CONTENTS Page Number Description Warranty Policy............................................................................................................................... Contents - Part Number to Page Number...................................................................................... Air Brake System Color Chart....................................................................................................... Air Brake System Troubleshooting...............................................
CONTENTS Page Description Number ® Bendix Remanufactured Air Valve Section (Continued)............................................................ 82-94 Haudraulic Relay Valve (HR-1)......................................................................................... Modulating Valve (R-7)..................................................................................................... Pressure Equalizing Valve (R-8P)....................................................................................
CONTENTS Page Number Description Midland® Remanufactured Air Compressor Pictoral Guide (Continued).................................... 112-112 Midland® Head Assemblies............................................................................................... 112 Midland® Remanufactured Air Valve Pictoral Guide................................................................... Air Valve Crossover..........................................................................................................
CONTENTS Page Number Description Williams® New and Remanufactured Air Valve Pictoral Guide (Continued)............................... Safety Valve...................................................................................................................... Air Throttle Valves............................................................................................................. Regulator Panel Valve...............................................................................................
CONTENTS (Part Number to Page Number) Part Number Page Number Part Number 100708 148 290997 149 291054 104738 Page Number Part Number Page Number Part Number Page Number 15 342501X 143 065212X 76 15 3450SX 143 065214X 76 94 105373 149 291172 15 3558000X 96 065229X 105374 149 291357 15 3558006X 97 065230X 94 105375 149 10005AX 134 5900-1X 142 065231X 94 106704 149 1070MK 152 6125-2X 142 065248X 72 106706 149 10900X 145 6300X 145 109977X 69 106841
CONTENTS (Part Number to Page Number) Part Number Page Number Part Number Page Number Part Number Page Number Part Number Page Number 102989X 35 107813X 47 110460X 134 228750X 91 103009X 81 107866X 35 110470X 134 229077X 30 103010X 82 107869X 50 110475X 134 229078X 33 103028X 82 108076X 79 110500X 140 229434X 84 103061X 79 108233X 74 110505X 140 229467X 80 103081X 83 108804X 42 110510X 140 229493X 91 103139X 82 109264X 83 110575X 135 229500X 66
CONTENTS (Part Number to Page Number) Part Number Page Number Part Number Page Number Part Number Page Number Part Number Page Number 277226X 87 280622X 41 284358X 66 286564X 33 277227X 87 280626X 41 284412X 86 286565X 33 277340X 88 280651X 80 284662X 47 286566X 38 277446X 84 280743X 91 284699X 41 286567X 34 277730X 38 280758X 88 284714X 41 286574X 49 277731X 38 280809X 89 284744X 71 286576X 35 277765X 73 280904X 74 284760X 68 286578X 35 277863
CONTENTS (Part Number to Page Number) Part Number Page Number Part Number Page Number Part Number 288239X 71 A3546X 98 KN13060X 106 KN20020X 116 288241X 71 A4487 100 KN13070X 110 KN20030X 116 288242X 71 A4490 100 KN13080X 107 KN20030AX 116 288251X 76 A4491 100 KN13081X 107 KN20040X 117 288301X 85 A4688X 98 KN13090X 110 KN20050X 117 288323X 87 A4900 99 KN13100X 110 KN20060X 117 288369X 81 A5010 99 KN13110X 111 KN20071X 119 288383X 68 A5015 99 K
CONTENTS (Part Number to Page Number) Part Number Page Number Part Number Page Number New Page MV-3 (New) Information 154 Cummins® and Holset® Air Compressors Rorochambers 155 155 New Valves & Products 156 - 159 Air Dryers, Cartridges, & Kits 160 - 161 Remanufactured Calipers 162 Lucus Girling® System 163 Fan Clutches 164 KN28085X 123 KN7030X 104 KN28130X 123 KN7040X 105 KN28131X 123 KN7041X 105 KN28132X 122 KN7050X 105 KN28140X 122 KN7070X 109 KN28150X 125 KN7080X
AIR BRAKE SYSTEM TROUBLESHOOTING QUALITY HEAVY DUTY PARTS Page 10 04_26125_pg10-11.
AIR BRAKE SYSTEM TROUBLESHOOTING QUALITY HEAVY DUTY PARTS 04_26125_pg10-11.
AIR BRAKE SYSTEM TROUBLESHOOTING 1.) Before replacing any valve with a new or remanufactured valve, be sure to blow the air lines out either using the vehicle’s own air supply or shop air. Dirt is the greatest cause of premature air valve failure. 2.) If pipe dope is used on fittings, use it sparingly. This can also get into the unit and cause a failure. 3.) When installing fittings into a remanufactured valve, do not over tighten or it will crack the casting. 4.
AIR BRAKE SYSTEM TROUBLESHOOTING 1.) Before replacing any valve with a new or remanufactured valve, be sure to blow the air lines out either using the vehicle’s own air supply or shop air. Dirt is the greatest cause of premature air valve failure. 2.) If pipe dope is used on fittings, use it sparingly. This can also get into the unit and cause a failure. 3.) When installing fittings into a remanufactured valve, do not over tighten or it will crack the casting. 4.
AIR BRAKE SYSTEM TROUBLESHOOTING PROBLEM CAUSE REMEDY 1) Dryer is constantly cycling or purging. a. Excessive system leak. b. Defective governor. c. Defective one way valve between air dryer and wet tank. d. Kinked or plugged discharge line. 2) Water and sludge appear in wet tank. a. Plugged desiccant cartridge or filter. a. Replace dessicant cartridge filter. b. Use minimum of six-foot tubing for twob. Improper length or material of cylinder compressor; ten-foot for one cylinder discharge line.
REPLACEMENT KNOBS FOR DASH CONTROL VALVES 243953 244282 PULL TO APPLY 240920 PUSH TO CHARGE PULL FOR NORMAL TRAILER TRAILER CONTROL RESERVE AIR EMERGENCY BRAKE CONTROL PUSH TO RELEASE PUSH TO RELEASE AUXILIARY BRAKE PUSH TO RELEASE NOT FOR PARKING 248437 240302 PULL TO APPLY PULL TO PARK PARKING BRAKE PUSH TO RELEASE PUSH TO RELEASE 248433 245841 245186 EMERGENCY BRAKE PULL TO APPL Y APPLY 240931 PUSH AND HOLD BRAKE RELEASE 248434 247348 248435 PULL TO APPLY TRAILER EMERGENCY
BENDIX® - AIR COMPRESSORS O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E.
BENDIX® - AIR COMPRESSORS REMAN / SERVICE REMAN / SERVICE TU FLO MODEL O.E.
BENDIX® - AIR COMPRESSORS O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E.
BENDIX® - AIR COMPRESSORS REMAN / SERVICE TU FLO MODEL 276112 276113 276136 276143 276148 227323X 227324X 276166X 227401X 227321X 500 500 400 500 500 277058 277073 277082 277097 277098 227322X 275114X 227400X 277097X 277098X 1000 400 400 1000 400 276166 276167 276168 276169 276220 289444X 276961X 228083X 276166X 276476X 400 500 400 400 500 277099 277111 277122 277123 277127 227406X 275231X 229078X 275271X 229990X 400 500 500 500 1000 276236 276257 276258 276259 276260 277730X 227326X 227328X
BENDIX® - AIR COMPRESSORS O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E.
BENDIX® - AIR COMPRESSORS O.E. NUMBER REMAN / SERVICE TU FLO MODEL REMAN / SERVICE TU FLO MODEL O.E.
BENDIX® - AIR COMPRESSORS O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E. NUMBER REMAN / SERVICE TU FLO MODEL O.E. REMAN / NUMBER SERVICE TU FLO MODEL O.E.
