Product: TDP-60-HN / 1.3.1999 SERVICE MANUAL BENEFON SPICA TDP-60-HN Dp_60ngbTOC.
Product: TDP-60-HN / 1.3.1999 TDP-60-HN 1.0 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 1.1 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . 1 - 1 1.1.1 Operational System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 1.1.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 1.1.3 Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 1.1.
Product: TDP-60-HN / 1.3.1999 3.3.3 HF-function tuning in practice . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 13 4.0 SERVICE APPLICATIONS . . . . . . . . . . . . . . . . . . . . . 4 - 1 4.1 BeneWin SCA-60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 4.1.1 Installation of BeneWin program . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 4.1.2 To start the BeneWin program . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4 4.2 BeneLoc . . . . . . . . . . . . . . . . .
Product: TDP-60-HN / 1.3.1999 5.2.9 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 33 5.2.10 Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 33 5.2.11 Control- and Output-Signals . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 33 5.2.12 Parts list OY1920 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 36 6.0 CAR ASSEMBLY KIT . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1 6.
Product: TDP-60-HN / General 1.3.1999 1.0 GENERAL General 1.1 TECHNICAL INFORMATION 1.1.1 Operational System NMT-450i 1.1.2 Dimensions Size: 56 x 145 x 23 mm Weight: 240 g Volume: 159 cm³ 1.1.3 Power Consumption - Batteries: 4x 1.2 V NiMH - Sleep current: 2 mA - Standby current: 43 mA - Conversation mode, high power: app. 0.9 A - Conversation mode, low power: app. 0.4 A Charger: - automatic 1 h rapid charging for NiMH batteries 1.1.
Product: TDP-60-HN / General 1.3.1999 - external antenna adapter - BeneWin - hand strap - belt clip 1.1.5 Alert Functions Adjustable ringing tones - type, 9 fixed, one changeable with BeneWin - volume - progressive or fixed Silent alert - short tone and ‘call is coming’ text in the display Vibrating alert - vibrator in optional batteries 1.1.
Product: TDP-60-HN / General 1.3.1999 1.1.8 Auto Answer; Pager/Hands Free - pre-set number of ring tones before answering (0...6) Pager - answers incoming calls and receives numeric messages - 9 memory locations (23 characters / location) Hands Free - answers incoming calls when connected to HF 1.1.
Product: TDP-60-HN / General 1.3.1999 1.1.10 Additional Exchange-Based Features Call management - New call - Pick incoming call - Select call MFT-function (DTMF signal transmission) 1.1.11 Manufacturer Benefon Oyj P.O. Box 84 24101 Salo Finland Tel. +358 2 77400 Fax. +358 2 7332633 2DP_60GB.
Product: TDP-60-HN / General 1.3.1999 1.2 PRODUCT FAMILY - BENEFON SPICA HANDPORTABLE TDP-60-HN - MAINS CHARGER CMA-60-230 - CIGARETTE LIGHTER CHARGER CCS 60-12 - DESKTOP CHARGER CTA-60 - LIGHT HOLDER KDC-60 - PORTABLE HANDS FREE EHD-60 - HANDS FREE CAR KIT This kit includes a charging holder KDS-60, carbox UDH-60, loudspeaker and microphone for hands free function, car radio mute and external alert facility. - EXTERNAL HANDSET WITH HOLDER HDS-50 This is an optional accessory for the hands free car kit.
Product: TDP-60-HN / General 1.3.1999 Benefon Spica And The Chargers Mains Charger Cigarette Lighter Charger Desktop Charger 2DP_60GB.
Product: TDP-60-HN / General 1.3.1999 Light Car Installation 2DP_60GB.
Product: TDP-60-HN / General 1.3.1999 Car Installation 2DP_60GB.
Product: TDP-60-HN / General 1.3.1999 Car Installation with BeneBoost 2DP_60GB.
Product: TDP-60-HN / General 1.3.1999 Other Accessories 2DP_60GB.
Product: TDP-60-HN / General 1.3.1999 BeneWin BeneWin 2DP_60GB.
2.0 OWNER’S MANUAL 1user_gb.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.0 INSTALLATION INSTRUCTIONS Installation Instructions 3.1 Phone Programming You can program Benefon Spica by using either the keys on your phone, or the BeneLoc computer program. In either case, you will need a localbox.
