7745 FLAT PANEL TV WALL MOUNT INSTRUCTION MANUAL SUPPORT MURAL D'ÉCRAN PLAT MANUEL D'INSTRUCTIONS SOPORTE DE PARED PARA TV DE PANTALLA PLANA MANUAL DE INSTRUCCIONES SUPPORTO A PARETE PER TELEVISORE A SCHERMO PIATTO MANUALE DI ISTRUZIONI FLACHBILDSCHIRM TV WANDBEFESTIGUNG ANLEITUNGSHANDBUCH НАСТЕННЫЙ КРОНШТЕЙН ДЛЯ ПЛОСКОПАНЕЛЬНОГО ТЕЛЕВИЗОРА ИНСТРУКЦИЯ
PRECAUTIONS If at any time you are unclear about the directions and believe you need further assistance, contact Bell’O® at: 1-888-235-7646 (US/Canada) or +1-732-972-1333 (International) from 9am – 5pm EST. • NEVER EXCEED THE MAXIMUM LOAD CAPACITY OF: 130 LBS (59 KG) WHEN INSTALLED INTO 2 STUDS OR MASONRY INSTALLATIONS; OR 80 LBS (36.3 KG) WHEN INSTALLED INTO 1 STUD. • This mounting bracket was designed to be installed and utilized ONLY as specified in this manual.
AVERTISSEMENTS Pour toutes questions concernant les instructions ou pour tout besoin d'assistance, veuillez communiquer avec Bell’O® au : 1-888-235-7646 (USA/Canada) ou +1-732-972-1333 (International) de 9h00 à 17h00 (heure de l'Est). • NE JAMAIS DÉPASSER LA CAPACITÉ DE CHARGE MAXIMALE DE : 59 KG (130 LB) EN CAS DE POSE SUR 2 MONTANTS OU SUR UN MUR DE MAÇONNERIE, OU 36,3 KG (80 LB) EN CAS DE POSE SUR 1 MONTANT.
ADVERTENCIAS Si en algún momento tiene dudas sobre las instrucciones y necesita asesoramiento adicional, comuníquese con Bell’O®: 1-888-235-7646 (EE. UU. y Canadá) o +1-732-972-1333 (desde otros lugares del mundo) de 9 a 17 hora del este. • NUNCA EXCEDA LA CAPACIDAD MÁXIMA DE CARGA DE: 130 LB (59 KG) CUANDO SE LO INSTALA EN 2 MONTANTES O EN MAMPOSTERÍA O 80 LB (36,3 KG) CUANDO SE LO INSTALA EN 1 MONTANTE.
PRECAUZIONI Nel caso che, in qualsiasi momento, le istruzioni non dovessero risultare chiare o si necessitasse di ulteriore assistenza, contattare Bell’O® al numero verde: 1-888-235-7646 (da USA/Canada) oppure al +1-732-972-1333 (da altri Paesi) dalle 9.00 - 17.00 (ora costa orientale USA). • NON SUPERARE MAI LA MASSIMA CAPACITÀ DI CARICO DI 59 KG, NEL CASO DI INSTALLAZIONE SU DUE MONTANTI O SU MURATURA, E DI 36,3 KG, NEL CASO DI INSTALLAZIONE SU UN SOLO MONTANTE.
VORSICHTSMASSNAHMEN Sollten Sie sich nicht ganz klar über die Anleitungen und der Ansicht sein, dass Sie Unterstützung brauchen, setzen Sie sich bitte mit Bell’O® unter Telefonnummer 1-888-235-7646 (US/Kanada) oder + 1-732-972-1333 (International) zwischen 9 Uhr und 17 Uhr (Ostzeit) in Verbindung. • ÜBERSCHREITEN SIE NIE DIE HÖCHSTBELASTUNG VON: 59 KG BEI INSTALLATIONEN IN 2 BOLZEN ODER MAUERWERK; ODER 36,3 KG BEI INSTALLATIONEN IN NUR EINEN BOLZEN.
