GB Operators Manual 4 US Operators Manual 12 F Manuel De L'Opérateur 20 E Manual del Operador 28 RUS Рyкoвoдcтвo для oпepaтopa 36 TILE SAWS - Spare Parts Book - Pièces détachées - Libro Despiece - Запасные части Книга 44 1 870/30006/3 06/14
EC DECLARATION OF CONFORMITY / DECLARATION CE DE CONFORMITE / DECLARACIÓN DE CONFORMIDAD CE / DECLARAÇÃO CE DE CONFORMIDADE / EG-VERKLARING VAN OVEREENSTEMMING / EF OVERENSSTEMMELSESERKLÆRING GB F E P NL DK We, Belle Group Sheen UK, Sheen, Nr.
ɋȿɊɌɂɎɂɄȺɌ ɋɈɈɌȼȿɌɋɌȼɂə / EÜ VASTAVUSDEKLARATSIOON / ATBILSTĪBAS DEKLARĀCIJA / ES ATITIKTIES DEKLARACIJA / £©² ¤¢ ¤ ² ǻǻ ǺǽȀȌȇǽ ǿǸȈǸȀȀǽȀȄȈǽȈǸȇ RUS EST LV LT BG GR Ɇɵ, ɧɢɠɟɩɨɞɩɢɫɚɜɲɢɟɫɹ, ɨɬ ɢɦɟɧɢ Belle Group Sheen (ȼɟɥɢɤɨɛɪɢɬɚɧɢɹ), Sheen, Nr.
How To Use This Manual GB This manual has been written to help you operate and service the Tile Saw safely. This manual is intended for dealers and operators of the Tile Saw. Foreword The ‘Environment’ section gives instructions on how to handle the recycling of discarded apparatus in an environmentally friendly way. The ‘General Safety’ and ‘Health and Safety’ sections explain how to use the machine to ensure your safety and the safety of the general public.
GB Technical Data Model Minitile 180 Minitile 200 Minitile 230 Magiktile 180 Maxitile 260 Width (mm) 478 460 585 394 440 Height (mm) 270 260 333 158 1240 1150 Length (mm) 498 330 560 394 Blade Diameter (mm) 180 200 230 180 200 Blade Speed (rpm) 2800 2800 2800 2800 2800 Blade Centre Hole (mm) 25.4 25.4 25.4 25.4 25.4 Max.
General Safety GB WARNING When using electric tools, following safety precautions should always be followed to reduce the risk of ¿re, electric shock and personal injuries. Read and follow all these instructions before attempting to operate this product. Keep your work area perfectly clean - Cluttered areas invite injuries. Consider work area environment - Don’t expose tools to rain. - Don’t use tools in damp or wet locations. Keep work area well lit.
Health and Safety GB PPE (Personal Protective Equipment). Suitable PPE must be worn when using this equipment i.e. Safety Goggles, Gloves, Ear Defenders, Dust Mask and Steel Toe capped footwear. Wear clothing suitable for the work you are doing. Tie back long hair and remove any jewellery which may catch in the equipment’s moving parts. Dust. The sawing process will occasionally produce dust, which may be hazardous to your health. Always wear a mask that is suited to the type of dust being produced.
Adjusting The Blade Guard GB CAUTION The machine is equipped with a continuous diamond rim blade. Even though this blade has been designed for operator safety if unintentionally touched, pay particular attention to avoid contact between your ¿ngers and the blade during operation of the machine. MINITILE & MAGIKTILE ONLY!! Position the blade guard approximately half a centimetre above the tile surface. Lock the blade guard in position by fully tightening the screw illustrated in the ¿gure.
Operating Instructions GB MINITILE & MAGIKTILE ONLY!! Cutting at 90° Position the cutting guide and lock it by tightening the knobs fully. (See Figure 5a) The picture on the right shows how to position hands correctlyduring cutting at 90. The forward movement of the piece must be proportional to the blade cutting capacity, to prevent hazardous fragments that would involve accidents or injuries from breaking off.
Maintenance GB CAUTION Before performing any maintenance operation, ensure the machine is disconnected from the power supply. MINITILE & MAGIKTILE ONLY!! DIAMOND BLADE DISASSEMBLY Remove the blade guard. Use the 4mm Allen Key to hold the motor shaft. Unscrew the blade Àange block nut with the 19mm spanner. After removing the blade, clean the blade Àange thoroughly and check for wear. Lubricate surfaces with ¿ne oil, then ¿t new blade.
Troubleshooting Guide GB HAVE YOUR MACHINE REPAIRED BY A QUALIFIED PERSON ONLY This electric machine complies with the relevant safety rules. Repairs should only be carried out by quali¿ed persons using original spare parts, otherwise this may result in considerable danger to the user. Fault The machine does not Cause The power supply cable is damaged or Remedy Press the plug ¿rmly into the power socket. function. not properly connected. No voltage in the socket. Have the socket checked.
