工程部 2014.07.16 正式发行 工程部 2014.07.
工程部 2014.07.16 正式发行 工程部 2014.07.
PRODUCT SPECIFICATION PRODUCT DESCRIPTION: MICRO-HI POWER CONNECTOR PRODUCT NUMBER: PCB SIDE: 70094 SERIES 70095 SERIES 70096 SERIES HOUSING FOR CABLE SIDE: 70093 SERIES 70189 SERIES TERMINAL FOR CABLE SIDE: 70097 SERIES REVISION: B.1 ECR/ECN NUMBER: DOCUMENT NUMBER 2017 / 02/ 07 1 of 11 PS-70094-001 EK2017-0028 DATE: SHEET No. CREATED / REVISED BY: CHECKED BY: APPROVED BY: Kevin Miao Ivanov Wang Ivanov Wang Form No.: QR-QP025-15 REV.
PRODUCT SPECIFICATION 1.0 SCOPE..................................................................................................….................3 2.0 APPLICABLE DOCUMENTS……………………………............…..…........................3 3.0 CONSTRUCTION AND MATERIAL..........................................................................3 4.0 RATINGS……………………………………….........….…….........................................3 5.0 PERFORMANCE, TEST REQUIREMENT AND PROCEDURES SUMMARY.……..5 6.0 TESTING SEQUENCE……… ..
PRODUCT SPECIFICATION 1.0 SCOPE This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) square pin headers when mated with either printed circuit board (PCB) connector. 2.0 APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence.
PRODUCT SPECIFICATION 4.3 CURRENT DERATING AND APPLICABLE WIRES Current is dependent on connector size, contact material, plating, ambient temperature, printed circuit board characteristics and related factors. Actual current rating is application dependent and should be evaluated for each application. AWG Outside Insulation Diameter 16 2.40 mm 18 2.10 mm 20 1.85 mm 22 1.85 mm 24 1.85 mm 26 1.27 mm 28 1.27 mm 30 1.
PRODUCT SPECIFICATION 5.0 PERFORMANCE, TEST REQUIREMENT AND PROCEDURES SUMMARY 5.1 APPEARANCE REQUIREMENTS Item Test Description 1 Examination of product Reference Standard Test Method Visual according to applicable quality inspection plan. Meet the requirements of product 5.2 ELECTRICAL REQUIREMENTS Reference Standard Item Test Description 2 Contact Resistance (Low Level) Mate connectors: apply a maximum voltage of 20 mV and a current of 100 mA.
PRODUCT SPECIFICATION Terminal Insertion Force (into Housing) Apply an axial insertion force on the terminal at a rate of 25 ± 6 mm per minute. 14.7 N (3.3 lbf) MAXIMUM insertion force 9 Durability Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to Environmental Tests. 6 milliohms MAXIMUM 10 Vibration (Random) Mate connectors and vibrate per EIA 36428,test condition VII, Letter D. Test Duration: 15 minutes each axis.
PRODUCT SPECIFICATION 5.4 ENVIRONMENTAL REQUIREMENTS Item Test Description Test Method Reference Standard 15 Thermal Aging Mate connectors; expose to: 240 hours at 105 ± 2°C or 500 hours at 85 ± 2°C 6 milliohms MAXIMUM Mate connectors: expose to a temperature of 40 ± 2°C with a relative humidity of 9095% for 96 hours. Note: Remove surface moisture and air dry for 1 hour prior to measurements.
PRODUCT SPECIFICATION 6.0 TESTING SEQUENCE 6.
PRODUCT SPECIFICATION 6.2 IR PROFILE Recommended Reflow Pre-Solder Process and Profile. Actual reflow profile also depends on equipment, solder paste, PCB thickness, and other components on the board. Please consult your solder paste & reflow equipment manufacturer for their recommendations to adopt a suitable process. 260°C Max 10 second/cycles 2 cycles(Peak Temperature) Notes : 1. Reflow solder preheat at 3°C/s to 150°C. 2. Reflow at 255°C for 30s per figure. 3. Peak temperature to be at 260 +0/-5°C.
PRODUCT SPECIFICATION 7.0 OTHER INFORMATION 7.1 STANDARD POLARIZATION FOR HEADERS REVISION: B.1 ECR/ECN NUMBER: DOCUMENT NUMBER 2017 / 02/ 07 10 of 11 PS-70094-001 EK2017-0028 DATE: SHEET No. CREATED / REVISED BY: CHECKED BY: APPROVED BY: Kevin Miao Ivanov Wang Ivanov Wang Form No.: QR-QP025-15 REV.
PRODUCT SPECIFICATION 7.2 STANDARD POLARIZATION FOR RECEPTACLES REVISION: B.1 ECR/ECN NUMBER: DOCUMENT NUMBER 2017 / 02/ 07 11 of 11 PS-70094-001 EK2017-0028 DATE: SHEET No. CREATED / REVISED BY: CHECKED BY: APPROVED BY: Kevin Miao Ivanov Wang Ivanov Wang Form No.: QR-QP025-15 REV.