ПРЕДУПРЕЖДЕНИЕ Если вам понадобится помощь или что–то непонятно в инструкции, обратитесь в фирму Bell’O® по телефону 1-888-235-7646 (США/Канада) или +1-732-972-1333 (для международных звонков) с 9 утра до 5 вечера (время — восточное стандартное). • НИ ПРИ КАКИХ ОБСТОЯТЕЛЬСТВАХ НЕ ПРЕВЫШАТЬ МАКСИМАЛЬНУЮ НАГРУЗКУ В: 130 ФУНТОВ (59 КГ) ПРИ УСТАНОВКЕ НА ДВУХ СТОЙКАХ ИЛИ ПРИ КРЕПЛЕНИИ К КАМЕННОЙ КЛАДКЕ; ИЛИ 80 ФУНТОВ (36,3 КГ) ПРИ УСТАНОВКЕ НА ОДНОЙ СТОЙКЕ.
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (WP) Wall Plate, 1 Plaque murale, 1 Placa de pared, 1 Supporto a parete, 1 Wandplatte, 1 Настенная плата, 1 (IT) Installation Template, 1 Gabarit de pose, 1 Plantilla de instalación, 1 Schema di installazione, 1 Schablone für Installation, 1 Шаблон для установки, 1 (EC) End Covers, 2 Capuchons, 2 Cubiertas de extremos, 2 Paraspigoli, 2 Endabdeckungen, 2 Концевые крышки, 2 (R) M4/M5,
INCLUDED PARTS PIÈCES INCLUSES PARTES INCLUIDAS PARTI INCLUSE IM LIEFERUMFANG ENTHALTENE TEILE ПОСТАВЛЯЕМЫЙ КОМПЛЕКТ (A) M4 x 12mm, 4 (D) M4/M5, 4 (E) M4/M5, 4 (Q) M6/M8, 4 (P) M6/M8, 4 (B) M4 x 22mm, 4 (C) M4 x 30mm, 4 (G) M5 x 12mm, 4 (H) M5 x 22mm, 4 (I) M5 x 30mm, 4 (U) TOGGLER® brand AF8 ALLIGATOR® Anchor, 4 (J) M6 x 14mm, 4 (M) M8 x 20mm, 4 (K) M6 x 25mm, 4 (N) M8 x 30mm, 4 (L) M6 x 35mm, 6 (O) M8 x 40mm, 4 TOGGLER® brand ALLIGATOR® SOLID-WALL ANCHORS are patented under one or m
NECESSARY TOOLS OUTILLAGE NÉCESSAIRE HERRAMIENTAS NECESARIAS ATTREZZI NECESSARI ERFORDERLICHE WERKZEUGE НЕОБХОДИМЫЕ ИНСТРУМЕНТЫ Phillips-head Screwdriver Tournevis à tête Phillips Destornillador philips (cruz) Cacciavite Phillips Kreuzschlitzschraubenzieher Крестообразная отвертка Masking Tape Ruban de masquage Cinta de enmascarar Nastro adesivo Abdeckband Маскировочная лента Ratchet Set Clé à cliquet à douilles Equipo de trinquete Strumento Del Cricco Schaltklinke Hilfsmittel Набор инструментов с храпов
ATTACHING THE MONITOR ARMS (MA) FIXER LES BRAS DE MONITEUR (MA) CÓMO FIJAR LOS BRAZOS DE LA PANTALLA (MA) FISSAGGIO DEGLI SNODI DELLO SCHERMO (MA) BEFESTIGUNG DER MONITORARME (MA) ПРИКРЕПЛЕНИЕ КРЕПЕЖНЫХ УЗЛОВ МОНИТОРА (МА) SELECT THE CORRECT SCREW Before beginning, test several of the screws in your hardware kit to find the correct size and length for your television.
ATTACHING THE MONITOR ARMS (MA) Attach each Monitor Arm (MA) to the back of your television as shown. Make sure that each Washer (R for M4 or M5 screws, or S for M6 or M8 screws) is placed between the Screw and the Monitor Arm. Don’t place the Washers between the Arms and the television. FIXER LES BRAS DE MONITEUR (MA) Fixer les deux bras de moniteur (MA) au dos du téléviseur comme sur l'illustration.
