Owner's Manual

The Bel Pro200 is the most advanced radar,
laser and safety detector ever designed by
Beltronics.
The Bel Pro200 includes full X, K,
SuperWide Ka, and Safety Warning System
radar capability, front and rear laser
detection, varactor-tuned (VTO) microwave
receiver, digital signal processing (DSP)
for superior range and reduced false
alarms, our patented Mute and AutoMute,
audible and visual band alerts, and all the
performance you’d expect from Beltronics.
In addition, the Bel Pro200 introduces
the following revolutionary features:
• Varactor-tuned receiver provides
long-range protection against all
radar threats
• New easy-to-use Programming lets
you customize up to 6 features
• New AutoScan mode intelligently
reduces unwanted false alarms, plus
Highway and City settings
• Ultra-bright text-display provides
easy to read information from any
angle
• Detects and decodes Safety Warning
System messages
If you’ve used a radar detector before,
a review of the Quick Reference Guide on
pages 4 and 5, and the Programming
information on pages 12 and 13 will briefly
explain the new features.
If this is your first detector, please read
the manual in detail to get the most out of
your Pro200’s outstanding performance
and innovative features.
Please drive safely.
Congratulations Quick Reference
1
Programming Details 
An example
Here is how you would turn the Pro200’s AutoMute
feature off.
1 Enter the Program Mode by holding both the CITY
and BRT buttons down for 2 seconds. The Pro200
will beep twice and display
Program.
2 Then hold the RVW button down. Pro200 will
scroll through the categories, starting with Display
(Pilot), then Voice (Voice), then Power-On
sequence
(PwrOn), and then AutoMute (aMute).
3 Release the RVW button when the Pro200 shows
the AutoMute item. Since the factory setting is for
AutoMute to be on, the Pro200 will display
aMute ON.
If you accidentally don’t release the Review
button in time, and the Pro200 goes to the next
category, hold the RVW button down again, and
after the Pro200 scrolls through all categories, it
will begin again at the top of the list.
4 Press the CHG button to change from aMute ON to
aMute OFF.
5 To complete the Programming, simply wait 8
seconds without pressing any button.
The Pro200
will display
Complete, beep 4 times, and return to
normal operation.
There are 6 user-selectable options so you can
customize your Pro200 for your own preferences.
The buttons labeled CITY and BRT are also used to
enter the Program Mode, REVIEW your current
program settings, and to CHANGE any settings as
desired. The words PGM, RVW and CHG are located on
the top of the detector, and are highlighted in graphics.
How to use Programming
1 To enter Program Mode, press and hold both
CITY and BRT buttons down for 2 seconds. The
unit will beep twice, and will display the word
Program.
2 Then press the RVW button to review the
current settings. You can either tap the button to
change from item to item, or hold the button to scroll
through the items.
3 Press the CHG button to change any setting.
You can either tap the button to change from setting to
setting, or hold the button to scroll through all the
options.
4 To leave Program Mode, simply wait 8 seconds
without pressing any button. The unit will display
Complete, beep, and return to normal operation.
FCC Note:
Modifications not expressly approved
by the manufacturer could void the
user’s FCC granted authority to operate
the equipment.
Register
online:
@
www.beltronics.com
Factory Default Settings
To reset your Pro200 to its original factory settings,
press and hold the “CIT
Y” and “BRT” buttons
while turning the power on. The Pro200’s display
will provide a
Reset message, accompanied by an
audible alert, acknowledging the reset.