User's Manual

37
5HLQVWDOO WKH DLU GLVF EUDNH (See Section 5.3).
6XSSRUWLQJ WKH DLU GLVF EUDNH E\ DOO QHFHVVDU\
PHDQV DWWDFK WKH EUDNH WR WKH DQFKRU SODWH
XVLQJ VL[ EROWV DQG ZDVKHUV DV UHTXLUHG %HQGL[
UHFRPPHQGV WKH RULJLQDO EROWV QRW EH UHXVHG
7RUTXH WR YHKLFOH PDQXIDFWXUHUV VSHFL¿FDWLRQV
,IWRUTXHYDOXHVDQGEROWVDUHQRWVSHFL¿HGE\WKH
YHKLFOHPDQXIDFWXUHUWKHQWRUTXHDFFRUGLQJWRWKH
FKDUWEHORZ%HVXUHWRVHOHFWEROWVZLWKWKHVDPH
WKUHDGSLWFKOHQJWKDQGJUDGHDVRULJLQDOO\SURYLGHG
IURPYHKLFOHPDQXIDFWXUHU
5HLQVWDOOWKHEUDNHSDGV(See Section 5.2).
FIGURE 91 - FASTENERS INSTALLED
$LU'LVF%UDNH$WWDFKPHQW+DUGZDUH
7RUTXH3ODWH0DQXIDFWXUHU )DVWHQHU 7RUTXH
%HQGL[$[LDO
&DUULHU7RUTXH3ODWH
)DVWHQHU0[[PP&ODVV
Washer: Requires HARDENED 3 mm
(minimum thickness) for each bolt.
1
If the vehicle is using a Bendix
manufactured Axial Anchor Plate, with a
thickness of 1.14 in. (29 mm) where these
bolts are assembled, then a bolt with an
overall length of 2.36 in. (60 mm) will meet
these requirements
8VHWKHPDQXIDFWXUHU¶VUHFRPPHQGDWLRQV
,IXQDYDLODEOHXVHSKRVSKDWH
DQGRLO¿QLVKIDVWHQHU
3UH7RUTXHIWOEI>1ÂP@
)LQDO7RUTXH
IWOEI>1ÂP@
%HQGL[9HUWLFDO
&DUULHU7RUTXH3ODWH
)DVWHQHU0[[PP&ODVV
Washer: None required.
8VHWKHPDQXIDFWXUHU¶VUHFRPPHQGDWLRQV
,IXQDYDLODEOHXVHSODLQDQGRLO¿QLVKIDVWHQHU
7RUTXHIWOEI>1ÂP@
7UDLOHU7RUTXH3ODWH
)DVWHQHU0[[/&ODVV
/HQJWKGHWHUPLQDWLRQ
/ 7RUTXH3ODWH73WKLFNQHVV&DUULHU
HQJDJHPHQW:DVKHUWKLFNQHVV
L
PLQ
 73WKLFNQHVVPPPP
L
PD[
 73WKLFNQHVVPPPP
Washer: Requires HARDENED 3 mm
(minimum thickness) for each bolt.
1
8VHWKHPDQXIDFWXUHU¶VUHFRPPHQGDWLRQV
,IXQDYDLODEOHXVHSKRVSKDWH
DQGRLO¿QLVKIDVWHQHU
3UH7RUTXHIWOEI>1ÂP@
)LQDO7RUTXHIWOEI>1ÂP@
Table Note: 1. The washer outside diameter must be less than 1.1in. (28.5 mm).
TABLE 7 - TORQUE PLATE FASTENERS AND TORQUE RECOMMENDATIONS (SEE MANUFACTURER’S RECOMMENDATIONS)