Product: TDP-60-HN / Installation Instructions 1.3.1999 It is possible to program the sales date ONLY ONCE, which means that you will not be able to change it again afterwards. If the sales date has not been programmed, your phone will not enter the normal stand-by mode. 3.1.1.2 Radio Path Identification 1. Press , and the following text will appear in the display: RADIO PATH ID [XXXXXXXXXX]. 2. Choose CHANGE.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.1.2 To program Using the BeneLoc Program power 5V log gen flash 5V log meter Start the installed program by clicking the icon. The phone must be connected to the system as discribed above. Main window Press Dealer-key to enter the programming window. 6DP_60GB.
Product: TDP-60-HN / Installation Instructions 1.3.1999 You can read the phone data by pressing the Read phone -key. You can change the miscellanous settings with the computer and transfer them to phone by pressing the Program phone -key. BeneLoc includes Help-program for further information. 6DP_60GB.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.2 CAR KIT The Car Kit includes a phone holder (KDS-60), a car box (UDH-60), an antenna, an installation base, a hf speaker, a microphone and a cable. The Car Kit sales package also includes an installation materials bag, which contains the necessary installation equipment. On the next page you will find a diagram of connections explaining how to install the Car Kit. Caution: The Car Kit should only be installed by Benefon authorized installer.
Product: TDP-60-HN / Installation Instructions 1.3.1999 the ground lead to the frame of the car with a short wire. 3.2.5 External Handset HDS-50 Install the external handset the same way as you installed the phone holder. 3.2.6 Car Box UDH-60 Place the car box out of sight inside the dashboard of the car or to another suitable place. First, connect the wires to the car box. Install the car box so that the heat sink has some space for cooling.
Product: TDP-60-HN / Installation Instructions 1.3.1999 A Diagram of Connections KDS-60 How to install a cable to a car box.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.2.8 BENEBOOST KIT The BeneBoost Kit is an extension for a car kit. It includes the BeneBoost car amplifier (TDB-60), a coaxial cable, a system cable and a power cable. The BeneBoost Kit sales package also includes an installation materials bag, which contains the necessary installation equipment. On the next page you will find a diagram of connections explaining how to install the BeneBoost Kit.
Product: TDP-60-HN / Installation Instructions 1.3.1999 (+)-wire of the power cable of the booster with a blade splice connector. IMPORTANT: If you install the BeneBoost after the car kit, you must first remove the car kit (+)-wire of the power cable from the battery and attach it as mentioned above. A Diagram of Connections A connector of the BeneBoost PIN 1 2 3 4 5 6 Name nc nc Ground nc nc Colour Vbatt, +12 V Red Black 5m 5m 6DP_60GB.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.3 HF-FUNCTION Benefon nSpica offers you hands free -setup for the Car Kit : the background noise tuning (CAR KIT TUNING) and MIC-ERP contrast tuning (CAR KIT SWING). 3.3.1 CAR KIT TUNING (theory) You can set up the activation level of the microphone by using the CAR KIT TUNING option. The level is correct when the microphone path is activated by voice alone, and not, for example, by background noise in your car.
Product: TDP-60-HN / Installation Instructions 1.3.1999 b. If the CAR KIT TUNING has been set up too low, the background noise in your car (2) will activate the microphone path, and the volume of the HFspeaker will be low. 50 (2) 40 Car kit tuning 30 c. When the CAR KIT TUNING has been set correctly only your voice (1 & 3) will open the microphone path. (1) (3) 50 Car kit tuning 40 30 (2) Benefon phones have been set in our factory so that they will function in most cars.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.3.2 CAR KIT SWING (theory) The four-step CAR KIT SWING tuning is used to set the contrast of the microphone amplification/speaker attenuation swing. In the following figures the swing position while listening to the Car Kit is indicated by a solid line and the position while speaking into Car Kit the indicated by a dotted line. a.
Product: TDP-60-HN / Installation Instructions 1.3.1999 3.3.3 HF-function tuning in practice You can tune HF-functions two ways: manually or with car kit. Manual tuning 1. Connect the localbox to your phone, and turn the phone on. 2. Press and the following text will appear in the display: ***BENEFON***. * will be flashing in the display. 3. Press , and the following text will appear in the display: HF-FUNCTION 4.
Product: TDP-60-HN / BeneWin 1.3.1999 4.0 SERVICE APPLICATIONS BeneWin 4.1 BeneWin SCA-60 The BeneWin SCM Program for Windows is designed to facilitate maintenance of phone numbers and user settings on Benefon mobile phones. You can also use your phone to carry out the commands in the BeneWin Program, but it is handier to process data using your screen and keyboard - the advantage of the BeneWin Program.
