Product Manual
66
INTRODUCTION
1. Read and understand all instructions and all safety
warnings before operating lift.
2. Care must be taken as burns can occur from touching
hot parts.
3. Do not operate equipment with a damaged cord or if the
equipment has been dropped or damaged until it has been
examined by a qualied service person.
4. Do not let a cord hang over the edge of the table, bench,
or counter or come in contact with hot manifolds or moving
fan blades.
5. If an extension cord is necessary, a cord with a current
rating equal to or more than that of the equipment should be
used. Cords rated for less current than the equipment may
overheat. Care should be taken to arrange the cord so that it
will not be tripped over or pulled.
6. Always unplug equipment from electrical outlet when not
in use. Never use the cord to pull the plug from the outlet.
Grasp plug and pull to disconnect.
7. Let equipment cool completely before putting away. Loop
cord loosely around equipment when storing.
8. To reduce the risk of re, do not operate equipment in the
vicinity of open containers of ammable liquids (gasoline).
9. Adequate ventilation should be provided when working
on operating internal combustion engines.
10. Keep hair, loose clothing, ngers, and all parts of body
away from moving parts. Keep feet clear of lift when lowering.
Avoid pinch points.
11. DANGER! To reduce the risk of
electric shock, do not use on wet surfaces
or expose to rain. The power unit used on
this lift contains high voltage. Disconnect
power at the receptacle or at the circuit
breaker switch before performing any elec-
trical repairs. Secure plug so that it cannot
be accidentally plugged in during service, or
mark circuit breaker switch so that it cannot
be accidentally switched on during service.
12. Use only as described in this manual.
Use only manufacturer’s recommended attachments.
13. ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses only have impact resistant lenses, they are not
safety glasses.
14. Consider work environment. Keep work area clean.
Cluttered work areas invite injuries. Keep areas well lit.
15. Guard against electric shock. This lift must be grounded
while in use to protect operator from electric shock. Never
connect the green power cord wire to a live terminal. This is
for ground only.
16. Only trained operators should operate this lift. All
non-trained personnel should be kept away from the work
area. Never let non-trained personnel come in contact with,
or operate lift.
17. DO NOT override self-closing lift controls.
18. Clear area if vehicle is in danger of falling.
19. ALWAYS make sure the safeties are engaged before
attempting to work on or near a vehicle.
21. WARNING! RISK OF EXPLOSION. This
equipment has internal arcing or sparking
parts which should not be exposed to am-
mable vapors. This machine should not be
located in a recessed area or below oor
level.
22. MAINTAIN WITH CARE. Keep lift clean for better and
safer performance. Follow manual for proper lubrication and
maintenance instructions. Keep control handles and/or
buttons dry, clean and free from grease and oil.
23. Check for damaged parts. Check for alignment of
moving parts, breakage of parts or any condition that may
affect operation of lift. Do not use lift if any component is
broken or damaged.
24. NEVER remove safety related components from the lift.
Do not use lift if safety related components are missing or
damaged.
23. STAY ALERT. Use common sense and watch what you
are doing. Remember, SAFETY FIRST.
SAVE THESE INSTRUCTIONS
1. Carefully remove the crating and packing
materials. CAUTION! Be careful when cutting steel
banding material as items may become loose and fall
causing personal harm or injury.
2. Check the voltage, phase and proper amperage
requirements for the motor shown on the motor plate.
Wiring should be performed by a certied electrician only.
IMPORTANT SAFETY INSTRUCTIONS
Read these safety instructions entirely
IMPORTANT NOTICE
Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures.
Never attempt to lift components without proper lifting tools such as forklift or cranes.
Stay clear of any moving parts that can fall and cause injury.