Owner’s Manual Beltronics 5442 West Chester Road West Chester OH 45069 USA USA 800.341.2288 www.beltronics.com ©2012 Beltronics Designed in USA • Manufactured In Canada Features, specifications and prices subject to change without notice.
Congratulations The Bel Pro200 is the most advanced radar, laser and safety detector ever designed by Beltronics. The Bel Pro200 includes full X, K, SuperWide Ka, and Safety Warning System radar capability, front and rear laser detection, varactor-tuned (VTO) microwave receiver, digital signal processing (DSP) for superior range and reduced false alarms, our patented Mute and AutoMute, audible and visual band alerts, and all the performance you’d expect from Beltronics.
Quick Reference Press the RVW button to go from one category to the next Table of Contents Press the CHG button to change your setting within a category PILOT (Power-on indication) Pilot HWY Pilot H * Full word:AutoScan or City or Highway Letter:A or C or H VOICE Voice ON Voice OFF * Voice alerts on Voice alerts off POWER-ON SEQUENCE PwrOn STD PwrOn FST * Standard power-on sequence Fast power-on sequence AUTOMUTE aMute ON aMute OFF * AutoMute on AutoMute off CITY MODE SENSITIVITY City STD C
Quick Reference Guide To begin using your Pro200, just follow these simple steps 1 QuickMount Slot Insert the Pro200’s adjustable Windshield mount into this slot. Page 7 Plug the small end of the power cord into the side jack of the detector, and plug the large end of the power cord into your car’s lighter socket. QuickMount Button Press the button, and slide the Windshield mount into one of its four locking positions. Page 7 2 Mount your Pro200 on the windshield using the supplied windshield mount.
Installation Power Connection Mounting Location To power your Pro200, plug the small end of the power cord, (telephone-type connector) into the modular jack on the Pro200’s right side, and plug the lighter plug adapter into your vehicle’s lighter socket or accessory socket. WARNING: Beltronics cannot anticipate the many ways the Pro200 can be mounted. It is important that you mount your Pro200 where it will not impair your view nor present a hazard in case of an accident.
Controls and Features Power Voice Alerts To turn your Pro200 on or off, press the PWR button located on the top.When you turn your Pro200 on, it goes through a sequence of alerts. If you prefer, you may program your Pro200 for a shorter power-on sequence. See the Programming section for details. The Pro200 provides digital voice announcements of radar and laser bands detected. If Safety Radar (SWS) is turned on, a safety radar message will also be announced. See the Programming section for details.
Controls and Features Programming Power Connector Audible Alerts The Pro200’s power jack uses a telephonetype connector.This 4-conductor connector only works with the included power cord, optional Direct-wire, or SmartCord. For more information or to order, call us toll-free at 1-800-341-2288. For Radar signals: Your Pro200 uses a Geiger-counter-like sound to indicate the signal strength and type of radar signal being encountered.
Details of Programming Overview of Programming Press the REVIEW button to go from one category to the next Press the CHANGE button to change your setting within a category PILOT (Power-on indication) Pilot HWY Pilot H * Full word: Highway or AutoScan or City Letter: H or A or C VOICE Voice ON Voice OFF * Voice alerts on Voice alerts off POWER-ON SEQUENCE PwrOn STD PwrOn FST * Standard power-on sequence Fast power-on sequence aMute ON aMute OFF * AutoMute on AutoMute off AUTOMUTE CITY MODE SEN
Details of Programming Technical Details City Mode Sensitivity Bands City STD (Standard) In this setting, when you put your Pro200 in the City mode, X-band sensitivity is significantly reduced, to reduce annoyance from X-band intrusion alarms and motion sensors. (factory default) BandsDFT In this setting, all North American radar and laser frequencies are monitored.This is the factory setting and it is recommended that you use your Pro200 in this mode.
Technical Details Interpreting Alerts Although the Pro200 has a comprehensive warning system and this handbook is as complete as we can make it, only experience will teach you what to expect from your Pro200 and how to interpret what it tells you.The specific type of radar being used, the type of transmission (continuous or instant-on) and the location of the radar source affect the radar alerts you receive.
Technical Details How Radar Works Radar range also depends on the power of the radar equipment itself. The strength of the radar unit’s beam diminishes with distance.The farther the radar has to travel, the less energy it has for speed detection. Because intrusion alarms and motion sensors often operate on the same frequency as radar, your Pro200 will occasionally receive non-police radar signals.
Technical Details TSR Traffic Signal Rejection Software How Safety Radar Works Your radar detector includes a new optional boost in anti-falsing software to eliminate excessive alerts from erroneous X and K-band sources. One example of this is traffic flow monitoring systems.These systems, which are becoming more widely used in several countries, generate K-band signals to measure the flow of traffic on a given road. Unfortunately most detectors see this as a real threat and will alert you to it unnecessarily.
Troubleshooting Problem Solution Problem Solution The Pro200 beeps briefly at the same location every day, but no radar source is in sight. • An X or K-band motion sensor or intrusion alarm is located within range of your route.With time, you will learn predictable patterns of these signals. Your 14-year old son has changed all 6 of the Programming options. • You can return all of the programming options to the factory defaults by holding down the CITY and BRT buttons while you turn the Pro200 on.
Warranty and Accessories Service Service Procedure Out Of Warranty Repairs If your Pro200 ever needs service, please follow these simple steps: For out of warranty repairs, include prepayment in the amount you were quoted by the Beltronics Customer Service Representative. If the detector has been damaged, abused or modified, the repair cost will be calculated on a parts and labor basis. If it exceeds the basic repair charge, you will be contacted with a quotation.