Product: TDP-60-HN / BeneWin 1.3.1999 In the Command Line box, type the letter A: or B: to indicate your floppy disk drive, and then type SETUP. For example, A:SETUP. Click the OK button, and follow the instructions displayed on your screen. As normal it is recommended to close all other applications when installing new SW into hard disk. Only Windows should be running. When you have confirmed that there is no other program running click Next.
Product: TDP-60-HN / BeneWin 1.3.1999 On the next phase you will determine Program Folder. Default value is "Benefon Applications". You may choose some other Folder or even crate a new one. When done click Next. Before the real installation starts you may accept or decline the settings. If you are satisfied click Next and the installation starts. 3DP_60GB.
Product: TDP-60-HN / BeneWin 1.3.1999 4.1.2 To start the BeneWin program Connect your phone with a cable to the serial port of your computer, which is called COM1 or COM2. The serial ports are located in the back of your computer, and more precise instructions can be found in the manual accompanying the computer. Plug the flat end of the cable into the connector at the bottom of your phone. When the cable has been connected and the phone is functioning, you can start the BeneWin Program.
Product: TDP-60-HN / BeneLoc 1.3.1999 4.2 BeneLoc BeneLoc power 5V log gen flash 5V log meter BeneLoc program is designed to help service person on tuning and service purpose. With Flasher Program you can change the software to Benefon phones. Both, BeneLoc and Flasher program will need Local Box with service rights to work. 4.2.1 Installation of BeneLoc program Start Windows. Close all other programs except Program Manager.
Product: TDP-60-HN / BeneLoc 1.3.1999 App\BeneLoc. Accept the drive and directory by clicking Next button. You can also type your own directory for Beneloc Program. The Setup Program creates all necessary directories and subdirectories to your computer. Setup Program also creates its own group window in Program Manager. 4.2.2 To start the BeneLoc program Connect the Service LocalBox to serial port of your computer, which is called COM1 or COM2.
Product: TDP-60-HN / BeneLoc 1.3.1999 4.2.3 Using the BeneLoc program In the main window of the BeneLoc, you will find submenus and buttons. Clicking the buttons you can go to the submenus. Change For changing phone to another similar you do not need to do more than enter into main menu. It means that this button is not needed. If you are going to change the tested phone to one having different software in, clicking Change will start the registration protocol again.
Product: TDP-60-HN / BeneLoc 1.3.1999 Service You can control the audio lines (for example, switch Rx audio and compander on/off) in the Service main menu. It is also possible to control the phone to desired channel. There is also possible to change the power of transmitter. In the Ports submenu is you can see the status of different digital ports. There is also possible to control some of the output ports. You can read the status of the A/D converters from the A/D submenu.
Product: TDP-60-HN / BeneLoc 1.3.1999 System You select used mobile phone system from this submenu. File From settings submenu you can manually change settings of the communication port. 3DP_60GB.
Product: TDP-60-HN / 1.3.1999 5.0 PHONE’S CONSTRUCTION 7DP_60GB.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 5.1 LOGIC / AUDIO OA1900 Processor/Audio PROCESSOR 5.1.1 General The entire radio audio and processor functions are found within a single PA1900 board, through which all other modules are connected. Only the RF signals have a different unit. The processor controls the audio and radio (RF) modules, internal devices and external accessories. The µCBIC (processor-asic) includes: µCBIC IG3010 PROM 29LV004 SIS IG2048 4A1900GB.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 5.1.2 Connectors: 5.1.2.1 Radio Base Connector, V101 1 2 3 4 charge voltage for battery charge voltage for battery battery voltage to accessory flash programming voltage external audio signal from the accessory + power on/off control (3V = pwr on) ground ground 6 - 8V / max 1,1A 6 - 8V / max 1,1A 4 7,5V / max 0,3A 0.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 5.1.2.2 Accu module, V102 1 2 3 4 A_VB A_BATD A_MC GND power supply voltage from the battery battery pack data Extra control-line 5V 0/VCC 0/VCC 5.1.2.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 13 14 15...17 18...23 24 25 26 27...34 35 36...40 41 VCC DAO VCC nc DSCL DSI GND VCC nc power supply voltage L:control data H:display data power supply voltage not connected serial clock line for data serial data input ground connected to the voltage components power supply voltage connected to the voltage components not connected 3.3V 0/VCC 3.3V 0/VCC 3.3V 5.1.2.6 Circuit Diagram The processor and audio circuits diagram is split into four parts.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 controlled by an µCBIC series output. The modem gives a 1200 Hz signal RXCLK and TXCLK to the µCBIC. There is a data detector within the modem, the speed of which is controlled by C413. The µCBIC A/D converter measures the level of acceptance from ERPDET line. The same detector also serves to control HF function. 5.1.3.4 AFC The AFC function is performed by an internal µCBIC frequency counter.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 is ensured during a battery-back change by the battery B200. 5.1.3.9 Battery Voltage Measurement The battery voltage is measured by an A/D converter (AN7).The converter 256 step conversion scale is not sufficient as it stands, so the measured range is rectricted to 4 8V by the operational amplifier I301. The reference voltage for the measurement is provided by the main regulator 3.3V supply.
