EL TELEVISOR MONTAGGIO DEL TELEVISORE MONTAGE DES FERNSEHERS УСТАНОВКА ТЕЛЕВИЗОРА UNDERSTANDING THE LOCKING MECHANISM The Locking Mechanism locks the Monitor Arms (MA) onto the Wall Plate (WP) to prevent television removal. Before attempting to attach the television with the Monitor Arms to the Wall Plate, make sure that the Locking Mechanism is in the unlocked position.
To Unlock Déverrouiller Para destrabar Per sbloccare Entriegelung Чтобы разблокировать Locking Bar Shown Up in Unlocked Position Barre de verrouillage représentée en position haute déverrouillée Large Screw Head Grande tête de vis Punta del tornillo grande Vite a testa grande Großer Schraubkopf Большая головка винта Barra de cierre en posición destrabada.
MOUNT THE TELEVISION With the help of an assistant, lift the television and guide the Monitor Arms (MA) onto the Wall Plate (WP) as shown. POSER LE TÉLÉVISEUR Avec l'aide d'une autre personne, soulever le téléviseur et guider les bras de moniteur (MA) dans plaque murale (WP) comme sur l'illustration. CÓMO MONTAR EL TELEVISOR Con la ayuda de un asistente, levante el televisor y guíe los brazos de la pantalla (MA) sobre la placa de pared (WP) tal como se muestra.
MA WP MAKE SURE BOTH MONITOR ARMS (MA) ARMS ARE ENGAGED ON BOTH THE TOP AND BOTTOM RAILS OF THE WALL PLATE (WP)! S'ASSURER QUE LES DEUX BRAS DE MONITEUR (MA) SONT ENGAGÉS À LA FOIS SUR LES RAILS SUPÉRIEUR ET INFÉRIEUR DE LA PLAQUE MURALE (WP). ASEGÚRESE DE QUE AMBOS BRAZOS DE LA PANTALLA (MA) SE ENGANCHEN EN LOS RIELES SUPERIOR E INFERIOR DE LA PLACA DE PARED (WP).
SECURE THE TELEVISION After the television with the Monitor Arms (MA) is attached to the Wall Plate (WP), lock the Arms into place to prevent removal of the television. To lock the Arms, simply turn the large screw head on the side of the Wall Plate 90° toward the wall using a screwdriver. Have an assistant hold the television in place while you do this.
AB To Lock Verrouiller Para trabar Per bloccare Verriegelung Чтобы заблокировать Locking Bar Shown Down in Locked Position Large Screw Head Grande tête de vis Punta del tornillo grande Vite a testa grande Großer Schraubkopf Большая головка винта Barre de verrouillage représentée en position basse verrouillée Barra de bloqueo hacia abajo en posición trabada.
LIMITED LIFETIME WARRANTY This Bell’O International, Corp. (“Bell’O” or “we”) mounting product SKU # 7610 or 7612 (“Product”) is warranted for the life of the Product only to the original purchaser and limited to the original installation (“Warranty”). Re-installation of the Product in a different location or with a different monitor or peripheral voids this Warranty. This Warranty is only valid in the United States of America and Canada.
GARANTIE À VIE LIMITÉE Ce produit de fixation Bell’O International, Corp. (« Bell’O » ou « nous ») de n° SKU 7610 ou 7612 (le « Produit ») est garanti pendant la durée de vie du Produit uniquement à l'acheteur initial et dans les limites de la pose initiale (« Garantie »). La réinstallation du Produit à un emplacement différent ou avec un téléviseur ou périphérique différent annule cette Garantie. Cette garantie est valable uniquement aux États-Unis d’Amérique et au Canada.
GARANTÍA LIMITADA DE POR VIDA Este producto de montaje SKU # 7610 o 7612 (“Producto”) Bell’O International, Corp. (“Bell’O” o “nosotros”) está cubierto por la garantía durante la vida del Producto solo para el comprador original y está limitada a la instalación original (“Garantía”). La Garantía solo es válida en los Estados Unidos de Norteamérica y Canadá.
GARANZIA LIMITATA A VITA Questo prodotto di supporto SKU # 7610 o 7612 (“Prodotto”) di Bell’O International, Corp. (“Bell’O” o “noi”) è coperto da garanzia per la durata della vita del Prodotto unicamente per l'acquirente originale e solo per l'installazione originale (“Garanzia”). La reinstallazione del Prodotto in posizione diversa, o con schermo o periferica diversi, rende questa Garanzia nulla. Questa Garanzia vale unicamente negli Stati Uniti d'America e in Canada.
BESCHRÄNKTE GARANTIE AUF LEBENSZEIT Eine Gewährleistung für dieses Montageprodukt SKU Nr. 7610 oder 7612 (das "Produkt") von Bell’O International Corporation (“Bell’O” oder “wir”) wird für die Lebenszeit des Produkts nur dem ursprünglichen Käufer gegenüber zugesichert und beschränkt sich auf die ursprüngliche Installation ("Gewährleistung"). Eine erneute Installation des Produkts an einer anderen Stelle oder mit einem anderen Monitor oder an einer anderen Außenfläche macht diese Garantie ungültig.
ОГРАНИЧЕННАЯ ПОЖИЗНЕННАЯ ГАРАНТИЯ Фирма Bell’O International, Corp. (“Bell’O” или “мы”) дает гарантию на кронштейн SKU # 7610 или 7612 (“Продукт”) на время жизни Продукта только первоначальному покупателю и только на первую установку (“Гарантия”). Повторная установка Продукта в другом месте, либо с другим монитором или с другой периферийной аппаратурой аннулирует эту Гарантию. Эта Гарантия имеет силу только в Соединенных Штатах Америки и Канаде.
NOTES NOTES NOTAS NOTE ANMERKUNGEN ПРИМЕЧАНИЯ
NOTES NOTES NOTAS NOTE ANMERKUNGEN ПРИМЕЧАНИЯ
BELL'O INTERNATIONAL CORPORATION 711 Ginesi Drive, Morganville, NJ 07751 (888) 235-7646 • (732) 972-1333 www.bello.