BENDIX® - AIR COMPRESSORS REMAN / SERVICE TU FLO MODEL 289388 289400 289401 289402 289826 289388X 289388X 289498X 275317X 101661X 400 400 400 400 400 400 600 600 600 600 289404 289405 289406 289407 289408 289443X 227407X 289443X 289819X 227407X 288734X 289964X 227407X 286581X 288890X 500 600 400 501 500 289408 289409 289410 289411 289412 288906 288930 288942 288951 288952 286546X 288930X 286582X 286546X 277694X 501 1000 501 501 500 600 501 600 501 501 288974 288975 288982 288982 288989 28652
BENDIX®- AIR COMPRESSORS AIR COMPRESSOR SIZES and CFM BX-2150 TU-FLO 400 TU-FLO 500 TU-FLO 501 9.5 CFM AT 1250 RPM 7.25 CFM AT 1250 RPM 12 CFM AT 1250 RPM 12 CFM AT 1250 RPM TU-FLO 550 TU-FLO 600 TU-FLO 700 TU-FLO 750 13.2 CFM AT 1250 RPM 14.5 CFM AT 1250 RPM 15.5 CFM AT 1250 RPM 16.5 CFM AT 1250 RPM TU-FLO 1000 TU-FLO 1400L 24 CFM AT 1250 RPM 31 CFM AT 1250 RPM WE REMANUFACTURE QUALITY HEAVY DUTY AIR COMPRESSORS FOR A WIDE RANGE OF VEHICLE APPLICATIONS.
BENDIX®- AIR COMPRESSORS AIR COMPRESSOR FLANGES FLANGES REMANUFACTURED EXCHANGE COMPRESSORS ENGINES TU-FLO 500 TU-FLO 501 Caterpillar® 3406 285131X ---- 286546X 289349X Caterpillar® 3406B Caterpillar® 3408 284310X 103274X 286552X 103278X 289744X Mack® 6 Cylinder 284662X 289340X ---- 286544X 286620X* ---- Caterpillar 3116 ---- ---- ---- Mack® 8 Cylinder 277122X 286574X 102953X* Cummins® NH,NTC,KT,KTA Series Engines 284718X* 284699X TU-FLO 750 ---- ---104583X ---- ---107509X ---
BENDIX®- AIR COMPRESSORS IDENTIFICATION OF BENDIX® AIR COMPRESSORS IMPORTANT NOTICE Identification and porting references on BENDIX® air compressors are looking at the “non-drive” end of the compressor. The crankshaft should be facing away.
BENDIX®- AIR COMPRESSORS AIR COMPRESSOR IDENTIFICATION HOW TO “READ” AN AIR COMPRESSOR: 1. Determine the original manufacturer of the unit. a) Bendix® b) Midland® c) Cummins® d) Clayton Dewandre® e) other 2. Is the compressor a two or three piece design? a) Does it have a block and head? b) Does it have a block, head and a base? 3. Determine the type of mounting. a) 4 hole base b) 6 hole base c) Flange 4. If the compressor is flange mounted, determine the type of engine it is mounted on.
BENDIX®- AIR COMPRESSORS Air Compressor Kits: Compressor BX-2150 Model Number of Cylinders 1 108848 Field Maint. Kit 109356(CAT) TU-FLO 400 2 TU-FLO 500 2 TU-FLO 501 2 TU-FLO 550 2 TU-FLO 600 2 TU-FLO 700 2 TU-FLO 750 2 TU-FLO 1000 4 229416 229417 287043 NA 229417 289998 NA 229417 (2 req’d) Unloader Kit 108847 279614 279615 279615 107515 279615 279615 107515 279615 (2 req’d) Gasket Set NA 280511 280512 101558 NA 101559 101559 NA NA Cylinder Head Maint.
BENDIX®- AIR COMPRESSORS PLEASE NOTE: * Model: Tu-Flo 400 * Drive: Pulley * Cooling: Air * Type of Discharge: Flange * Mounting: 4 Hole Base * Notes: 227406X Pictured We offer a large number of additional (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information.
BENDIX®- AIR COMPRESSORS * Model: Tu-Flo 400 * Drive: Pulley * Cooling: Water * Type of Discharge: Flange * Mounting: 4 Hole Base * Notes: 289688X Pictured. Has base drain. Both 289687X and 289688X use bottom plates. PART NUM BER INLET PORT OUTLET PORT 101142X 289687X 289688X Le ft Right Le ft Le ft Right Le ft * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Drain.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount Tu-Flo 500/600 Tu-Flo 500/600 Pulley Water Flange/Threaded 4 Hole Base 227320X Pictured PART NUM BER M ODEL INLET PORT OUTLET PORT DISCHARGE BASE OIL OPTION 227320X 227321X 227322X 227323X 280604X 282076X 283690X 284020X TF500 TF500 TF500 TF500 TF600 TF500 TF500 TF500 Le ft Right Right Le ft Right Right Le ft Le ft Le ft Right Right Le ft Right Top Top Top Flange Flange Flange Flange Flang
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: PLEASE NOTE: Tu-Flo 500 Pulley Air Flange 4 Hole Base 228141X Pictured We offer a large number of additional (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Side/Slant Mount Tu-Flo 500 Tu-Flo 500 Pulley Water Threaded Slant Mount 229078X Pictured PART NUM BER INLET PORT OUTLET PORT 229078X 283513X Le ft Right Top Top * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Tu-Flo 501 Pulley Air(Block) / Water(Head) Flange / Threaded(#286557X) Side Mount 286557X Pictured PART NUM BER INLET PORT OUTLET PORT 286556X 286557X 286564X 286565X R
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount Tu-Flo 501 Tu-Flo 501 Pulley Air(Block) / Water(Head) Flange / Threaded(#286532X) 4 Hole Base Thru Drive, Base Oil Feed.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount Tu-Flo 501 Tu-Flo 501 Pulley Air(Block) / Water(Head) Flange/Threaded 6 Hole Base PART NUM BER INLET PORT OUTLET PORT DISCHARGE 102989X 286535X 286537X 286576X 286578X 286585X Right Right Le ft Right Le ft Le ft Right Right Top Right Le ft Le ft Flange Flange Thre ade d Flange Flange Flange * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: #286535X #286576X Pictured #28
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount Tu-Flo 700 Tu-Flo 700 Pulley Water Flange 6 Hole Base Rear and Base Oil Option.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: BX-2150 PLEASE NOTE: Air(Block) / Water(Head) Flange 104042X Pictured We offer a large number of additional (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 500/600 (Caterpillar® Application) Tu-Flo 500/600 Engine Water Flange Flange Tapered Shaft 284310X Pictured PART NUM BER A/C M ODEL INLET PORT OUTLET PORT 279995X 280556X 284310X TF500 TF600 TF500 Le ft Le ft Right Le ft Le ft Top * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 500 (Caterpillar® Application) Tu-Flo 500 Engine Water Flange
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Tu-Flo 501 PLEASE NOTE: Flange Mount Tu-Flo 501 We offer a large (Caterpillar® Application) Engine Air(Block) / Water(Head) number of additional Threaded Flange Spline Shaft, Rear Oil Inlet, Base Oil Drain. 286546X Pictured (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 750 (Caterpillar® Application) Tu-Flo 750 Engine Air(Block) / Water(Head) Optional Flange 109604X Pictured (has a spline shaft and 22 Tooth.) #107508X has a tapered shaft and 2 1/2° Tilt.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 500/600 (Cummins® Application) Tu-Flo 500/600 Engine Water Flange/Threaded Flange Long Case.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 550/750 (Cummins® Application) Tu-Flo 550/750 Engine Air(Block) / Water(Head) Optional Flange 107506X Pictured PART NUM BER A/C M ODEL INLET PORT OUTLET PORT 107506X 107507X TF550 TF750 Le ft Le ft Le ft/Top Le ft/Top * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 700 (Cummins® Application) Tu-Flo 700 Engine Water Optional Flange Standar
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Tu-Flo 400 Engine Water PLEASE NOTE: We offer a large number of additional (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 500/600 (Detroit Diesel® Application) Tu-Flo 500/600 Engine Water Threaded / Flange(#284106X) Flange 45° Tilt, 284106X Pictured PART NUM BER A/C M ODEL INLET PORT OUTLET PORT 281042X 282013X 284106X 285252X TF500 TF600 TF500 TF500 Le ft Le ft Le ft Right Top Top Le ft Top * Model: * Drive: * Cooling: * Type of Discharge: Flange Mount Tu-Flo 500/600 (Detroit Diesel® Application) Tu
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: PLEASE NOTE: Tu-Flo 501 Flange Mount Tu-Flo 501 We offer a large ® Engine number of additional (Detroit Diesel Application) Air(Block) / Water(Head) (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information. Threaded Flange 0° Tilt. Has press-on gear and Stud shaft.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Tu-Flo 700 Engine Water PLEASE NOTE: We offer a large number of additional (but not pictured) Air Compressors. Please call our friendly Customer Service Staff for more information.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Optional Flange 0° Tilt. #107623X is for 60Series, Thru-Drive.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: gines. Flange Mount Tu-Flo 500 (Mack® Application) Tu-Flo 500 Engine Water Flange Flange Mack® Foxhead for Mack® V8 en277122X Pictured PART NUM BER INLET PORT OUTLET PORT 277122X Le ft Le ft * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount Tu-Flo 500/600 (Mack® Application) Tu-Flo 500/600 Engine Water Flange / (#277901X has Threaded.) Flange Short Case.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: Flange Mount Tu-Flo 501 (Mack® Application) Tu-Flo 501 Engine Air(Block) / Water(Head) Threaded(#286621X) Flange(#286574X) * Mounting: Flange * Notes: Mack® Foxhead for Mack® V8 engines.
