OWNER'S MANUAL
TABLE OF CONTENTS PRODUCT INFORMATION Unit & Parts...........................................................................................................4 PRODUCT INSTALLATION Seat Installation................................................................................................5 Remote Installation.......................................................................................8 PRODUCT OPERATION Functions & Settings....................................................................
UNIT & PARTS SEAT INSTALLATION 1. Attach Rubber Anchors 2. Attach the Mounting Plate Remove the existing toilet seat and insert the rubber anchors into the mounting holes. Place the catch plate and guides over the mounting holes. Insert the mounting screw and secure the catch plate to the toilet. 3. Attach the Bidet Seat 4. Seat Sensor Slide the bidet seat all the way on to the catch plate. You will hear a click once the product is securely mounted to the catch plate.
SEAT INSTALLATION (CONT.) 5. Connect the Water Hose 1. 6. Plug it in! • Plug the power cord into a 120V power outlet. • Please contact our service center at 847-458-2334 if you have any questions. Close the water shutoff valve. 2. Flush the toilet to empty the tank. 3. Remove the existing water supply hose from the tank. 4. Install the t-valve on to the tank. Ensure the rubber gasket is properly seated inside the T-Valve. 5. Connect the 7/8” water supply hose to the water shutoff valve and t-valve.
REMOTE INSTALLATION 1. Installation 2. Remote Pairing (Follow these instructions if the bidet seat is not responding to the remote) a. Unplug the bidet seat. b. Press and hold the “STOP” button on the remote until the indicator lights flash. a. Drill two 6mm holes on the wall that line up with the remote bracket. b. Install the wall anchors in the newly drilled holes with a hammer. c. Place the remote bracket over the wall anchors. c. Hold the remote close to the bidet seat and plug it back in. d.
FUNCTIONS & SETTINGS Turn On The Seat • Press the Power Button on the side of the seat. Pre Nozzle Rinse • As soon as the seat sensor is activated, a pre-rinse cycle will begin. This process rinses the nozzle in preparation for a wash function. Water will drain into the bowl during this time. Turn Sounds On/Off • Press and hold the night light button for 3 seconds to turn beeping sounds on/off. OPEN/CLOSE LID OPEN/CLOSE SEAT Press to open or close the lid. Press to open or close the seat.
FUNCTIONS & SETTINGS (CONT.) AIR TEMP | WATER TEMP. | SEAT TEMP. ULTRAVIOLET STERILIZATION Press the corresponding buttons to adjust the temperature settings on each feature. This feature automatically activates after a wash cycle. The seat cannot be used during this time. This feature can only be activated when the seat is not occupied. • Low - Blue • Medium - Purple • High - Red POWER/STOP BUTTON Short press to power on or long press to enter standby mode.
MAINTENANCE Cleaning the Unit • Disconnect the power plug and wipe the seat with a dry or damp cloth using a neutral cleaning solution. • Do not spray water directly on this product. • Do not use harsh cleaning chemicals, as those can cause damage or discoloration. Extended Travel When the seat will not be used for more than a few days, it is recommended to unplug the unit and turn off the water shutoff valve.
WARRANTY 2 YEAR WARRANTY Your product is warranted against defects in materials or workmanship for (2) years from the date of original purchase. Defective parts or a defective products returned to Bio Bidet Innovation LLC will be repaired with new or comparable rebuilt parts or exchanged for a refurbished product as determined by Bio Bidet Innovation LLC in their sole discretion.
SPECIFICATIONS Warning Model Haven 5000 Rated Power 1050W Rated Voltage 120V, 60Hz Waterproof Guide IPX4 Seat Temp 18 Off / 93.2~102.2°F Water Temp. Off / 95 ~ 102.2°F Product Dimensions 20.79” x 16.38” x 5.59” Ambient Temp Requirement 39.2 ~ 104° F Water Heating Instant Air Temp Off / 95-131°F • The product must be reliably grounded. Otherwise, electric shock may be caused by fault or short circuit. When in doubt, contact the electrical installation company.
SPECIFICATIONS (CONT.) • Persons (including children) with physical, perceptual, intellectual disabilities or lack of experience and common sense are requested to use the product in the company of someone. Otherwise use for a long time, may cause low temperature burns. • Children should not play with this product. Otherwise it may cause personal injury.
SPECIFICATIONS (CONT.) • Please do not pour newsprint, paper pad, sanitary napkin and other easily blocked articles into the toilet. • Please do not use in the environment below 0°C. • Do not hit the ceramic with gravity to prevent damage and leakage. • Please do not insert cementing materials (cement mortar, etc.) in the base of the toilet to prevent cracking due to expansion. • Please use the battery correctly according to the following methods.
Thank You Technical Support/Customer Service 7900 S Route 31 Crystal Lake, IL 60014 T: 847.458.2334 TOLL FREE: 877.339.5214 bidets@bemismfg.com www.toiletseats.