Users Guide & Installation Handbook Belling 60 - 70 - 90cm Hob Touch AU Part No 082757402 Date 29.05.
CONTENTS & OUR WARRANTY CONTENTS Important Notice • SAFETY • USING THE PRODUCT • CLEANING • INSTALLATION INSTRUCTIONS • TECHNICAL DATA • CUSTOMER CARE Please note there may be a cooling fan fitted to this appliance. It is an integral part of its safety and functionality. When the appliance is installed care must be taken that the cooling fans performance is not impeded by any objects coming into contact with it.
SAFETY BEFORE USING THE PRODUCT Electric Hob Make sure that you have removed all packaging and wrapping. Some of the items inside this appliance may have additional wrapping. Do • Always ensure that pan bases are dry and flat before using them on the hob. WARNING! This appliance is • Always position pans over the centre of the heat zone, and turn the handles to a safe position so they cannot be knocked or grabbed.
SAFETY • • • • • • • • Never leave any cook zone on without a pan covering it. This causes a fire hazard. Never use the hob surface as a chopping board or food preparation area, as this may lead to it becoming damaged. Never put metal cooking utensils, cutlery, knives or other metal objects on the hob. They could become hot if they are near a cooking area which is in use. Never use the hob if the surface is cracked, broken or shattered. This creates a high risk of injury.
USING THE HOB - ELECTRIC (CERAMIC) WARNINGS • Do not use the ceramic hob if the glass surface is cracked, as electrical parts are directly beneath. Switch off the appliance at the supply to prevent electric shock and contact your supplier. • The hob surface remains hot after use. DO NOT TOUCH. • The appliance is not intended to be operated by means of an external timer or separate control system.
CLEANING ELECTRIC HOB Ceramic glass hobs • The ceramic hob top can be cleaned using a clean, damp cloth or kitchen paper. Do not use a used dishcloth or sponge as they can leave a film of detergent on the surface which can lead to discoloration. Please ensure that the elements are cooled fully to avoid steam burns. • You can use a specialist ceramic cleaner to restore the surface, but use sparingly to avoid coating the hob top too thickly. Too much cream cleaner will lead to discolouration.
MINUTE MINDER (IF FITTED) To check remaining time: Minute Minder • Refered heater’s leds Refered heater’s leds TIMER A minute-minder can be associated to any of the selected cooking zones, upto 99 mins. When the set time expires the buzzer sounds and the heater switches off. To turn the heater back on, touch and hold the heater symbol. Touch the timer symbol. To adjust the set time: • • Touch the timer symbol. Using the “+” or “-” symbols, set the time required in minutes.
TROUBLE SHOOTING If you encounter a problem, it is often something minor, please read some of the suggested tips below. The hob is not working Check the fuse/circuit breakers to see if you are experiencing power failure. The hob has turned it’s self off Check that the main on/off switch has not been touched accidentally, remove any objects on the hob and try turning it back on again. Repairs Repairs are to be carried out by trained customer service technicians.
ERROR CODES Heater display Fault Action F0 Touch control software error. If error has occurred after initial calibration (see initial power on) disconnect and reconnect the power from the hob again, re-calibrate the hob again, if the error persists or appears again in normal use, call customer services. Fc or F Touch control is too hot and has turned off the heaters. Wait until the temperature goes down. Hob will automatically start again once it reaches normal temperature.
INSTALLATION GENERAL INFORMATION Installation should only be carried out by a qualified installer or engineer. Please keep to the following points most carefully; Although every care has been taken to ensure this appliance has no burrs, or sharp edges, We recommend that you wear protective gloves when installing and moving this appliance. This will prevent injury. The hob should not be fitted above a washing machine, a fridge or a freezer.
INSTALLATION Secure the hob to the worktop by means of the brackets provided, taking the thickness of the worktop into account. Depending on your appliance it will be supplied and installed using one of the following installation methods. Method 1 (fig 1A) uses spire clips which must be fitted to the base of the hob prior to fitting the brackets. If the appliance is installed with an oven underneath then the dividing partition is not required.
TECHNICAL DATA SUPPLY: 220 -240V ~ 50Hz 5.
HOB WIRING 51 15 51 15 S 2 Y Bk W Or Bk R Bk Bk Bn 4 5 Bn Bn Bk Bk H Y Or Y Bk R Bk W H 2 Wiring colour code: Bk-Black, Bn-Brown, Bu-Blue, Gn-Green, Or-Orange, R-Red, W-White, Y-Yellow, Gy-Grey, V-Violet 0W 21 0 H S 0W 21 Bk 54 18 57 W 00 8 1 W H 0 12 2 00 S 12 BELLING CH60TX - AU S 2 ISSUE 1 13/07/2011
2200W 18 51 S 0W HOB WIRING 2 54 15 Bk Y Bn Bk Bu W Or S 2 H Bn R Bk Bk Bn 4 5 Bn Bn Bk Bk Or Y Bn Bu Bk W Bk R Bk S 0 12 2 H Wiring colour code: Bk-Black, Bn-Brown, Bu-Blue, Gn-Green, Or-Orange, R-Red, W-White, Y-Yellow, Gy-Grey, V-Violet BELLING CH70TX AU H S 2 H W 00 18 51 1200W 15 54 18 13/07/2011 ISSUE 1
Please keep this handbook for future reference, or for anyone else who may use the appliance.
CONTACT US Calling for a service If you should experience any problems with your cooker please contact your retailer or place of purchase. Important note: Service work is to be conducted by authorised persons only. It is also adviseable that your cooker is checked regularly and maintained in good condition. An annual maintenance is recommended. Always check the instruction book before calling a service agent to make sure you have not missed anything.