BENDIX®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Tu-Flo 700 Engine Water Flange Mount Tu-Flo 700 (Mack® Application) Optional Flange Mack® Foxhead for Mack® V8 engines. 289348X Pictured PART NUM BER INLET PORT OUTLET PORT 289348X Le ft Le ft/Top * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Tu-Flo 750 Engine Air(Block) / Water(Head) Optional Flange Mack® Foxhead for Mack® V8 engines.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER 104587X 104587X 104587X 104587X 104588X 106165X 108037X 103292X 106325X 289098X R-14 R-14 R-14 R-14 E-6 106000X 106005X 106010X 106016X 106019X 104588X 104588X 104588X 104588X 104588X 101186X 101563X 104349X 101304X 104331X E-6 E-6 E-6 E-6 E-6 104588X 104591X 104595X 104596X 104596X 104427X 287379X 104595X 103705X 104596X 104596X 104596X 104596X 104596X 104596X REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC. MODEL O.E NUMBER REMAN./ SERVICE DESC.
BENDIX®- AIR VALVES D-2 Governor * The D-2 governor operates in conjunction with the compressor unloading mechanism and controls system air pressure between a predetermined maximum and minimum pressure. * Adjustable piston type valve.
BENDIX®- AIR VALVES E-4 Dual Brake Valve * The E-4 dual brake valve is a graduating directional control valve and is generally used to control all the service brakes on a vehicle. * Floor Mounted. * Treadle or Lever actuated. * Used in dual circuit systems. 1/2” P.T. Delivery (2) 1/2” P.T. Supply Res. #1 NOTE: Pedal and Mounting Plate Not Furnished. PART NUM BER SUPPLY RES. #1 SUPPLY RES. #2 DELIVERY 279750X (1)-1/2" PT (1)-1/2" PT (2)-1/2" PT Exhaust 1/2” P.T. Supply Res.
BENDIX®- AIR VALVES E-7 Dual Brake Valve * The E-7 dual brake valve is a graduating, directional control valve. It is generally used to control the service brake of a vehicle. * It is used in dual or split air brake systems, and is actually two separate and independent valves in the housing operated by a single actuating mechanism. * Dual Circuit Foot Valve. * Floor mounted, treadle or lever operated. NOTE: Pedal and Mounting Plate Not Furnished. MAINTENANCE KIT: #289352 E J F K G L H 1/8”P.T.
BENDIX®- AIR VALVES * The E-10 dual brake valve is a graduating, directional control valve. It is primarily used on buses to control the service brakes. * Dual Circuit Foot Valve. * Floor Mounted, treadle operated. * Two separate supply and delivery circuits for primary and secondary braking. * Used in dual or split air brake systems. MAINTENANCE KIT: #102100 NOTE: Treadle and Mounting Plate Not Furnished. PART NUM BER SUPPLY DELIVERY E-10 Dual Brake Valve 3/8” P.T. Delivery-#2 (2) 3/8” P.T.
BENDIX®- AIR VALVES PP-1 / RD-3 Push-Pull Control Valve * The PP-1 push-pull control valve is a pressure sensitive, manually operable, on-off control which will automatically return to the exhaust position when manual force is removed and supply air pressure is below a required minimum. * Commonly used to control parking and emergency brakes. A Delivery (2) NOTE: Button and Mounting Nut Not Furnished.
BENDIX®- AIR VALVES ** The PP-5 push-pull control valve is a pressure sensitive, manually operated, on-off control which will automatically return to the exhaust position when manual force is removed and supply air pressure is below a required minimum. * Commonly used to control parking and emergency brakes. * Used in conjunction with vehicle torque converter systems, engine speed control systems and some parking brake systems. NOTE: Button and Mounting Nut Not Furnished.
BENDIX®- AIR VALVES * The MV-2 valve (Manifold) is an integrated control assembly designed for control panel mounting in a truck-tractor. * This non-metallic assembly consists of two push-pull valves and a dual circuit supply valve. NOTE: Buttons and Mounting Hardware Not Furnished.
BENDIX®- AIR VALVES * The TC-2 trailer control valve is a hand operated modulating control valve. * Steering Column Mount. * Generally used on tractors to provide modulated control on trailer brakes only. TC-2 Trailer Control Valve 1/4” P.T. Supply NOTE: Handle or Clamp Not Furnished. PART NUM BER 106133X 109764X 276270X 276272X 277765X GRADRANGE PSI 5-70 5-80 5-80 5-80 5-80 STEERING COLUM N DIAM ETER PSI PSI PSI PSI PSI Bottom View 1/4” P.T. 1/4” P.T.
BENDIX®- AIR VALVES TC-7 Trailer Control Valve * The TC-7 trailer control brake valve is mounted either on the exterior or interior of the steering column. * It is normally used to operate the trailer brakes independently of the tractor brakes. 1/4” P.T. Supply NOTE: The TC-7 is not designed for use as a parking brake control and should never be used to hold the brakes applied with vehicle unattended. NOTE: Handle and Mounting Bracket Not Furnished.
BENDIX®- AIR VALVES TW-3 Control Valve * The TW-3 control valves are manually operated, nonmodulating controls used extensively in the air brake system. * The TW-3 is used in parking and emergency brake systems and has slightly greater capacity than the TW-1. Vacuum Tube NOTE: Mounting Hardware Not Furnished. PART NUM BER VACUUM TUBE 225892X 283935X Ye s No 1/4” P.T. Delivery (2) 1/4” P.T.
BENDIX®- AIR VALVES QR-1 Quick Release Valve *The QR-1 is responsible for the rapid exhausting of air pressure, generally from brake chambers or spring brakes. * They decrease the brake release time due to their mounting location which is generally close to the brake chamber or spring brake they serve.
BENDIX®- AIR VALVES *The LQ-2 limiting, quick release valve serves two functions: that of a limiting valve and a quick release valve. * Generally used on the front or steering axle of a vehicle, it is controlled by a TW-1 two-way control valve mounted on the dash panel in the cab. * It will reduce front axle service applications by 50% when the TW1 control is placed in the “slippery road condition”. It will deliver full pressure when it is placed in the “dry road” position.
