User manual

ManualsBrandsBellini ManualsCooktopBDG302WGA

啊哈

Installation and User manual

Content

Safety instructions---------------------------------- 2

Product description--------------------------------- 4

Installation---------------------------------------------6

Start using your appliance--------------------------10

Maintenance and troubleshooting----------------12

Warranty------------------------------------------------ 14

201211211 issue 1

Black Glass Top-surface

Built-in Gas Cooktop

BDG604G, BDG604G-F, BDG604GA, BDG604GA-F

BDG302WG, BDG302WG-F, BDG302WGA, BDG302WGA-F

BDG302RG, BDG302RG-F, BDG302RGA, BDG302RGA-F

BDG301G, BDG301G-F, BDG301GA, BDG301GA-F

For warranty service call 1300 373 199(Australia)

or 0508 123108(New Zealand) to connect you to

the nearest authorised service centre

Summary of content (15 pages)

PAGE 1
201211211 issue 1 啊哈 Black Glass Top-surface Built-in Gas Cooktop Installation and User manual Content Safety instructions---------------------------------- 2 Product description--------------------------------- 4 Installation---------------------------------------------6 Start using your appliance--------------------------10 Maintenance and troubleshooting----------------12 Warranty------------------------------------------------ 14 For warranty service call 1300 373 199(Australia) or 0508 123108(New Ze
PAGE 2
Safety instructions This manual explains the proper installation and use of your appliance, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference. In case of failure, only the Authorized Technical Service may repair this hob. Otherwise the guarantee will be null and void. Warning General safety z z z highly inflammable materials or fusible by licensed gasfitters / authorized persons. objects (e.g.
PAGE 3
diameter and no more than 1.0metre in length. Safety instructions Any hose assembly used must be restrained Safety when installation from accidental contact with the flue outlet of an z under bench oven. z Do not use or store flammable materials in the appliance storage drawer or near this appliance. How to avoid damage to the appliance Do not spray aerosols in the vicinity of this z appliance while it is in operation. z For Universal LPG appliance:- Where this falling onto it.
PAGE 4
Burner Product description BDG604GA, BDG604GA-F *BDG604G, *BDG604G-F * have no aluminum trim Trivet Aluminum trim Control knobs BDG302W/RGA, BDG302W/RGA-F *BDG302W/RG, *BDG302W/RG-F, BDG301GA,BDG301GA-F *BDG301G,*BDG301G-F, * have no aluminum trim * have no aluminum trim Burner Trivet Aluminum trim Control knobs 4
PAGE 5
Accessory Name Picture Quantity ( for reference only, physical unit maybe different) User Manual 1 Installation clip 1 ?? 4 for BDG604G(-F), 3 for Screws ST4.2x24 BDG302*G(-F)&BDG301G(-F) Adhesive sealing tape 1 Natural gas regulator 1 Test point adapter 1 Technical Specifications product Cut-out dimensions Size (h x w x d) mm ( w x d)mm BDG604G/A(-F) 105x584x510 552 x 470 12.7Kgs 220-240V/50Hz 0.5W BDG302*G/A(-F) 100x300x510 266 x 478 7 Kgs 220-240V/50Hz 0.
PAGE 6
Installation Before installation: z Before cutting into any bench tops, ensure the minimum clearances to walls, adjacent surfaces and overhead surfaces required by the relevant gas appliance installation code (see above) will comply. Dimensions are specified in millimeters (mm) Overhead cupboards and range hood = 650 mm. Side and rear clearance = 200 mm to any burner edge. Overhead exhaust/ceiling fan = 750 mm Horizontal surfaces adjacent the hob = less than or equal to the hob height.
PAGE 7
2. Place burner box Apply the adhesive sealing tape to the underside lip of the burner box. Shown at G opposite. Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench. 3. Fit burners and trivet. Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T). The ignitor (S) must be clean for trouble free sparking.
PAGE 8
temperature does not exceed 75oC at any point along its length. After having installed the hotplate, the GPO must always be in an accessible position. Wiring diagram for BDG302*G/A(-F) Wiring diagram for BDG604G/A(-F) Wiring diagram for BDG301G/A(-F) 4. Gas connection Install in accordance with relevant gas standards and/or codes of practice applicable.
PAGE 9
Fit the duplicate data plate (supplied in separate bag) on a surface adjacent to the hotplate, for example, the inside of the cupboard door so it is clearly visible for any service technician. SETTING THE GAS PRESSURE: Fit a manometer with a 6 mm rubber hose to the test point on the regulator (for natural gas). For the Model BG604G/A(-F), light Triple Ring and Auxiliary burner on and adjust test point pressure to 1.00 kPa.
PAGE 10
Start using your appliance Description Explanation These show which zone is under control. Zone indicators Flame power Flame power of the zones, is the lowest and is the highest. The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to mains power supply (i.e. nominal 230 V ac) to operate. If power is not available, the hotplate will still work but the burners will have to be lit with a match or similar.
PAGE 11
BURNER AND UTENSIL CHOICE Depending on the hotplate model, the burner choices are: BDG604G/A(-F): Auxiliary (small), Semi-Rapid x2 (medium), and Wok (triple ring) burners. BDG302WG/A(-F): Semi-Rapid (medium), Wok (triple ring) BDG302RG/A(-F): Semi-Rapid (medium), Rapid (large) BDG301G/A(-F): Wok (triple ring) The maximum utensil (pan) diameters in millimetres ٛ (mm) for each burner are: The minimum utensil (pan) diameters in millimetres 1.
PAGE 12
Maintenance & Troubleshooting Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the Use a cotton bud, tooth brush, or some other item to enameled parts. Avoid leaving alkaline or acid clean out any incrustations or dirt from the four holes substances(lemon juice, vinegar etc.) on the surfaces. marked(H) STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. weekly) to ensure long life expectancy of the hotplate.
PAGE 13
TROUBLESHOOTING Servicing of the hotplates must only be done by an authorised service representative (see back of this booklet) and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted. It is recommended the hotplate serviced by an authorized person at least every 2 years. This service is not covered by warranty. Abnormal conditions include: z Excessively yellow or sooting flame type. z Flame lifting off the burner ports.
PAGE 14
WARRANTY 1.1 In this warranty: 1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and Consumer Act 2010; 1.1.2 Company means GSM Sales Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose Park SA 5067. Telephone 08 8122 2390. Email admin@gsmsales.com.au; 1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer Law as the original purchaser of a Bellini product; 1.1.
PAGE 15
1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain the benefit of this warranty. 1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and from your home. 1.