Product: TDP-60-HN / OA1900 Processor/Audio 1.3.1999 5.1.3.14 Temperature Measurement The radio has two separate temperature sensors, one within the battery pack, and the other within the radio module. Inside the radio the NTC resistor R323 voltage is measured by the µCBIC A/D converter (AN6). This value is converted by a programmed table to a temperature reading. 5.1.3.15 Real-time Clock A real-time clock is provided within µCBIC to give the time and date.
Product: TDP-60-HN / OA1900 Audio 1.3.1999 Audio 5.1.4 Function Description OA1900 Audio The audio module is comprised of the following functions: 1. TX-audio signal handling 2. RX-audio signal handling 3. Fii signal handling 4. FFSK modem 5. DTMF generator/receiver 6. Signal level detectors 7. Compander 8. Expander 9. Buzzer The audio functions are mainly located in a single circuit AK2339. This chip from AKM is controlled by a serialbus.
Product: TDP-60-HN / OA1900 Audio 1.3.1999 deviation gain control circuit to set the transmit signal level. After the VR3 comes switch TXAUDON, which mutes the tx-audio signal using the TXMUTE control. From the switch, the signal is fed to the summing junction (ADD3) of the tx-audio signal and Fii-signal. Next comes VR4 gain control circuit to set. SMF1 is smoothing filter for tx-audio signal. The tx-audio signal is then fed to the V102 connector pin 20. 5.1.
Product: TDP-60-HN / OA1900 Audio 1.3.1999 detection level standard. Once the detector judges a valid FFSK signal, ’H’ signal is put out on the FFSKDET pin (pin43). The data detector speed is determined by the external condensator C413. FFSK DEMOD. To recover 1200bps receive data and clock from the FFSK signal. The modem is connected to the CPU by series lines, the receiver to a synchronised gate, and transmission is directed to an ASIC series output.
Product: TDP-60-HN / OA1900 Audio 1.3.1999 5.1.13 The other in audio asic (I401) OSC is the main oscillator and clock divider for the prosessor. CLKBUF is clock buffer generate clock out from main clock. INTERFACE & DATA REGISTER is a 16 bit address/data serial interface circuit. BIAS is bias current generator for amplifiers. TIMER is an 8 bit timer (not used). DA1, DA2, DA3 are 8 bit linear DA converters. 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 5.1.14 Parts list OA1900 OA1900 Proc./Audio CODE PART DESCRIPT. VALUE MANUF.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 The Top Side Layout PA1900 A1 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 The Bottom Side Layout PA1900 A1 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 AUDCLK AUDCSN RXREG SISRXD AUDDIN SCRCS SISSTR LIGHT GND SDA SCL MCLK ISCINT nmi GND sleout sleclk GND VRAM ALARM RESET md1 stby OE WE lwr CE RESET ISIGN I2CINT pe2 pe3 pe4 pe5 pe6 SPLITSW 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 4A1900GB.
Product: TDP-60-HN / OA1900 Proc./Audio 1.3.1999 4A1900GB.
Product: TDP-60-HN / OY1920 Synthesizer 1.3.1999 5.2 RF MODULE RX Synthesizer OY1920 Synthesizer 5.2.1 General The RX synthesizer generates an upper side injection frequency for the receiver. The injection frequency is fed to the receiver’s first mixer. Operating voltage Current consumption Output level to the receiver Frequency range 3.8 VDC 14 mA +1 dBm 540,550...545,025 MHz 5.2.2 Functional Description The RX injection frequency is generated with a phase locked loop.