BENDIX®- AIR VALVES BP-1 Air Brake Proportioning Valve * The BP-1 brake proportioning valves are incorporated into the air systems to improve the controllability and reduce the stopping distance of bobtail operated tractors during braking. 3/8” P.T. Supply IMPORTANT NOTE: The BP-1 front & BP-1 rear valves are similar in appearance but are NOT interchangeable. 1/8” P.T.
BENDIX®- AIR VALVES * The SR-2 trailer spring brake valve is responsible for controlling the application and release of the spring brakes both during emergency situations and normal parking. * It is generally installed in the required spring brake release reservoir. * It protects and isolates the spring brake reservoir, preventing automatic brake application in the event of trailer service system failure. PART NUM BER A RES. CONN. B TRL. SERV.
BENDIX®- AIR VALVES SR-5 Trailer Spring Brake Valve * The SR-5 trailer spring brake valve is used on trailers with dual air brake systems. * The valve permits the use of a single reservoir on the trailer. PART NUM BER A M ALE PORT (RES. M TG) ANTICOM POUNDING 109615X 109616X 109617X 109618X 3/4" 3/4" 1/2" 1/2" Ye s No Ye s No 1/4” P.T. Service 1/4” P.T. Service/Spring Brake Reservoir 1/4” P.T. Trailer Supply A Male P.T. Res. Conn. 3/8” P.T. Delivery (4) 1/4” P.T.
BENDIX®- AIR VALVES * The R-8 relay valve is primarily used on long wheel base vehicles to apply and release rear axle(s) service or parking brakes. * The relay valve is used to balance the time of brake applications on heavy duty vehicles. * Piston operated. 1/4” P.T. Exhaust Cover MAINTENANCE KIT: #287370 Service PART NUM BER SERVICE PORT LOCATION (DEGREE) 286370X 286371X 287224X 287260X 288369X 90º 90º 270º 180º 180º R-8 Relay Valve 1/8” P.T. Balance Port (Located Under Exhaust Cover) 1/4” P.T.
BENDIX®- AIR VALVES R-14 Relay Valve (Vertical Delivery Ports) * The R-14 relay valve is primarily used on long wheel base vehicles to apply and release rear axle(s) service or parking brakes. * The relay valve is used to balance the time of brake applications on heavy duty vehicles. * Piston operated. * The unique anti-compounding feature, located above the service port, permits the R-14 to be used conveniently to control spring brakes as well as service brakes. Exhaust Cover 1/8” P.T.
BENDIX®- AIR VALVES R-7 Modulating Valve * The R-7 valve modulates the spring brakes through application of the foot brake valve in the event of loss of rear axle service brake pressure. * Commonly found on trucks and buses with dual air brake systems. NOTE: Spring brake release pressure is 95 PSI. 1/4” P.T. 3/8” P.T. Control Supply R-8P Pressure Equalizing Relay Valve * The R8-P pressure equalizing valve is a special purpose device designed specifically for use on semi-trailer converter dollies.
BENDIX®- AIR VALVES RE-4 Relay Emergency Valve * The RE-4 relay emergency valve is generally used on pre“121” trailers and in some special cases on off-the-road equipment. * It incorporates an emergency feature which will automatically apply the service brakes in the event that supply air pressure is lost. * Can be generally mounted either to the reservoir or remote from it. 1/4” P.T. Service 1/4” P.T. Emergency 3/4” P.T. Reservoir (2) PART NUM BER 1/4” P.T.
BENDIX®- AIR VALVES TP-2 Tractor Protection Valve * The TP-2 tractor protection valve is generally found mounted on the rear of the tractor cab. * It is used in conjunction with a dash mounted control valve. * It provides a means of opening and closing the two air hoses (service and emergency) leading to the trailer. * Automatically closes in the event of a tractor trailer breakaway or reduction of tractor system air pressure. 1/4” P.T. Control B Trailer Service 3/8” P.T.
BENDIX®- AIR VALVES * The TP-5 (Formerly the VM-2) valve is a panel or cross member mounted unit designed to replace the tractor protection valve. * It has two double check valves and a quick release valve. * It may be used in conjunction with the VM-3 or independently. TP-5 Tractor Protection Valve 1/2” P.T. Trl. Emergency Supply 3/8” P.T. Serv. Rear NOTE: Use #289253X when a trailer Control (Hand Valve) such as the TC-2 is not installed.
BENDIX®- AIR VALVES RV-1 Pressure Reducing Valve * The RV-1 pressure reducing valve is used where a constant set air pressure lower than supply air pressure is required. 1/4” P.T. Delivery PART NUM BER NOM INAL DELIVERY PRESSURE 101135X 277144X 277214X 278426X 85 PSI 80 PSI 75 PSI 65 PSI 9/32” Dia. Mtg. Holes 1/4” P.T. Supply * The PR-2 pressure protection valve is a normally closed, pressure control valve which can be referred to as a nonexhausting sequence valve.
BENDIX®- AIR VALVES * The SV-1 synchronizing valve is a pilot operated, nongraduating pneumatic control valve. * It is used to control air from a remote supply which is different than control air supply. They have definite opening and closing pressures and can be used to delay or sequence the action on other pneumatic devices. NOTE: With common control and supply pressure, Inlet and Exhaust opening p.s.i. are shown on chart below.
BENDIX®- AIR VALVES SC-1 Single Check Valve * The SC-1 single check valve is a protection device which separates and protects reservoirs located ahead of the arrow stamped on its body. * The valve permits air to flow through it in only one direction as indicated by the arrow. * This valve is commonly used to protect service brake air pressure.
BENDIX®- AIR VALVES * The TE-1 trailer emergency stop light switch is an electra-pneumatic switch. * It lights the trailer stop lights if pressure in the tractor emergency line is reduced to approximately 60 p.s.i. for any reason. TE-1 Trailer Emergency Stop Light Switch 8-32 Thrd. Terminal NOTE: Circuit between terminals to be closed from 60 p.s.i. to 0 PSI. 1/8” P.T. Air Supply PART NUM BER 228477X * The SL-3 stop light switch is an electra-pneumatic switch.
BENDIX®- AIR VALVES LP-3 Low Pressure Indicator * The LP-3 low pressure indicator is a pressure sensitive, electric-pneumatic switch that is designed to give an automatic warning to the vehicle operator in the event air pressure in the servie brake system is below a safe minimum for normal operating conditions. * Generally activates a dash mounted light and buzzer. A *NOTE: *#104246X has a push on terminal. *#275083X has a cut-in pressure of 75 +/- 6 PSI.
BENDIX®- AIR VALVES * The AD-2 air dryer is a desiccant type, inline filtration system that removes contaminants and provides dry air for the air brake system. AD-2 AIR DRYERS & CARTRIDGES AD-2 AIR DRYER CARTRIDGE AD-2 AIR DRYER Pipe Plug Outlet W/Integral Check Valve #101900X Inlet AD-2 AIR DRYER END COVER Inlet Either 12V or 24V Cast on Cover. Exhaust 1/4” P.T. Purge Line Port End Cover (Pictured to the right) Elec.
BENDIX®- AIR VALVES AD-4 AIR DRYERS & CARTRIDGES * The AD-4 air dryer is a desiccant type, inline filtration system that removes contaminants and provides dry air for the air brake system. AD-4 AIR DRYER CARTRIDGE AD-4 AIR DRYER #104358X AD-4 AIR DRYER END COVER Delivery Port w/Integral Check Valve 1/4” P.T. Purge Line Port Heater Thermo. Housing Exhaust Supply Safety Valve 1/4” P.T.
