D I S H WA S H E R BDW 10 822 90 11-50 INSTRUCTION BOOKLET
Contents For the installer For the user Important safety information Care and cleaning 3 Technical specifications 12 4-5 Unpacking the machine 13 - If the machine is damaged - Use - Protecting the machine against freezing - General cleaning - Rinse aid dispenser - Spray arm - Coarse filter - Fine filter - Detergent dispenser - Water softener - Water softener plug - Cleaning the cabinet Installation - Water inlet - Water drainage - Power supply The control panel 6 How to load the dishwasher 7
Important safety information Before installing and first using the dishwasher, read the instruction booklet carefully, including its hints and warnings. Doing so will ensure that your machine will perform properly and to best advantage. Anyone using the machine should be thoroughly familiar with its instructions for use and safety features.
Care and cleaning 2 1 6 3 4 5 Important Spray arm (2) Make sure that the machine is unplugged and the water turned off before undertaking any kind of maintenance. Inspect the filters and spray arm nozzle before re-loading the machine and remove any food scraps. Wipe round the rubber gasket at the bottom of the door to remove grease which tends to collect there. The holes in the spray arm nozzle must be kept clean to ensure satisfactory wash results. Inspect the spray arm regularly.
Detergent dispenser (5) Cleaning the cabinet Only use detergents specially designed for dishwashers. Pour the detergent into the compartment, for a normal load pour about 15g. Since not all detergents are the same, you should also consult the instructions on the packet. Remember that the instructions usually refer to full-size dishwashers, for example when using detergent tablets, it is sufficient to use just half a tablet. Using the correct amount of detergent also contributes to reducing pollution.
The control panel 1 1 4 3 Temperature selector 55° - Button in 65° - Button out 2 Wash phase Programme knob To start the machine: Turn the selector knob clockwise to the programme start. The On/Off switch is built into the programme timer. During the water heating process, the timer is standing still. To isolate the dishwasher from the mains completely, unplug it from the wall socket.
How to load the dishwasher The illustration shows the machine loaded with five standard place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. 1 • Always place glasses, cups and bowls upside down. • Incline deep dishes (soup plates etc.) so that the water can run off when drying. • Make sure that the dishes do not rest against each other.
Using your appliance 1 2 3 4 5 6 Proceed as follows: 1. Scrape off solid food remnants. 2. Load the dishwasher. (See “How to load the dishwasher”). Pour approx. 15 g detergent into the detergent dispenser. 3. Close the door. 4. Select the required temperature. 5. Start the dishwasher by turning the programme knob to the start position. 6. Check the filters to see whether they need cleaning when the dishwasher has finished the wash.
Something Not Working? Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check The machine will not start.
Service Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Guarantee Conditions Standard guarantee conditions We, Bendix, undertake that if within 12 months of the date of the purchase this BENDIX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity supply stated on the rating plate • The appliance has been used for
Installation instructions Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.
Unpacking the machine If the machine is damaged If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. Check that the dishwasher is undamaged. If you discover any damage, faults or that anything is missing, you should notify the dealer immediately. Never leave packaging material in a place where children may play with it.
Installation The dishwasher is intended for installation on a kitchen sink or worktop. It is important to ensure the dishwasher is level to avoid any difficulty opening and closing the door. Its height can be adjusted with the adjustable feet (8 mm each) in each corner of the dishwasher. Water inlet The dishwasher should be permanently plumbed into a separate cold water supply.
Power supply The dishwasher is supplied with a lead and electrical plug for connection to a 230 V, 13 A earthed wall socket. Before any work is carried out on the dishwasher, it must be isolated from the electric mains supply, for example by removing the plug from the wall socket. Permanent electrical installation must be carried out by an authorised electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed.
© Electrolux plc 2003
