Installation Guide

ManualsBrandsBellaterra Home ManualsBath8 in. Widespread Double Handle Bathroom Faucet with Pop-Up Drain with Overflow in Brushed Nickel

Thank you for selcting our product for your home.

We hope that you are completely satised with your purchase.Please read below instructions carefully before installing new faucet.

Two handle lavatory faucet with push-up pop-up drain

S8288

S8225

S8518

S8223

S8227

BELLATERRA HOME, LLC

Tools you will need:

Adjustable Wrench

Screwdriver

Teon Tape Silicone Sealant

Bucket

Safety Goggles

Silicone Sealant

Prior to Installation:

• Turn o the hot and cold water supply at the angle stops

and turn on the old faucet to release any built up pressure.

Remove existing faucet. Clean sink or countertop to remove

any debris, plumber’s putty, or silicone.

• Place bucket under angle stops. Turn on to ush any debris

prior to installing new plumbing. Shut o angle stops.

• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)

• Max countertop thickness: 1-3/8

”

Care & Maintenance:

* To keep the product clean & shining, follow the steps below:

• 1. Rinse with clean water & dry with a soft cloth.

• 2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.

• 3. Do not use cloth with a coarse surface.

• 4. Unscrew the aerator and clean when necessary.

* This installation manual is subject to change without further notice.

* Please read your care and maintenance documentation to determine the limits of proper use.

* This product has been manufactured and tested to the highest quality standards .We oer our customers thoughtfully

crafted xtures & accessories, engineered for enduring performance over years of use.

1/16”(1 mm) min.

1-3/8”(35 mm) max.

1-3/8” (35 mm) min.

/1-1/2” (38 mm) max.

Model Number:

S8288-8-BN-W

S8288-8-MB-W

S8225-8-BN-W

S8225-8-MB-W

S8518-8-BN-W

S8518-8-MB-W

S8223-8-BN-W

S8223-8-MB-W

S8227-8-BN-W

S8227-8-MB-W

S8288-8-PC-W

S8288-8-GD-W

S8288-8-ORB-W

S8225-8-PC-W

S8225-8-GD-W

S8225-8-ORB-W

S8518-8-PC-W

S8518-8-GD-W

S8518-8-ORB-W

S8223-8-PC-W

S8223-8-ORB-W

S8227-8-PC-W

S8227-8-GD-W

S8227-8-ORB-W

Summary of content (4 pages)

PAGE 1
B BELLATERRA HOME, LLC Thank you for selcting our product for your home. We hope that you are completely satisfied with your purchase.Please read below instructions carefully before installing new faucet.
PAGE 2
Faucet Installation 1 2 15 14 13 1.Shut off water supplies. Remove old faucet.Clean sink surface in preparation for new faucet. 2.Place the spoutthrough center hole (The hole diameter should be 1-3/8”) of the sink. Under sink,secure firmly to sink with rubber washer(15),metal washer(14)and nut(13). 3 4 Hot Cold Hot 9 8 10 3 2 1 A B C K 3.Insert the Valve body assembly(8) with the hot supply label on the left (hot) side. Hold the body in the proper position.
PAGE 3
Pop-up Drain Installation 6A 6B Drain plug Pop-up Top gasket Drain body Drain body Top gasket Rubber washer Mounting nut 6A.NOTE: Check that you have the appropriate drain for your sink. * If you are installing this pop-up in a sink that has an electronic faucet,please use plastic tailpiece. 6B.Insert body into sink. If you wish to use silicone as a seal, remove the top gasket and apply silicone to underside of drain body.Otherwise, leave gasket in place.
PAGE 4
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly,take the following corrective steps: PROBLEM CAUSE ACTION Aerator drips or has inconsistent water flow pattern Aerator may be dirty or not seated properly Unscrew aerator with aerator key and clean out debris Drain is leaking Washers may be compromised or installed incorrectly Check washers to make sure they are installed correctly and not cracked Exploded Drawing RP(Replacement Parts) NO.