BENDIX®- AIR VALVES * The AD-9 air dryer is a desiccant type, inline filtration system that removes solid and vapor contaminants and provides dry air for the air brake system. AD-9 AIR DRYERS & CARTRIDGES (Please refer to page 157 for additional information.) AD-9 AIR DRYER CARTRIDGE AD-9 AIR DRYER Mounting Brackets #107695 #107794X AD-9 AIR DRYER END COVER Outlet With Check Assembly Outlet With Check Assembly Inlet Control Port AD-9 AIR DRYER PURGE VALVE Supply Port 1/4” P.T.
CUMMINS® / HOLSET®- AIR COMPRESSORS Crossover Information: 3018527X CROSSOVER NUMBERS AR7944 AR8311 AR8312 AR13134 AR13140 AR13141 AR45603 AR51688 3005840 3010879 3015034 3016082 3018543X CROSSOVER NUMBERS 3018527 3018530 3018531 3018541 3018542 SEE PAGE 155 FOR ADDITIONAL CUMMINS® / HOLSET® INFORMATION QE TYPE AR13135 AR13136 AR13139 AR40220 AR45211 3015630 AR8371 AR10650 AR11952 AR13142 AR13150 AR13160 3018534 3018543 3018544 L-10 & M-11 2.
CUMMINS® / HOLSET®- AIR COMPRESSORS * Model: Single Cylinder * Drive: Engine * Cooling: Water * Type of Discharge: Threaded * Mounting: Flange * Notes: For remote mount governor application.
CUMMINS® / HOLSET®- AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Cummins® / Holset® Flange Mount Single Cylinder Gear Water * For More Holset ® Information turn to Page 155 Threaded Flange PART NUM BER 3558006X * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Twin Cylinder Gear Water Cummins® / Holset® Flange Mount Threaded Flange PART NUM BER 3048680X * The Cummins® fuel solenoid is an electric shut-down valveand is held open while
FULLER® - VALVES * The Fuller® valve is used in conjunction with the shift block to shift the transmission of a vehicle from high to low range and vice-versa. * OLD STYLE 7, 8, 9, 10 Speed. FULLER® Push Pull Valve PART NUM BER A3546X * The Fuller® shift block is used to shift the transmission of a vehicle from high to low range and vice-versa. FULLER® Shift Block PART NUM BER A4688X * The Eaton®/Fuller® shift block is used to shift the transmission of a vehicle from high to low range and vice-versa.
FULLER® - VALVES * Available in NEW ONLY. * The transmission range valve features a “ruberized” shift knob cover for driver comfort. * 1/16” NPT for all ports. * Includes upper and lower covers. * 13 Speed - Direct & Overdrive. Fuller® Style Transmission Range Valve “Red” Splitter Knob PART NUM BER A4900 A6913 * Available in NEW ONLY. * The transmission range valve features a “ruberized” shift knob cover for driver comfort. * 1/16” NPT for all ports. * Includes upper and lower covers.
FULLER® - VALVES Fuller® Style Transmission Air Regulator * Available in NEW ONLY. * I/4” NPT Inlet. * 1/8” NPT Outlet * Non-Adjustable Preset PSI at factory (58 to 62 PSI) PART NUM BER 16743 * Available in NEW ONLY. * The transmission delector valve features a chrome plated cover. * 1/16” NPT for all ports. * This valve has a three (3) position selector. Fuller® Style Transmission Selector Valves Selector Selector OD DIR LO OLD STYLE 13 Speed (Does not use an A 3546X.
MIDLAND® - AIR COMPRESSORS MIDLAND® AIR COMPRESSOR CROSSOVER O.E.M. NUMBER OUR REMAN NUMBER O.E.M.
MIDLAND® - AIR COMPRESSORS IMPORTANT NOTICE Identification and porting references on MIDLAND® air compressors are looking at the “drive” end of the compressor. The crankshaft should be facing towards you.
MIDLAND® - AIR COMPRESSORS Air Compressor Kits Compressor Model Number of Cylinders Gasket and Seal Kit (Flange Mount) EL740 EL850 2 1 EL1300 EL1600 2 2 RN26HA (Caterpillar ) RN26GX (Cummins ) RN26GY (Detroit ) RN26GZ (Mack ) RN26HA (Caterpillar ) RN26GX (Cummins ) RN26GY (Detroit ) RN26GZ (Mack ) ® RN26GT RN26JH ® ® ® Gasket and Seal Kit (Base Mount) ® ® ® ® RN26GV RN26JG RN26GW RN26GW Standard RN26ER RNT26JE RN26ED RN26ED .
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL740 EL740 Pulley/Belt Air Threaded 4-Hole Base End cap oil feed only. KN7000X Pictured PART NUM BER INLET PORT OUTLET PORT KN7000X Right Le ft * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL740 EL740 Pulley/Belt Air Flange 4-Hole Base Base oil option.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL740 EL740 Pulley/Belt Air(Block) / Water(Head) Flange 4-Hole Base Non-Rotatable Head. KN7040X Pictured PART NUM BER INLET PORT OUTLET PORT KN7040X KN7050X Right Le ft Right Le ft * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL740 EL740 Pulley/Belt Air(Block) / Water(Head) Flange 4-Hole Base Special bottom plate for Ford®.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL850 EL850 Belt/Pulley Air Threaded 4-Hole Base End Cap Oil Feed. Base Oil Drain. KN85020X Pictured PART NUM BER INLET PORT OUTLET PORT KN85020X Right Top * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL850 EL850 Belt/Pulley Air(Block) / Water(Head) Threaded 4-Hole Base End Cap Oil Feed. Base Oil Drain.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Base Mount EL1600 EL1600 Pulley Water Top/Flange 4-Hole Base KN16060 has base oil feed. KN16020X Pictured PART NUM BER ROTATION HEAD ROTATION BLOCK KN16020X KN16060X Right Right Right Right * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount EL1300 (Caterpillar® Application) EL1300 Engine Water Top/Flange Flange KN13081X block is rotated 180°. End cap oil feed.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Shaft: * Notes: Flange Mount EL1600 (Caterpillar® Application) EL1600 Engine Water Top/Flange Flange Tapered shaft KN16200X has threaded mounting holes.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: Flange Mount EL850 (Cummins® Application) EL850 Engine Air (KNT85230X) Water (KNT86230X) * Type of Discharge: Threaded * Mounting: * Notes: For Cummins® B-Series Engines. Flange mount, gear drive. Bottom oil drain.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount EL1300 (Detroit Diesel® Application) EL1300 Engine Water Top/Flange Flange Flange mount, gear drive. End cap oil feed. Oil drain internal at flange. KN13051X is for 60-Series, NonThru-Drive.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount EL1600 (Detroit Diesel® Application) EL1600 Engine Water Top/Flange Flange Flange mount, gear drive. End cap oil feed. Oil drain internal at flange. KN16051X is for 60-Series, NonThru-Drive.
MIDLAND® - AIR COMPRESSORS * Model: * Drive: * Cooling: * Type of Discharge: * Mounting: * Notes: Flange Mount EL1300/1600 (Mack® Application) EL1300/1600 Engine Water Top/Flange Flange Flange mount, gear drive. Crankshaft end oil feed. Flange oil drain. #13111/16111X are for power steering.
MIDLAND® - AIR VALVES MIDLAND® AIR VALVE CROSSOVER O.E.M. NUMBER OUR REMAN NUMBER O.E.M. NUMBER OUR REMAN NUMBER O.E.M.
MIDLAND® - AIR VALVES MIDLAND® Air Governor * The governor operates in conjunction with the compressor unloading mechanism and controls system air pressure between a predetermined maximum and minimum pressure. * This particular governor is a diaphragm-type. 1/8” NPTF Reservoir NOTE: 1/16” unloader ports are for direct compressor mounting. The 1/8” unloader ports are for remote governor mounting.
