SD-01-331 ® Bendix® BX-2150™ Air Compressor AIR OUTLET (2) (1 NOT SHOWN) WATER OUTLET UNLOADER STOP WATER INLET (NOT SHOWN) AIR INLET UNLOADER PISTON WATER OUTLET INLET VALVE UNLOADER PORTS AIR OUTLET AIR INTAKE DISCHARGE VALVE PISTON RINGS PISTON REAR END COVER CONNECTING ROD OIL INLET CRANKSHAFT SLEEVE BEARING OIL SEAL ROLLER BEARING BX-2150™ AIR COMPRESSOR BELT DRIVE MODEL DESCRIPTION GENERAL The function of the air compressor is to provide and maintain air under pressure to operate devices
1/2” P.T. WATER PORT (3) OUTLET WATER ONLY PART NUMBER 1/2” P.T. AIR DISCHARGE (2) SERIAL NUMBER TYPICAL NAMEPLATE 1/8” P.T. GOVERNOR PORT 2 PLACES AIR INLET 1/2” P.T. WATER PORT BX-2150™ COMPRESSOR CYLINDER HEAD pipe threads in each of the two governor mounting pads allow plugging of the unused port or the installation of a tubing fitting for remote governor mounting. Three 1/2” N.P.T. ports provide the means for the connection of coolant lines and are labeled WATER. Two 1/2” N.P.T.
VALVE STOP UNLOADER PISTON INLET INLET VALVE TO RESERVOIR DISCHARGE VALVE PISTON FIGURE 2 - COMPRESSION/DISCHARGE CYCLE cylinder bore as the intake and compression cycle is repeated. NON-COMPRESSION OF AIR (UNLOADED) When air pressure in the reservoir reaches the cut-out setting of the governor, the governor allows air to flow from the reservoir into the unloader piston cavity.
The Air Brake Charging System supplies the Discharge Line Optional “Ping” Tank Air Dryer compressed air for the braking system as well as other air accessories for the vehicle. The system usually consists of an air compressor, governor, discharge line, air dryer, and service reservoir.
The cylinder bore, connecting rod wrist pin bushing and ball type main bearing, where used, are splash lubricated. Splash lubrication is obtained as oil is forced out around the crankshaft journals by engine oil pressure. See the tabulated technical data in the back of this manual for specific requirements.
Inlet gasket 243430 is required between the inlet check valve reed and the inlet cavity of new style heads, or between the inlet check valve reed and the inlet adapter 297871 for old style heads, as its thickness contributes to the minimum reed travel required. The pin in the check valve seat must align with the holes in the check valve, the inlet gasket and enter the mating hole in the head or the inlet adapter.
COMPRESSOR COOLING Every six months, 1800 operating hours or 50,000 miles, whichever occurs first, inspect the compressor discharge port, inlet cavity and discharge line for evidence of restrictions and carboning. If excessive buildup is noted, thoroughly clean or replace the affected parts and closely inspect the compressor cooling system. Check all compressor coolant lines for kinks and restrictions to flow. Minimum coolant line size is 3/8" I.D. Check coolant lines for internal clogging from rust scale.
NO. 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 12 1 13 CYLINDER HEAD ASSY.
as to leakage, it is recommended that a genuine Bendix unloader kit be installed and the cylinder head retested. DISCHARGE VALVE LEAKAGE Unloader piston leakage must be repaired before this test is performed. Leakage past the discharge valve can be detected by removing the discharge line, applying shop air to the unloader mechanism and the discharge port and listening for the escape of air at the compressor inlet cavity.
6. Remove the drive gear(s) or pulley from the compressor crankshaft using a gear puller. Inspect the pulley or gear and associated parts for visible wear or damage. Since these parts are precision fitted, they must be replaced if they are worn or damaged. PREPARATION FOR DISASSEMBLY cylinder head body be replaced if it is determined that the unloader piston bushing requires replacement.
CLEANING OF PARTS PISTONS GENERAL Check the piston for scores, cracks, or enlarged ring grooves; replace the piston if any of these conditions are found. Measure the diameter of the top of the piston and the top two ring lands. (Compare to cylinder bore and piston diameters to be sure the diametrical clearance is between .0128 inch minimum and .0177 inch maximum.) All parts should be cleaned in a good commercial grade solvent and dried prior to inspection.
CONNECTING RODS ™ The BX-2150 compressor connecting rod does not incorporate replaceable crankshaft journal bearing inserts and must be replaced if excessively worn. Clearance between the crankshaft journal and the connecting rod bearing must not be less than .001 inch or more than .0025 inches. REPAIRS It is generally recommended that genuine Bendix service parts and maintenance kits be used whenever the compressor is disassembled.
