Manual

15
TABULATED DATA
TU-FLO
®
400 TU-FLO
®
500 TU-FLO
®
1000
Air Compressor Air Compressor Air Compressor
Number Cylinders 2 2 4
Bore Size 2.0625" 2.5" 2.5"
Stroke 1.5" 1.6875" 1.6875"
Displacement at 1,250 RPM 7.25 cu. ft./min. 12 cu. ft./min. 24 cu. ft./min.
Maximum recommended RPM 3,000 water cooled 3,000 water cooled 3,000 water cooled
2,400 air cooled 2,400 air cooled 2,400 air cooled
Minimum coolant flow at 2.5 gal./min. 2.5 gal./min. 2.5 gal./ min.
maximum RPM water cooled water cooled water cooled
250 CFM air flow 250 CFM air flow 250 CFM air flow
Approximate horsepower required
at 1,250 RPM 1.2 H.P. 2.3 H.P. 4.6 H.P.
Maximum inlet air temperature 250° F. 250° F. 250° F.
Maximum discharge air temperature 400° F. 400° F. 400° F.
Minimum pressure required
to unload 60 PSI 60 PSI 60 PSI
Minimum oil pressure required at
engine idling speed 5 PSI 5 PSI 5 PSI
Minimum oil pressure required at
maximum governed engine speed 15 PSI 15 PSI 15 PSI
Approximate average weight 34 lbs. 46 lbs. 75 lbs.
Oil capacity of self-lubricated model .53 qts. .53 qts. .95 qts. to 5 qts.*
Minimum discharge line size 1/2" O.D. tubing 5/8" O.D. tubing 5/8" O.D. tubing or equivalent
or equivalent or equivalent from each head to a common
manifold with 1" tubing from
manifold.
Minimum coolant line size 3/8" O.D. tubing 1/2" O.D. tubing 1/2" O.D. tubing
or equivalent or equivalent or equivalent
Minimum oil supply line size 1/4" O.D. tubing 1/4" O.D. tubing 1/4" O.D. tubing
or equivalent or equivalent or equivalent
Minimum oil return line size 1/2" O.D. tubing 5/8" O.D. tubing 5/8" O.D. tubing
or equivalent or equivalent or equivalent
**Minimum air inlet line size 5/8" I.D. 5/8" I.D. 1" I.D. if equipped with inlet
manifold; or, dual 5/8" I.D. lines
from engine to compressor inlets.
*Part Number dictates oil capacity
**Inlet line sizes specified for compressors with inlet connected to engine manifold.
MAINTENANCE INSTRUCTIONS FOR
LARGE SUMP TU-FLO
®
1000 AIR
COMPRESSOR 288578 (SPECIAL
APPLICATION)
This compressor is an air-cooled, belt driven, self lubricated,
V-four cylinder compressor. It is driven by an electric motor
and cooling air is supplied by a fan on the driven pulley. The
system air pressure is controlled between 135 psi and 150
psi by a pressure switch starting and stopping the electric
motor.
INSTALLATION
The base mounted compressor should be securely bolted
down with 1/2" grade five or better cap screws torqued to 70
ft. pounds, making sure that motor and compressor pulleys
are aligned and belt tension is correct. The crankcase should
be filled with five quarts (4.7 liter) of SAE 20 W engine oil.
The compressor must always be installed to rotate clockwise
when viewed from the pulley end. The oil pump will not
function if rotation is not correct.
SCHEDULED MAINTENANCE
NOTE: When checking or adding oil or servicing the
crankcase breather, care should be taken to prevent
dirt or foreign material from entering the breather or
oil sump.
Every 7,500 miles or seven weeks, whichever occurs first:
Check oil level - replenish to top of filler plug opening.
Replace both air cleaner filter elements and clean covers.
Check belts and replace if broken, damaged or missing.
Every 15,000 miles or 14 weeks, whichever occurs first:
Remove crankcase ventilator, clean ports and replace with
freshly oiled curled hair.
Every 22,500 miles or 21 weeks, whichever occurs first:
Drain oil and refill with fresh SAE 20 W engine oil. Inspect
all bolts, fittings and plugs to ensure that all are tight.