MIDLAND® - AIR VALVES * This valve is a single circuit foot valve. * It is used primarily on pre-FMVSS-121 vehicles. * The valve is a foot operated service brake control. * All supply and delivery ports are common. MIDLAND® Single Circuit Foot Valve 1/2” P.T. Delivery (4) NOTE: Studs Not Furnished. PART NUM BER 1/4” P.T. Supply (2) Exhaust KN22100X (Located underneath) * This valve is a dual circuit foot valve in which there are two separated, individual service brake circuits in a single housing.
MIDLAND® - AIR VALVES * This hand operated flipper-style valve is generally used for manual control of front wheel brake limiting and for interaxle differential lock-out control. * It is usually for panel mounting. * It is an on-off, non-automatic two position valve. MIDLAND® Hand Operated Valve (Flipper Style) 1/8-27 NPTF Delivery (2) PART NUM BER 1/8” NPTF Supply KN20000X * These valves are automatic valves that “pop-out” and exhaust at 20-45 PSI.
MIDLAND® - AIR VALVES * The hand operated, flipper-style valve offers manual twoposition control with a cable attached. * Opposite cam rotations deliver pressure in opposite handle positions. MIDLAND® Hand Operated Valve (Flipper Style) NOTE: Cable Not Furnished. #KN20050X is a reverse cam valve. 1/8-27 NPTF Delivery (2) PART NUM BER KN20040X KN20050X 1/8-27 NPTF Supply * The push-pull, hand operated valve is a dead man type. * It applies pressure only when manually held in.
MIDLAND® - AIR VALVES * The manifold dash module is an integrated control assembly designed for control panel mounting in a truck-tractor. * This non-metallic assembly consists of two push-pull valves and a dual circuit supply valve. MIDLAND® Manifold Dash Module Exhaust Tractor Delivery Aux. Supply NOTE: Knobs and Mounting Hardware Not Furnished. Dash View Rear View PART NUM BER Trailer Delivery KN20615X Reservoir 1 * The Berg® hand control valve is a push-pull type valve.
MIDLAND® - AIR VALVES * The trailer service brake control valve is a hand operated modulating control valve. * It is also called a trailer control hand valve. * Generally used on tractors to provide modulated control on trailer brakes only. * Base unit for In-Column mount. MIDLAND® Trailer Service Brake Control Valve NOTE: Knob and Handle Not Furnished. PART NUM BER 1/4-18 NPTF Delivery (1) KN20540X KN20541X * The trailer service brake control valve is a hand operated modulating control valve.
MIDLAND® - AIR VALVES *The quick release valve is responsible for the rapid exhausting of air pressure, generally from brake chambers or spring brakes. * They decrease the brake release time due to their mounting location which is generally close to the brake chamber or spring brake they serve. MIDLAND® Quick Release Valve Supply Delivery (2) NOTE: The KN32020X has a die cast bottom cover and has high pressure differential compared to the low pressure differential in the KN32000X and KN32010X.
MIDLAND® - AIR VALVES MIDLAND® Front Axle Limiting Valve * The front axle limting valve is for use in front axle brake systems. * This valve automatically reduces output to 50% of input when input is 40 psi or less. * It delivers full output when input is 60 psi or more.
MIDLAND® - AIR VALVES MIDLAND® Relay Valve * The relay valve is used to apply and release service brakes on the tractor or the trailer. * It also functions to speed the application and release of airoperated brakes. * It has 2 ports for delivery. 3/8” P.T. Control NOTE: The KN28060X has a low pressure differential. PART NUM BER DELIVERY CRACK PRESSURE KN28060X KN28061X KN28132X (2)-3/8" PT (2)-1/2" PT (2)-1/2" PT 4.6+/- 1.5 PSI 4.6+/- 1.5 PSI 7.0+/- 1.5 PSI 1/2” P.T.
MIDLAND® - AIR VALVES MIDLAND® Relay Valve * The relay valve is used to apply and release service brakes on the tractor or the trailer. * It also functions to speed the application and release of airoperated brakes. * It has 4 ports for delivery. 3/8” P.T. Control NOTE: KN28080X has a 7 PSI crack pressure. KN28085X has a 4 PSI crack pressure. 1/2” P.T. Reservoir (2) PART NUM BER 3/8” P.T.
MIDLAND® - AIR VALVES * The RF relay valve is used to apply and release service brakes on tractor or trailer. * It has a low differential - high capacity. * Meets or exceeds FMVSS-121 requirements. * The auxiliary port on A103600X may be used for air suspensions or other accessories requiring reservoir air. * These valves have 4 ports for delivery. * The crack pressure is 4.5 +/- 1 PSI. Midland® RF Relay Valve Bottom View 1/4” P.T. Control NOTE: Mounting Brackets Not Furnished.
MIDLAND® - AIR VALVES * The RS-2 tandem modulator valve provides both normal braking control and skid control operation as required by FMVSS-121 for both axles of a tandem trailer brake system. * Importantly, this valve provides for normal service braking operation of either axle should a service system failure of the other axle occur. * It has four ports for delivery. Midland® RS-2 Tandem Modulator Valve 1/4-18 NPTF Control/ Service Solenoid/Elec. Connection 3/8” P.T.
MIDLAND® - AIR VALVES MIDLAND® FAB Valve (Fast Air & Balancing Relay Valve) * The FAB valve is used on converter dollies and long wheel base towing tractors to speed the tractor control signal to the rear trailer(s) service brakes. * It is also called a speed-up or fast air relay. * This valve has two ports for delivery. * The crack pressure is 0 PSI. * The differential is 0 PSI. 3/8” P.T. Control PART NUM BER 1/2” P.T.
MIDLAND® - AIR VALVES Midland® Relay Valve * The relay valve is primarily used on long wheel base vehicles to apply and release rear axle(s) service or parking brakes. * The relay valve is used to balance the time of brake applications on heavy duty vehicles. PART NUM BER 12345X * The multi-function valve is generally used on pre-”121” trailers and in some special cases on off-the-road equipment.
MIDLAND® - AIR VALVES Midland® RT Trailer Spring Brake Valve * The RT trailer spring brake valves are used on trailers to control both parking and emergency brake functions. * This valve controls reservoir charging. * It also meets FMVSS-121 requirements. * Importantly, the valve applies the emergency (parking) brakes upon loss of trailer supply (emergency) line pressure. 1/2” P.T. Trailer Service/ Control C Trailer Supply/ Emergency With AntiCompounding PART NUM BER A88802X A88812X 1/2” P.T.
MIDLAND® - AIR VALVES * The FF-2 full function valve is designed to fill your trailer MIDLAND® system reservoir while simultaneously filling the spring brakes 3/8” NPFT (thereby releasing your parking brakes) to assure you have Supply service brake capability when you are ready to drive the (Located on opposite side of vehicle away. control port) * It can be used with single or twin air tanks.
MIDLAND® - AIR VALVES MIDLAND® Tractor Protection Valve * The Midland® tractor protection valve protects the tractor air brake system under trailer breakaway conditions and when major leakage has occurred in the tractor or trailer. * It is also used to shut off trailer service and supply lines before disconnecting the tractor from the trailer. * This valve is a two-line, non-automatic style valve. * It has a built-in quick release. 3/8” P.T. Tractor Service 1/2” P.T.
MIDLAND® - AIR VALVES MIDLAND® One-Way Check Valve * The one-way check valve is used wherever pressures must be isolated and not allowed to back feed. * A popular use is to protect dry tanks from wet tank failure, pre FMVSS-121. * This check valve can be used on truck, tractors and trailers.
MIDLAND® - AIR VALVES We Also Offer New and Remanufactured Springbrakes and Components *The Midland® drain valve ejects moisture and contaminents from the air system reservoir upon a slight reduction in reservoir pressure. * Mounts to bottom drain port of the reservoir. PART NUM BER NOTES KN24000X KN24001X Automatic, Non-He ate d Automatic, He ate d MIDLAND® Drain Valve 3/8” P.T 3/8” P.T * The Midland® pressure protection valve is used to protect the air brake system from accessory failure.
