User's Manual

23
$LU'LVF%UDNH$WWDFKPHQW+DUGZDUH
7RUTXH3ODWH0DQXIDFWXUHU )DVWHQHU 7RUTXH
%HQGL[$[LDO
&DUULHU7RUTXH3ODWH
)DVWHQHU0[[PP&ODVV
Washer: Requires HARDENED 3 mm
(minimum thickness) for each bolt.
1
If the vehicle is using a Bendix
manufactured Axial Anchor Plate, with a
thickness of 1.14 in. (29 mm) where these
bolts are assembled, then a bolt with an
overall length of 2.36 in. (60 mm) will meet
these requirements
8VHWKHPDQXIDFWXUHU¶VUHFRPPHQGDWLRQV
,IXQDYDLODEOHXVHSKRVSKDWH
DQGRLO¿QLVKIDVWHQHU
3UH7RUTXHIWOEI>1ÂP@
)LQDO7RUTXHIWOEI>1ÂP@
%HQGL[9HUWLFDO
&DUULHU7RUTXH3ODWH
)DVWHQHU0[[PP&ODVV
Washer: None required.
8VHWKHPDQXIDFWXUHU¶VUHFRPPHQGDWLRQV
,IXQDYDLODEOHXVHSODLQDQGRLO¿QLVKIDVWHQHU
7RUTXHIWOEI>1ÂP@
7UDLOHU7RUTXH3ODWH
)DVWHQHU0[[/&ODVV
/HQJWKGHWHUPLQDWLRQ
/ 7RUTXH3ODWH73WKLFNQHVV&DUULHU
HQJDJHPHQW:DVKHUWKLFNQHVV
L
PLQ
 73WKLFNQHVVPPPP
L
PD[
 73WKLFNQHVVPPPP
Washer: Requires HARDENED 3 mm
(minimum thickness) for each bolt.
1
8VHWKHPDQXIDFWXUHU¶VUHFRPPHQGDWLRQV
,IXQDYDLODEOHXVHSKRVSKDWH
DQGRLO¿QLVKIDVWHQHU
3UH7RUTXHIWOEI>1ÂP@
)LQDO7RUTXHIWOEI>1ÂP@
Table Note: 1. The washer outside diameter must be less than 1.1in. (28.5 mm).
TABLE 4 - TORQUE PLATE FASTENERS AND TORQUE RECOMMENDATIONS (SEE MANUFACTURER’S RECOMMENDATIONS)
 ,IWKHEUDNHDVVHPEO\GRHVQRWVHSDUDWHIURPWKH
DQFKRUSODWHLWPD\EHKHOSIXOWRLQVWDOODQ0;
VFUHZORQJHUWKDQPPDWWKHEXVKLQJORFDWLRQV
DQGWDSWKHHQGRIWKHEROWZLWKDKDPPHUWRIUHH
WKHEUDNHDVVHPEO\5HPRYHWKHDVVHPEO\
Axial Mounting Bolt Style
 'LVFRQQHFWWKHDLUKRVHVWRWKHEUDNHFKDPEHU
See Figure 42.6XSSRUWLQJWKHDLUGLVFEUDNHE\
QHFHVVDU\PHDQVUHPRYHWKHVL[EROWVDWWDFKLQJ
WKH EUDNH WR WKH DQFKRU SODWH DQG UHPRYH WKH
FDOLSHUFDUULHUDVVHPEO\IURPWKHYHKLFOH
Note: Bendix strongly recommends that during re-assembly
these bolts and washers are replaced. See your vehicle
manufacturer for replacement hardware. Remove the
assembly.
Re-installation (Both Styles)
 6XSSRUWLQJWKHDLUGLVFEUDNHE\QHFHVVDU\PHDQV
DWWDFK WKH EUDNH WR WKH DQFKRU SODWH XVLQJ VL[
QHZ EROWV  7RUTXH WR YHKLFOH PDQXIDFWXUHU¶V
VSHFL¿FDWLRQV,IWRUTXHYDOXHVDQGEROWVDUHQRW
VSHFL¿HGE\WKHYHKLFOHPDQXIDFWXUHUWKHQVHOHFW
DUHSODFHPHQWEROWDVVKRZQLQ7DEOH
Anchor Plate/
Torque Plate
Caliper/Carrier
Assembly
(Actuator not
shown)
Mounting Bolts
and Washers
(6 sets total)
FIGURE 42 - AXIAL MOUNT CALIPER/CARRIER
 5HLQVWDOOWKHDLUKRVHV(See Section 5.4.8-9) and
check for leaks
 ,QVSHFWDQGUHLQVWDOOWKHSDGV(See Section 5.2)