Product: TDP-60-HN / OY1920 Synthesizer 1.3.1999 TX-Synthesizer 5.2.4 General The TX synthesizer generates the final modulated transmission frequency, which is fed to the transmitter. Operating voltage Current consumption Output level to the transmitter Frequency range 3.8 VDC <30 mA +6 dBm 453.000...457.475 MHz 5.2.5 Function Description The TX frequency is generated with a phase locked loop (PLL).
Product: TDP-60-HN / OY1920 Synthesizer 1.3.1999 5.2.6 Control- and Output-Signals VTXS TXAUDIO 12M85 SCLK SDATA SLE TXINJ AFC TXS_REG 4Z1900GB.fm TX synthesizer operating voltage (3.8 V) Transmitter audio signal 12.85 MHz signal to the receiver circuit.
Product: TDP-60-HN / OY1920 Receiver 1.3.1999 Receiver OY1920 Receiver 5.2.7 General The module contains all FM-receiver functional blocks. RF-amplifier 1. mixer 1. IF-amplifier FM IF system 3SK284 double-balanced mixer 3SK284 SA 607 includes the following blocks: 2. mixer IF limiter quadrature detector RSSI (received signal strength indicator) When the RF signal isreceived it is brought through the duplex filter to the amplifier stage Q101.
Product: TDP-60-HN / OY1920 Receiver 1.3.1999 5.2.8 Input- and Output-Signals RF input from the duplex filter RXINJ 12M85 VRX 450 kHz RXAUDIO RSSI 463,000...467,475 MHz RX injection signal to the double balanced mixer 12.85 MHz signal to the multiplier for the 2.mixer RX operating voltage 3.8V from the regulator Output from 2. IF to the AFC detector Receiver audio output 100mVrms Received signal strength indicator output 0,5...2V SENSITIVITY CHECK 4Z1900GB.fm channel RF input SINAD psof.
Product: TDP-60-HN / OY1920 Transmitter 1.3.1999 Transmitter OY1920 Transmitter 5.2.9 General Operating voltage Current consumption Input level from the synthesizer Output level to the duplex filter Frequency range 4.7 ... 6 v mid power max. 1.0 A low power max. 0.45 A +6 dBm mid power 33 dBm (2.0W) low power 24.7 dBm (0.3W) 453,000...457,475 MHz 5.2.10 Function Description The transmitter unit is comprised of three amplifier stages and two attenuator stages.
Product: TDP-60-HN / PY1900 1.3.1999 PY1900 The Top Side Layout PY1900A0 4Z1900GB.
Product: TDP-60-HN / PY1900 1.3.1999 The Bottom Side Layout PY1900A0 4Z1900GB.
Product: TDP-60-HN / OY1920-RF 1.3.1999 5.2.12 Parts list OY1920 OY1920-RF CODE PART DESCRIPT. VALUE MANUF.
Product: TDP-60-HN / OY1920-RF 1.3.1999 CODE CG0101 CG0101 CU3106 CC0223 CU0334 PART C326 C328 C329 C341 C342 DESCRIPT. SMD capasitor X7R SMD capasitor X7R SMD tantal SMD capasitor SMD tantalium capasitor VALUE 100pF ñ5% 100pF ñ5% 10uF / 6V +-20% 22 nF 10% 50 V X7R 0.
Product: TDP-60-HN / OY1920-RF 1.3.
Product: TDP-60-HN / OY1920-RF 1.3.1999 CODE LC3472 LC3273 LC3334 LC3104 LI0450 LC3224 LC1224 LC1224 LC3183 PART L106 L107 L201 L202 L203 L204 L301 L401 L430 DESCRIPT. SMD inductor SMD inductor SMD inductor SMD inductor SMD Quad. coil SMD inductor SMD inductor SMD inductor SMD inductor VALUE 4n7 -+2% 27nH -+2% 330nH +-10% 100nH+-10% magnet.shielded 450kHz 220nH+-10% magnet.
Product: TDP-60-HN / OY1920-RF 1.3.
Product: TDP-60-HN / OY1920-RF 1.3.1999 CODE RG0102 RG0102 RG0271 RG0103 RG0184 RG0104 RG0103 RG0151 RG0220 RG0224 RG0105 RG0101 RG0220 RG0220 RG0220 RG0102 RG0332 RG0102 RG0102 VM0019 OD1920 XM0006 XF7755 XC3450 XC4450 XR1650 XO4128 XR1550 XI0005 LF0062 PY1900 MD1900 MD1901 MD1902 MD1902 PART R611 R612 R613 R615 R616 R617 R618 R619 R620 R621 R622 R623 R624 R626 R627 R628 R629 R630 R631 V600 X100 X102 X103 X201 X202 X301 X360 X401 X600 X610 YPCB2 YST40 YST40 YTX1 YTX2 DESCRIPT.