MIDLAND® - AIR VALVES * The Midland® air regulating valve is used in air systems where reduced levels are required. * It is for auxiliary systems only. * Pressure settings are based on 100 PSI supply. * It is designed for constant supply not on-off applications. * A popular use is with air cylinders on bus door operators. PART NUM BER PRESSURE SETTING KN31050X KN31060X 45 PSI 65 PSI * The Midland® air regulating valve is used wherever a reduced pressure is required.
SEALCO® - AIR VALVES * The relay emergency valve is generally used on pre- “121” trailers and in some special cases it is used for off-the-road equipment. * Incorporates an emergency feature which will automatically apply the service brakes in the event that supply air pressure is lost. Relay Emergency Valve 1/4” P.T. Control 1/4” P.T. Control REPAIR KIT: #10005AX (Pictured) PART NUM BER A1000SX 1/2” P.T. Reservoir 1/4” P.T. Delivery (4) CRACK PRESSURE 1/4” P.T. Emergency Supply #10005AX Cartridge 1.
SEALCO® - AIR VALVES * The relay emergency valve is generally used on pre- “121” trailers and in some special cases it is used for off-the-road equipment. * Incorporates an emergency feature which will automatically apply the service brakes in the event that supply air pressure is lost. * Commonly used on converter dollies, turntable axles and air lift axles with service brake chambers. PART NUM BER 110338X CRACK PRESSURE NON-CHARGING Relay Emergency Valve 3/8” P.T. Emergency Supply 3/8” P.T. Serv.
SEALCO® - AIR VALVES Mini-Valve * The mini-valve is an early version control line valve used primarily on dollies. Improves application and release of brakes on dollies and rearmost trailer axles in double and triple trailer combinations. 3/8” P.T. Reservoir (Located underneath). 1/4” P.T. Control (2) PART NUM BER 3100X CRACK PRESSURE 1/4” P.T. Delivery (Another port located on opposite side). 2.
SEALCO® - AIR VALVES Control Line Valve * The control line valve is primarily used on dollies and turntable axles on pull, transfer and train type trailers. * Some benefits include: 1) A balanced control line signal for uniform braking of multi-axle combination vehicles. 2) Prevents premature braking of the steerable axle(s) in combination vehicles for maximum lateral stability while stopping.
SEALCO® - AIR VALVES Service Relay Valve 2-Port Delivery * The service relay valves are used primarily for single axle trailer service brakes or axle by axle trailer brake designs. * Generally for nipple mounting. 3/8” P.T. Control NOTE: Bracket or Mounting Hardware Not Furnished. #110360X also called a LOV-2. PART NUM BER CRACK PRESSURE 110360X 110410X 1.5 PSI 4.0 PSI * The service relay valves are used primarily for tandem axle trailer service brakes with four (4) brake chambers.
SEALCO® - AIR VALVES 3/8” P.T. Supply 3/8” P.T. Control (A/C) Spring Brake Control Valve Protected Reservoir System Reservoir A Reservoir B 3/8” P.T. Delivery (4) * The spring brake control valve is generally responsible for controlling the application and release of the spring brakes both during emergency situations and normal parking. * It protects and isolates the spring brake reservoir, preventing automatic brake application in the event of trailer service system failure.
SEALCO® - AIR VALVES * The tractor protection valve is generally found mounted on the rear of the tractor cab. * It is used in conjunction with a dash mounted control valve. * It provides a means of opening and closing the two air hoses (service and emergency) leading to the trailer. * Automatically closes in the event of a tractor trailer breakaway or reduction of tractor system air pressure. Breakaway Valve/ Tractor Protection Valve 1/2” P.T. Control Out 1/4” P.T. Control In 1/4” P.T.
SEALCO® - AIR VALVES Quick Release Valve *The quick release valve is responsible for the rapid exhausting of air pressure, generally from brake chambers or spring brakes. * This valve decreases the brake release time due to their mounting location which is generally close to the brake chamber or spring brake they serve.
SEALCO® - AIR VALVES Foot Valve Single Circuit * The single circuit foot valve is a graduating directional control valve and is generally used to control all the service brakes on a vehicle. * Floor Mounted. * Treadle or Lever actuated. * Used in single circuit systems. 1/2” P.T. Delivery Out (4) NOTE: Treadle Assembly and Mounting Plate Not Furnished. PART NUM BER 6125X 1/2” P.T.
SEALCO® - AIR VALVES Lever Control Valve * The lever control valves are manually operated, nonmodulating controls used extensively in the air brake system. NOTE: Mounting Plate Not Furnished. 1/8” P.T. Outlet 1/8” P.T. Outlet PART NUM BER 1/8” P.T.
SEALCO® - AIR VALVES * The pull-push hand control valve is a pressure sensitive, manually operable, on-off control which will automatically return to the exhaust position when manual force is removed and supply air pressure is below a required minimum. * Commonly used to control parking and emergency brakes. NOTE: Button and Name Plate Not Furnished. PART NUM BER 99600-2X SHUT-OFF PSI Hand Control Valve Pull-Push w/Automatic Shut-Off #10-24 Thrd. (2) 1/4” P.T. Outlet 1/8” P.T. Exhaust 1/4” P.T.
SEALCO® - AIR VALVES Air Starter Valve * Air Starter Valve Note: #11900X and #14900X have mounting holes. #10900X has the auxiliary port closed. 1/4” P.T. Appl. Port Outlet PART NUM BER INLET PORT 10900X 11900X 14900X (1)-1 1/2" PT (1)-1 1/2" PT (1)-1 1/4" PT OUTLET PORT Inlet Auxiliary (Closed on #10900X) (1)-1 1/2" PT (1)-1 1/2" PT (1)-1 1/4" PT Air Starter Valve * Air Starter Valve 1/4” P.T. Appl. Port 1/4” P.T. Appl. Port PART NUM BER 1” P.T.
WILLIAMS ®- AIR VALVES NOTE: We offer a complete line of NEW and REMANUFACTURED WILLIAMS CONTROLS, Inc. products. Please refer to your price sheet or call for the items that are not pictured in this section of the catalog. WM-90 Series 3-Way Regulating Valves * Available in NEW and REMANUFACTURED. * The WM-90 three-way valves are general purpose pushrod actuated regulators. * They are used as subassemblies in many other Williams products. * They are available in a variety of output ranges.
WILLIAMS ® - AIR VALVES * The WM-219C4 consists of a two position, three-way toggle valve. * It includes a heavy duty metal control lever. * It is designed for panel mounting. * Commonly used to control air pressure-operated relay valves, cylinders, PTO’s and fifth wheels.
WILLIAMS ®- AIR VALVES * The WM-388U1C1D is a general purpose throttle cylinder. * It features levers with multiple holes for easy connection to a variety of throttle linkages. WM-388 Series Air Throttle Cylinder .25 Dia. Holes (6) 1/4-18 NPTF Control NEW PART NUM BER 117888 WM NUM BER PRESSURE RANGE WM -388U1C1DX .27 Dia. Mounting Holes (2) 0-30/35 PSI * The WM-397J control valve is a manually operated, threeway pneumatic valve that is actuated by a push button.
WILLIAMS ® - AIR VALVES *Available in NEW ONLY. * The WM-459L regulator panel is a complete pre-plumbed unit designed for easy installation in industrial and vehicular applications. * Each panel is comprised of an illuminated gauge, a WM219C3 toggle valve and a self-releiving, knob-actuated WM279 series pressure regulator.
WILLIAMS ®- AIR VALVES WM-606 Series Column-Mounted Regulating Valve * The WM-606C2C is a three-way regulating valve designed for column mounting. * It is commonly used to provide hand control of vehicular spring brakes. NOTE: Gage is Not Furnished. WM NUM BER OUTPUT RANGE M AXIM UM OUTPUT WM -6 0 6 C2 CX 0 -1 2 0 PS I Ta nk NEW PART NUM BER 11 3 7 3 0 1/4-18 NPTF Control *The WM674A is a dual function valve used to control spring brakes under normal and emergency conditions.
