Users Guide & Installation Handbook Belling SCGHU60GC / SCGHU70GC Built-in Gas Hobs UK 1.
CONTENTS & INTRODUCTION CONTENTS • SAFETY • USING THE PRODUCT • CLEANING • INSTALLATION INSTRUCTIONS • TECHNICAL DATA • CUSTOMER CARE INTRODUCTION Thank you for buying this Britishbuilt appliance from us. This guide book is designed to help you through each step of owning your new cooker, from installation to use. Please read it carefully before you start using your product, as we have endeavored to answer as many questions as possible, and provide you with as much support as we can.
SAFETY WARNING! This appliance and its accessible parts may become hot during use. To avoid burns, children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
SAFETY General Servicing should be carried out only by authorised personnel. Do not spray aerosols in the vicinity of this appliance while it is in operation. Do not store or use flammable liquids or items in the vicinity of this appliance. Do not modify this appliance. • Always ensure that pan bases are dry, stable and flat before using them on the hob. • Always use pans which are no smaller than 100mm (4”), or larger than 250mm (10”).
SAFETY Avoiding damage to the appliance. DISPOSAL Objects that melt and things that boil over can burn onto the hob and should be removed as soon as possible. Packaging Material To avoid damage to cookware do not allow sauce pans or frying pans to boil dry. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. Do not use the cooking zones with empty cookware or without cookware in place.
USING THE HOB - GAS • If your hob is supplied with left and right handed pan supports, ensure that they are located over the alignment pins and are sitting flat on the hob. • Use pans which are large enough to avoid overflows onto the hob surface. • Wipe any spillage as soon as possible. • Clean the hob top as regularly as possible, this will prevent any build up of grease which may be a fire hazard.
USING THE HOB - GAS FOLD DOWN LID (IF FITTED) Caution: Glass lids may shatter when heated. Turn off all the burners before shutting the lid. When opening and closing the lid, use the cooler outer sides of the lid glass. The lid must be opened fully, so there is no danger of it closing while the hob is being used. Appliances fitted with glass lids are fitted with a safety system which will automatically turn off the hot plate burners if they are inadvertently left on as the lid is closed.
CLEANING General • It is important to clean the product regularly as a build up of fat can affect its performance or damage it and may invalidate your guarantee. • Always switch off your appliance and allow it to cool down before you clean any part of it. • Do not use undiluted bleaches, products containing chlorides, wire wool or abrasive cleaners on aluminium, stainless steel, or plastic/ painted parts as they can damage the appliance. Nylon pads can also be unsuitable.
CLEANING GAS HOB Cast iron griddle or pan supports (if fitted) Burner caps and heads • The slots in the burner head where the flames burn should be cleared of deposits. • Clean with a nylon brush, rinse and then dry thoroughly. There may be brown coloured markings on your burners; these are carbon deposits or fat stains and can be removed using a soap filled pad. • Do not put burners in the dishwasher or soak them.
INSTALLATION Installation This appliance must be installed in accordance with the regulations in force, and only in a well ventilated space. Read the instructions before using or installing this appliance. This appliance is factory set for use with natural gas only. Regulations & Standards Prior to installation, ensure that the local distribution condition (nature of the gas and gas pressure) and adjustment of the appliance are compatible.
INSTALLATION Ventilation Requirements The room containing the appliance should have an air supply in accordance with BS5440: Part 2 • All rooms require an openable window, or equivalent, and some rooms will require a permanent vent as well. • For room volumes up to 5m3 an air vent of 100cm2 is required. • If the room has a door that opens directly to the outside, or the room exceeds 10m3 NO AIR VENT is required. • For room volumes between 5m3 and 10m3 an air vent of 50cm2 is required.
INSTALLATION Clearances & dimensions The room should have good light and ventilation but be free from draughts. The worktop should be at least 600mm deep, & 30mm thick to enable the cutout to be made to the dimensions shown below. A minimum distance of 40mm should be maintained between the hob and rear wall / combustible surface. A minimum distance of 40mm should be maintained between the hob and any side walls / combustible surface.
INSTALLATION Important Information It is important when installing front control gas hobs, that the work top cut out is the same as is quoted in this installation manual. If the cut out is too large, then batons must be fitted to the front, rear and sides - to correct the discrepancy and ensure the correct fit. Please ensure that if batons are fitted they are level with the top surface of the work top Please ensure that the seal for the hob has full contact with the work top surface.
INSTALLATION Fit the hob into the cutout & secure to worktop Place the hob into the cutout and secure in place using the four brackets and screws provided. The brackets should be orientated to suit the worktop thickness as shown, then inserted into the four slots (two on the front edge and two on the rear) and screwed into the underside of the worktop using the woodscrews provided.
INSTALLATION Alternative clamp positions If the front and rear clamp positions are problematic, alternative positions can be used on the sides of the hob, dependant on the particular installation. These positions will require clearance from any cabinet sides and may effect how tightly the hob will meet the worktop. Stone (Granite or equivalent) worktops Depending on the type of worktop being used, there may or may not be any backing material to screw the clamp screws into. 1.
INSTALLATION Connect gas hob to gas supply The inlet is at the rear RHS of the hob. The hob may be connected to the gas supply either by rigid pipework or flexible connection. Flexible connections Use a 900mm - 1125mm length of flexible connector. Ensure that the hose is installed hanging freely downwards, is not trapped, is not subjected to undue forces and is not supported at the bottom by a horizontal surface. Natural Gas - Flexible connections should comply with BS669, latest edition.
INSTALLATION Connect to the electricity supply For hobs that are supplied/manufactured with a 13Amp supply cord and plug only. Warning: Ensure that the power rating of the appliance is compatible with a 13Amp supply beore connecting to the electricity supply. i.e. 2.8kW. Warning: This appliance must be earthed. The flexible mains lead is supplied connected to a BS 1363 fused plug, the plug is fitted with the correct fuse. Replace only with a fuse of the same rating and type.
INSTALLATION Troubleshooting Before you call Customer Care, please check the following points: Burner fails to ignite: • Check the electricity supply is on. • Check the fuse. There is a spark to the burner but it fails to ignite: • Check that the flame holes in the flame spreader are clear of water or deposits. • Check that the gas supply is turned on. Smell of gas: • Check that none of the controls have inadvertently been turned on.
TECHNICAL DATA This information is for the following appliances: Belling Hobs SCGHU60GC / SCGHU70GC - NG only Data badge Appliance Class Class 3 Bulit-In Hotplate Gas pressure settings G20 Natural Gas @ 20 mbar Underside of the hob base Electrical supply Countries of destination 220 - 240V ~ 50Hz 1W GB - Great Britain, IE - Ireland Ignition Mains repetitive ignition.
CUSTOMER CARE CUSTOMER CARE WEB SHOP Having purchased a superior cooker, hob or hood from us, you’ll naturally want to keep it looking great. And who better to help you care for it than the manufacturer? We offer an extensive range of accessories, components and cleaning products which, will instantly give your cooker a good as new look. range of Bake ware and Cookware essentials including Roasting Pans, Cake Tins and Non-Stick Cooking Liners. For all enquires, please visit our Web Shop at www.gdhaonline.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
CUSTOMER CARE To contact Belling about your appliance, please call Warranty Registration 0844 481 0182 to register your appliance Customer Care Helpline 0844 815 3746 in case of difficulty within the UK Alternatively general, spares and service information is available from our website at www.belling.co.uk Please ensure that you have the product’s model no and serial no available when you call.