Use spacers if Monitor Arms (MA) do not fit firmly against the back of the television, such as when the back of the television is curved, contains larger recessed mounting holes, or some other obstruction is in the way. Spacers also provide extra room for cables. The Arms must rest securely on the spacers, and should not be loose.
INSTALLING THE WALL MOUNT IN WOOD POSER LE SUPPORT MURAL SUR DU BOIS CÓMO INSTALAR EL SOPORTE DE PARED EN MADERA INSTALLAZIONE DEL SUPPORTO A PARETE SU LEGNO INSTALLATION DER WANDBEFESTIGUNG IN HOLZ КРЕПЛЕНИЕ НАСТЕННОГО КРОНШТЕЙНА К ДЕРЕВУ FIND THE WOOD STUD(S) Using a stud finder, find the exact location of the studs to which you want to attach the wall mount. Mark the right and left side to determine the center of each stud.
DETERMINE HEIGHT LOCATION OF TELEVISION Measure the distance from the bracket holes to the top and bottom of the TV to determine the center mounting position. Measure from the floor up, and make small marks on the wall to help you determine the desired TV height. Using a level, line up the Installation Template (IT) with your pencil markings and tape it into place.
FOR MASONRY INSTALLATIONS, SEE PAGE 20. POUR UNE POSE SUR DE LA MAÇONNERIE, VOIR PAGE 20. PARA INSTALACIONES EN MAMPOSTERÍA CONSULTE LA PÁGINA 20. PER INSTALLAZIONI A MURO, VEDERE A PAGINA 20. FÜR INSTALLATIONEN IN MAUERWERK, SIEHE SEITE 20. КРЕПЛЕНИЕ К КАМЕННОЙ КЛАДКЕ, СМ. СТР. 20. DRILL PILOT HOLES Follow directions on the Installation Template (IT) carefully. For installations into one stud: drill two holes into the round holes “E”, and “F” in the center of the Template.
A E B C F D Use lines on Installation Template (IT) to align Template with stud pencil markings. Se servir des lignes sur le gabarit de pose (IT) pour aligner le gabarit avec repères de montants au crayon. Utilice líneas en la plantilla de instalación (IT) para alinear la plantilla con las marcas de lápiz en el montante. Utilizzare le linee presenti nello schema di installazione (IT) per allineare lo schema stesso ai segni fatti in matita.
INSTALL THE WALL PLATE (WP) After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
INSTALLING THE WALL PLATE (WP) INTO ONE STUD After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) with Washers (CW) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
MOUNTING TO SOLID CONCRETE, BRICKS, OR CINDER BLOCK POSE SUR DU BÉTON PLEIN, DES BRIQUES OU DES PARPAINGS MONTAJE EN CONCRETO SÓLIDO, LADRILLO O LADRILLOS DE ESCORIAS MONTAGGIO SU CALCESTRUZZO, MATTONI O BLOCCHI IN CEMENTO MONTAGE AN FESTBETON, MAUERZIEGELN ODER SCHLACKENBETONBLOCK КРЕПЛЕНИЕ К НЕАРМИРОВАННОМУ БЕТОНУ, КИРПИЧУ ИЛИ ШЛАКОБЕТОННОМУ БЛОКУ After you have determined your desired TV location, Line up the Installation Template (IT) to ensure you will not drill into any mortar joints.
Level Niveau Nivel Livella Nivellierinstrument Уровень A IT X C B D X DO NOT DRILL INTO MORTAR JOINTS! DRILL HOLES AT LEAST 1" (25.4 MM) FROM THE JOINTS. USE A NEW DRILL BIT TO ENSURE OPTIMUM HOLDING ABILITY. DO NOT USE A HAMMER DRILL! NE PAS PERCER DANS LES JOINTS DE MORTIER ! PERCER LES TROUS À AU MOINS 25 MM (1 PO) DES JOINTS. UTILISER UNE MÈCHE NEUVE POUR ASSURER UNE CAPACITÉ DE MAINTIEN OPTIMALE. NE PAS UTILISER DE PERCEUSE À PERCUSSION ! NO PERFORE LAS JUNTAS DE ARGAMASA.