WILLIAMS ® - AIR VALVES * The WM783A is composed of a non-compensating four-way control valve with three functional positions. * The WM783A models are equipped with a spring-loaded lockout safety device which locks the control lever in each of the three positions to prevent unintentional movement. NEW PART NUM BER WM NUM BER 118317 WM -783AX * The WM784A is composed of a non-compensating, fourway control valve with three functional positions.
MISCELLANEOUS - VALVES SLOAN® Valve MIDLAND® Style Leveling Valve * The Sloan® valve is a tractor trailer park valve with a two-way check valve. * The two-way check valve allows either primary or secondary air supply to operate spring brakes on tractor and/or trailer combinations. Available in New Only. PART NUM BER PART NUM BER Model Number stamped on bottom 1070M KX * The Neway® leveling valve is a height control valve that is used to control the air pressure in the air springs for varying loads.
MISCELLANEOUS - VALVES * Available in NEW ONLY. Rockwell®/WABCO® Style Air Dryer Cartridge PART NUM BER R950011 * Clayton Dewandre® governor.
MV-3 STYLE CONTROL MODULE (New) (Information continued from page 72.) To Replace Part # 065156 ... 065186 ... 065208 ... 065248 ... 065305 ... 106981 ... 107215 ... 107218 ... 107220 ... 107753 ... 131061 ... 131062 ... 800036 ... 800039 ... 800145 ... 800259 ... 800260 ... 800353 ... 800515 ... 800519 ... 800522 ... 800523 ... 800525 ... 800528 ... 800530 ... 5000286 .. 5000378 .. 5000379 .. 5000428 .. 5000429 .. 5001302 .. 5002197 .. 5002205 .. 5002714 .. 5002716 .. 5002737 .. 5002738 .. 5003585 ..
CUMMINS® & HOLSET® Air Compressors PART NUMBER PART NUMBER DESCRIPTION DESCRIPTION 3558022X 3558027X 3558042X 3558043X 3558044X AIR COMPRESSOR CUMMINS / HOLSET, 2 CLY. CUMMINS AIR COMPRESSOR CUMMINS AIR COMPRESSOR CUMMINS AIR COMPRESSOR 3558144X 3558151X 3558153X 3558159X 3558167X CUMMINS QE AIR COMP. QE AIR COMPRESSOR CUMMINS QE 1 CYL. AIR COMP. CUMMINS AIR COMPRESSOR QE AIR COMPRESSOR 3558045X 3558049X 3558013X 3558050X 3558051X CUMMINS 1 CYL. AIR COMP. CUMMINS QE AIR COMP.
NEW VALVES & PRODUCTS BENDIX® Style Valves & Components NEW PART NUMBER DESCRIPTION Note: Bendix® Style Components & Products 065145 065146 065157 065224 065225 BPR-1 VALVE BPR-1 VALVE MV-3 VALVE AD- 9 AIR DRYER AD-9 AIR DRYER 065437 065476 065643 065661 065706 SR-4 TRAILER VALVE R12P PILOT RELAY VLV PP-DC DASH VALVE PP-DC CONTROL VALVE TP3-DC TRAC PROT VLV 1 0 111 2 101437 101557 101622 101786 SR-4 TRAILER VALVE MV-2 DASH CONT VLV MV-2 CHECK ASSEMBLY SR-4 TRAILER VALVE TC-6 BRAKE VALVE 101818 10202
NEW VALVES & PRODUCTS BENDIX® Style Valves & Components Cont.
NEW VALVES & PRODUCTS CUMMINS® Style MIDLAND® Style NEW PART NUMBER DESCRIPTION Cummins ® Style NEW PART NUMBER DESCRIPTION Midland ® Style 6997312 6997324 12V FUEL SOLENOID 24V FUEL SOLENOID 13241 LOW AIR SWITCH 13250 13255 12352 K N1 8 5 3 7 K N2 0 0 0 1 SERV STOP/L SWIT TRL EME STOP/L SW RELAY EMERG VALVE GOVERNOR DASH VALVE K N2 0 0 3 1 K N2 0 0 3 3 K N 2 0 11 0 K N2 0 5 4 1 K N2 0 5 5 1 DASH VALVE DASH VALVE DASH VALVE HAND CONT VALVE HAND CONT VALVE K N2 0 5 5 2 K N2 0 5 6 1 K N2 0 5 8 0
NEW VALVES & PRODUCTS NOTES N OTES DESCRIPTION NEWAY® Style N E W PA R T N U MB E R D E S C R IP T ION N e w a y ® S t y le 90044162 90054007 90054074 90054075 90054079 S HOC K A B S ORB E R LE V E LING VA LV E E LE C S OLE NOID VA LV E E LE C S OLE NOID VA LV E P ILOT VA LV E SEALCO® Style Cont.
AIR DRYERS, CARTRIDGES & KITS NEW PART NUMBER 109484 109495 5003547 DESCRIPTION AD-IP Style Del Chk Valve Kit AD-IP Style Heater & Thermostat AD-IP Style Purge Kit PART # Part Number AD-IP Descriptions 109477X 5000709X AD-IP Air Dryer AD-IP Drop In Air Dryer 109493X AD-IP Cartridge NOTES 5000709X Pictured NEW PART NUMBER 109993 109995 5008414 DESCRIPTION AD-SP Style Turbo Cutoff Kit AD-SP Style Purge Valve Kit AD-SP Style Cartridge Kit PAR T # Part Number AD-SP Descriptions 109991X 109992X 80
AIR DRYERS, CARTRIDGES & KITS NEW PART NUMBER DESCRIPTION 287053 AD-2 Style Purge Valve Maint. Kit PART # NOTES NEW PART NUMBER DESCRIPTION 104358 103818 103879 103980 AD-4 Style Cartridge AD-4 Style Purge Valve Maint.
QUALITY REMANUFACTURED CALIPERS 3.38” BENDIX SINGLE PISTON APPLICATION 55098X RH (Pictured) 55099X LH 55199X RH (Pictured) 55200X LH NAVISTAR NAVISTAR GMC/CHEVROLET GMS/CHEVROLET 2.60” BENDIX TWIN PISTON 55245X 1ST DESIGN (Pictured) NAVISTAR 55314X 2ND DESIGN (Pictured) NAVISTAR 2.88” BENDIX TWIN PISTONS 55250X NAVISTAR/GMC/CHEV (Pictured) 2.50” DAYTON WALTHER TWIN PISTON 55251X FORD/GMC/CHEV (Pictured) 2.88” DAYTON WALTHER TWIN PISTON 55252X FORD/GMC/CHEV (Pictured) 2.
LUCAS SYSTEM PARK CYLINDER ASSEMBLY 201179X 1 3/4” LH 201180X 1 3/4” RH (Pictured) ADJUSTER CYLINDER ASSEMBLY 201183X 1 3/4” LH (Pictured) 201184X 1 3/4” RH 5” SHOES BACKING PLATE ASSEMBLY 6 & 7” SHOES 203262X 1 3/4” LH (Pictured) 203261X 1 3/4” RH 203252X 1 3/4” LH 203251X 1 3/4” RH (Pictured) MAXI BRAKE H SERIES KSH101AX * (Pictured) KSH202CX ** *Two bleeder ports and one large port ** One large port VALVES 065147X HR-1 (Pictured) 065316X TW-11 065356X TW-11 QUALITY HEAVY DUTY PARTS Page 16
FAN CLUTCHES HORTON® 590009X 591001X 790007X 791009X BENDIX® 106970X 591024X 791019X KYSOR® 104750X 68501X HORTON® BENDIX® & KYSOR® FAN CLUTCHES ARE AVAILABLE.