3. Place the o-ring seal in the groove around the rear end cover or in the crankcase proper in the event a rear main ball bearing is in use. If the rear end cover contains a precision sleeve bearing that serves as the crankshaft main bearing, make certain to install the thrust bearing. Install the end cover in the position as marked before disassembly, taking care not to damage the sleeve bearing, if so equipped. 4.
TESTING REBUILT COMPRESSOR WATER PORT In order to properly bench testa compressor under operating conditions, a test rack for correct mounting, cooling, lubricating, and driving the compressor is necessary. Such tests are not compulsory if the unit has been carefully rebuilt by an experienced person. A compressor efficiency or build-up test can be run which is not too difficult. The compressor must be connected to an oil supply line of at least 15 P.S.I.
This troubleshooting guide obsoletes and supersedes all previous published troubleshooting information relative to Bendix air compressors. Advanced Troubleshooting Guide for Air Brake Compressors * The guide consists of an introduction to air brake charging system components, a table showing recommended vehicle maintenance schedules, and a troubleshooting symptom and remedy section with tests to diagnose most charging system problems.
Introduction to the Air Brake Charging System Powered by the vehicle engine, the air compressor builds the air pressure for the air brake system. The air compressor is typically cooled by the engine coolant system and lubricated by the engine oil supply.
Table A: Maintenance Schedule and Usage Guidelines Regularly scheduled maintenance is the single most important factor in maintaining the air brake charging system. Vehicle Used for: No. of Axles Column 1 Column 2 Typical Compressors Spec'd Discharge Line I.D. Length 1/2 in. 6 ft. Column 3 Recommended Air Dryer Cartridge Replacement1 Column 4 Recommended Reservoir Drain Schedule2 Column 5 Acceptable Reservoir Oil Contents3 at Regular Drain Interval e.g.
Air Brake Charging System Troubleshooting How to use this guide: Find the symptom(s) that you see, then move to the right to find the possible causes (“What it may indicate”) and remedies (“What you should do”). Review the warranty policy before performing any intrusive compressor maintenance. Unloader or cylinder head gasket replacement and resealing of the bottom cover plate are usually permitted under warranty. Follow all standard safety procedures when performing any maintenance.
Symptom: What it may indicate: What you should do: 2.0 Oil on the Outside of the Compressor Engine and/or other accessories leaking onto compressor. Find the source and repair. Return the vehicle to service. 2.1 Oil leaking at compressor / engine connections: (a)Leak at the front or rear (fuel pump, etc.) mounting flange. ð Repair or replace as necessary. If the mounting bolt torques are low, replace the gasket. (b)Leak at air inlet fitting. ð Replace the fitting gasket.
Symptom: What it may indicate: 4.0 Oil in Supply or Service Reservoir (air dryer installed) What you should do: Maintenance (a) If air brake charging system maintenance has not been (If a maintained Bendix performed.
Symptom: What it may indicate: 4.0 Oil in Supply or Service Reservoir* (air dryer installed) (continued) What you should do: Temperature (e) Air compressor discharge and/or air dryer inlet temperature too high. ð Check temperature as outlined in Test 3 on page 28. If temperatures are normal go to 4.0(h). (f) Insufficient coolant flow. ð Inspect coolant line. Replace as necessary (I.D. is 1/2"). ð Inspect the coolant lines for kinks and restrictions and fittings for restrictions. Replace as necessary.
Symptom: 4.0 Oil in Supply or Service Reservoir* (air dryer installed) (continued) What it may indicate: What you should do: Other (cont.) (i) Poorly filtered inlet air (poor air quality to compressor). Inspect the engine air cleaner. ð Check for leaking, damaged or defective compressor air inlet components (e.g. induction line, fittings, gaskets, filter bodies, etc.). Repair inlet components as needed. Note: Dirt ingestion will damage compressor and is not covered under warranty.
Symptom: What it may indicate: What you should do: 6.0 Excessive oil consumption in engine. A problem with engine or other engine accessory. ð See engine service manual. 7.0 Oil present at air dryer cartridge during maintenance. Air brake charging system is functioning normally. The engine service manual has more information. Oil shown leaking from an air dryer cartridge. ð Air dryers remove water and oil from the air brake charging system. A small amount of oil is normal.
Symptom: 9.0 Air brake charging system seems slow to build pressure. (continued) What it may indicate: What you should do: (f) Restricted discharge line. ð If discharge line is restricted: ð By more than 1/16" carbon build up, replace the discharge line (see Table A, column 2, on page 17 for recommended size) and go to Test 3 on page 28. ð By other restrictions (e.g. kinks). Replace the discharge line. See Table A, column 2, on page 17 for recommended size. Retest for air build.