DRILL PILOT HOLES Follow directions on the Installation Template (IT) carefully. Carefully drill four holes using a 5/16" (or 8mm) masonry drill bit in the “A”, “B”, "C", and "D" locations noted on the Installation Template. Each hole should be at least 3" (76mm) deep. PERCER LES TROUS GUIDES Suivre avec attention les instructions figurant sur le gabarit de pose (IT).
U INSERT ANCHORS Remove Template (IT) and insert TOGGLER® brand ALLIGATOR® Anchors (U). ENFONCER LES CHEVILLES Enlever le gabarit (IT) et enfoncer des chevilles d'ancrage ALLIGATOR® de la marque TOGGLER® (U). COLOQUE LOS ANCLAJES Quite la plantilla (IT) y coloque los anclajes (U) marca TOGGLER® Y ALLIGATOR®. INSERIRE I TASSELLI Togliere lo schema (IT) e inserire i tasselli ALLIGATOR® di marca TOGGLER® (U).
INSTALL THE WALL PLATE (WP) After you have prepared the holes for mounting the Wall Plate (WP), place the Wall Plate over the holes and screw in the Lag Bolts (T) about half way. Use a level to make sure the Wall Plate is level and make any necessary adjustments. Once straight, tighten all of the Lag Bolts completely (do not over tighten!).
INSTALL THE DECORATIVE END COVERS (EC) Line up the two peg inserts on the back of each End Cover (EC) with the two holes at the ends of the Wall Plate (WP), and press into place. Each End Cover is marked with a "L" (for Left side) or "R" (for Right side). POSER LES CAPUCHONS DÉCORATIFS (EC) Aligner les deux chevilles au dos de chaque capuchon (EC) avec les deux trous aux extrémités de la plaque murale (WP) et les enfoncer en place. Les capuchons sont marqués « L » (côté gauche) ou « R » (côté droit).
MOUNTING THE TELEVISION POSE DU TÉLÉVISEUR CÓMO INSTALAR EL TELEVISOR MONTAGGIO DEL TELEVISORE MONTAGE DES FERNSEHERS УСТАНОВКА ТЕЛЕВИЗОРА PREPARE THE MONITOR ARMS (MA) Before you attempt to attach the TV to the Wall Plate (WP), make sure the Monitor Arms (MA) are parallel to the television (in the 0-degree position). This position is indicated by the center marking on the arms as shown.
PREPARE THE SECURITY SCREWS Adjust the Security Screws (L) in the Monitor Arms (MA) so that they do not interfere with installation onto the Wall Plate (WP). Make sure the Security Screws do not extend past the top edge of the bottom mounting bracket of the Monitor Arm as shown. PRÉPARER LES VIS DE SÉCURITÉ Ajuster les vis de sécurité (L) dans les bras de moniteur (MA) afin qu'elles n'entravent la pose sur la plaque murale (WP).
MOUNT THE TELEVISION With the help of an assistant, lift the television and guide the Monitor Arms (MA) onto the Wall Plate (WP) as shown. After the television with the Monitor Arms is attached to the Wall Plate, lock the Arms into place to prevent removal of the television. To lock the Arms, fully turn the Security Screws using a screwdriver so that they extend underneath the Wall Plate. Have an assistant hold the television in place while you do this.
MA MAKE SURE BOTH MONITOR ARMS (MA) ARMS ARE ENGAGED ON BOTH THE TOP AND BOTTOM RAILS OF THE WALL PLATE (WP)! WP S'ASSURER QUE LES DEUX BRAS DE MONITEUR (MA) SONT ENGAGÉS À LA FOIS SUR LES RAILS SUPÉRIEUR ET INFÉRIEUR DE LA PLAQUE MURALE (WP). ASEGÚRESE DE QUE AMBOS BRAZOS DE LA PANTALLA (MA) SE ENGANCHEN EN LOS RIELES SUPERIOR E INFERIOR DE LA PLACA DE PARED (WP).