Symptom: 10.0 Air charging system doesn’t build air. What it may indicate: What you should do: (a) Governor malfunction*. ð Go to Test 4 on page 29. (b) Restricted discharge line. ð See 9.0(f). (c) Air dryer heater malfunction: exhaust port frozen open. ð Replace air dryer heater. (d) Compressor malfunction. ð Replace the compressor only after making certain the preceding conditions do not exist.
Symptom: 12.0 Air dryer safety valve releases air. What it may indicate: What you should do: (a) Restriction between air dryer and reservoir. ð Inspect delivery lines to reservoir for restrictions and repair as needed. (b) Air dryer safety valve malfunction. ð Verify relief pressure is at vehicle or component manufacturer specifications. Replace if defective. (c) Air dryer performed. ð See Maintenance Schedule and Usage Guidelines (Table A, column 3, on page 17).
Symptom: 16.0 Compressor leaks air What it may indicate: (a) Compressor leaks connections or ports. at ð Check for leaking, damaged or defective compressor fittings, gaskets, etc. Repair or replace as necessary. ð Go to Test 6 on page 29. (c) Damaged gasket. head ð An air leak at the head gasket may indicate a downstream restriction such as a freezeup or carbon blockage and/or could indicate a defective or missing safety valve. Find blockage (go to 9.0(f) for details.) and then replace the compressor.
Tests Test 1: Excessive Oil Leakage at the Head Gasket Exterior leaks at the head gasket are not a sign that oil is being passed into the air charging system. Oil weepage at the head gasket does not prevent the compressor from building air. Observe the amount of weepage from the head gasket. If the oil is only around the cylinder head area, it is acceptable (return the vehicle to service), but, if the oil weepage extends down to the nameplate area of the compressor, the gasket can be replaced.
Tests (continued) Test 4: Governor Malfunction 1. Inspect control lines to and from the governor for restrictions (e.g. collapsed or kinked). Repair as necessary. 2. Using a calibrated external gauge in the supply reservoir, service reservoir, or reservoir port of the D-2™ governor, verify cut-in and cutout pressures are within vehicle OEM specification. 3. If the governor is malfunctioning, replace it. Test 5: Governor Control Line 1.
Appendix A: Information about the BASIC Test Kit (Bendix P/N 5013711) Service writer records info - including the number of days since all air tanks were drained - and fills out symptom checklist. Technician inspects items. days Bendix® Air System Inspection Cup (BASIC) Test Information START BASIC TEST Park vehicle on LEVEL ground. Chock wheels, drain air from system. Drain contents of ALL air tanks into BASIC cup Is there less than one unit of liquid? Vehicle OK. Return vehicle to service.
Appendix A continued: Information about the BASIC Test Kit (Bendix P/N 5013711) ® Filling in the Checklist for the Bendix Air System Inspection Cup (BASIC) Test Note: Follow all standard safety precautions. For vehicles using a desiccant air dryer.
Appendix A continued: Information about the BASIC Test Kit (Bendix P/N 5013711) ® Filling in the Checklist for the Bendix Air System Inspection Cup (BASIC) Test Note: Follow all standard safety precautions. For vehicles using a desiccant air dryer. 2. Record amount of oil found: The Technician uses the chart (label) on the BASIC test cup to help decide the action to take, based on the amount of oil found.
Appendix B Technical Bulletin Bulletin No.: TCH-008-021 Subject: Effective Date: 11/1/92 Page: 1 of 2 Air Brake System - Cold Weather Operation Tips As the cold weather approaches, operators and fleets alike begin to look to their vehicles with an eye toward “winterization”, and particularly what can be done to guard against air system freeze-up. Here are some basic “Tips” for operation in the cold weather.
Appendix B: Continued Bulletin No.: TCH-008-021 Effective Date: 11/1/92 Page: 2 of 2 High Duty Cycle Vehicles (City Transit Coaches, Refuse Haulers, Etc.) The maximum discharge line length is 16 feet. Length I.D. min. Other Requirements 10-16 ft. ½ in. None If the discharge line length must be less than 10 feet or greater than 16 feet, contact your local Bendix representative.
Appendix B: Continued Technical Bulletin Bulletin No.: TCH-008-022 Subject: Additional Effective Date: 1/1/1994 Page: 1 of 1 Cold Weather Operation Tips for the Air Brake System Last year we published Bulletin PRO-08-21 which provided some guidelines for “winterizing” a vehicle air brake system. Here are some additional suggestions for making cold weather vehicle operation just a little more bearable.
BW1424 © 2004 Bendix Commercial Vehicle Systems LLC All rights reserved. 9/2004 Printed in U.S.A.