USING THE TILTING ARM FEATURE Once the television with the Monitor Arms (MA) is securely locked on the Wall Plate (WP), you can safely adjust the tilt feature on the Arms. The Arms can tilt from -5° back to +15° forward, depending on your optimum viewing position. Have an assistant hold the television in place, and turn the lever on the Monitor Arm to loosen. It works like a ratchet so that you can loosen the lever easily in a very confined area.
ИСПОЛЬЗОВАНИЕ УЗЛОВ НАКЛОНА Когда телевизор с крепежными узлами монитора (МА) надежно заблокирован на настенной плате (WP), можно, не опасаясь, использовать функцию наклона. Крепежные узлы можно наклонять от положения -5° назад до положения +15° вперед, в зависимости от наиболее удобного положения для просмотра. Пусть помощник удерживает телевизор на месте, а вы поверните рычаг на крепежном узле монитора, чтобы крепление ослабло.
LIMITED LIFETIME WARRANTY This Bell’O International, Corp. (“Bell’O” or “we”) mounting product SKU # 7745 (“Product”) is warranted for the life of the Product only to the original purchaser and limited to the original installation (“Warranty”). Re-installation of the Product in a different location or with a different monitor or peripheral voids this Warranty. This Warranty is only valid in the United States of America and Canada.
GARANTIE À VIE LIMITÉE Ce produit de fixation Bell’O International, Corp. (« Bell’O » ou « nous ») de n° SKU 7745 (le « Produit ») est garanti pendant la durée de vie du Produit uniquement à l'acheteur initial et dans les limites de la pose initiale (« Garantie »). La réinstallation du Produit à un emplacement différent ou avec un téléviseur ou périphérique différent annule cette Garantie. Cette garantie est valable uniquement aux États-Unis d’Amérique et au Canada.
GARANTÍA LIMITADA DE POR VIDA Este producto de montaje SKU # 7745 (“Producto”) Bell’O International, Corp. (“Bell’O” o “nosotros”) está cubierto por la garantía durante la vida del Producto solo para el comprador original y está limitada a la instalación original (“Garantía”). La Garantía solo es válida en los Estados Unidos de Norteamérica y Canadá.
GARANZIA LIMITATA A VITA Questo prodotto di supporto SKU # 7745 (“Prodotto”) di Bell’O International, Corp. (“Bell’O” o “noi”) è coperto da garanzia per la durata della vita del Prodotto unicamente per l'acquirente originale e solo per l'installazione originale (“Garanzia”). La reinstallazione del Prodotto in posizione diversa, o con schermo o periferica diversi, rende questa Garanzia nulla. Questa Garanzia vale unicamente negli Stati Uniti d'America e in Canada.
BESCHRÄNKTE GARANTIE AUF LEBENSZEIT Eine Gewährleistung für dieses Montageprodukt SKU Nr. 7745 (das "Produkt") von Bell’O International Corporation (“Bell’O” oder “wir”) wird für die Lebenszeit des Produkts nur dem ursprünglichen Käufer gegenüber zugesichert und beschränkt sich auf die ursprüngliche Installation ("Gewährleistung"). Eine erneute Installation des Produkts an einer anderen Stelle oder mit einem anderen Monitor oder an einer anderen Außenfläche macht diese Garantie ungültig.
ОГРАНИЧЕННАЯ ПОЖИЗНЕННАЯ ГАРАНТИЯ Фирма Bell’O International, Corp. (“Bell’O” или “мы”) дает гарантию на кронштейн SKU # 7745 (“Продукт”) на время жизни Продукта только первоначальному покупателю и только на первую установку (“Гарантия”). Повторная установка Продукта в другом месте, либо с другим монитором или с другой периферийной аппаратурой аннулирует эту Гарантию. Эта Гарантия имеет силу только в Соединенных Штатах Америки и Канаде.
NOTES • NOTE • NOTAS • NOTES • NOTIZEN • ПРИМЕЧАНИЯ
NOTES • NOTE • NOTAS • NOTES • NOTIZEN • ПРИМЕЧАНИЯ
BELL'O INTERNATIONAL CORPORATION 711 Ginesi Drive, Morganville, NJ 07751 (888) 235-7646 • (732) 972-1333 www.bello.