Product: TDP-60-HN / OY1920-RF 1.3.1999 4Y1920GB.
Product: TDP-60-HN / OY1920-RF 1.3.1999 4Y1920GB.
Product: TDP-60-HN / OY1920-RF 1.3.1999 4Y1920GB.
Product: TDP-60-HN / OY1920-RF 1.3.1999 4Y1920GB.
1.3.1999 6.0 CAR ASSEMBLY KIT CAR ASSEMBLY KIT 8CARA_GB.
Product: UDH-60 (Carbox) / YO1951 1.3.1999 6.1 CARBOX UDH-60 YO1951 6.1.1 Including attached functions - power supply filter - voltage regulators - processor controlled battery charger - controls for external relays (AL, MUTE) - handsfree amplifiers - PC/AUX-connector - handset connector - integrated branching unit 6.1.2 Connector descriptions 6.1.2.1 EXTVB V100 1 MUTE 2 GND 3 GND 4 AL 5 HF_SPKR 6 VBATT 8UDH60GB.
Product: UDH-60 (Carbox) / YO1951 1.3.1999 6.1.2.2 HANDSET V102: 1 2 3 4 HS_ERP EGND MGND HS_MIC Audio signal for earphone + HOOK-signal HS Microphone signal to carbox 6.1.2.3 EXTMIC V103 1 2 3 4 5 GND NC HFMIC GND NC ground not connected HF Microphone signal to carbox ground not connected 6.1.2.4 PC/AUX V104 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 8UDH60GB.
Product: UDH-60 (Carbox) / YO1951 1.3.1999 6.1.2.5 BOX V105 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 V_CHARGE V_CHARGE V-BAT NC EXTMIC P_GND GND EXTERP CADET I2CINT SCL SDA TXD RXD EXTIO 16 CHGCONT battery charging current battery charging current battery voltage not connected external microphone signal ground ground external ERP-signal external tanget I²C interrupt I²C clock I²C data RS 232 RS 232 extra-IO charging control from the processor max. 1.1A / 8V 200 mV RMS 100 mV RMS +3.3 V 6.1.2.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 6.1.3 Parts list OW1951 OW1951 CODE PART DESCRIPT. VALUE MANUF.
Product: UDH-60 (Carbox) / OW1951 1.3.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 CODE CD0101 CE0476 CD0101 CD0104 CP0155 CE3106 CE0127 CE0476 CD0103 CD0101 CD0103 CD0101 CE3106 CD0103 CH0105 DT0033 PART C516 C520 C521 C522 C530 C531 C534 C535 C540 C541 C550 C551 C560 C561 C580 D100 DESCRIPT.
Product: UDH-60 (Carbox) / OW1951 1.3.
Product: UDH-60 (Carbox) / OW1951 1.3.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 CODE RD0333 RD0103 RD0103 RD0153 RD0224 RD0104 RD0102 RD0104 RD0564 RD0104 RD0564 RD0102 RD0332 RD0221 LT0005 VW0106 VN0003 VN0005 VM0342 VM0116 LF0061 LF0061 PART R573 R574 R575 R576 R577 R578 R579 R580 R581 R582 R583 R584 R585 R586 T530 V100 V102 V103 V104 V105 X100 X101 DESCRIPT.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 The Top Side Layout PW1951A1 8UDH60GB.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 The Bottom Side Layout PW1951A1 8UDH60GB.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 8UDH60GB.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 8UDH60GB.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 8UDH60GB.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 8UDH60GB.
Product: UDH-60 (Carbox) / OW1951 1.3.1999 8UDH60GB.
Product: UDH-60 (Carbox) / YO1951 / Mechanics 1.3.1999 YO1951 / Mechanics MF 1502 MD 0702 NC 2008 8 pcs OW 1951 NC 2066 NG 1015 NF 0200 2 pcs NG 0011 NC 2010 NG 0012 MF 1140 MD 0703 UDH-60 Carbox YO1951 8UDH60GB.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 6.2 EXTERNAL HANDSET WITH CRADLE HDS-50 6.2.1 External Handset (not serviceable) 6.2.1.1 Mechanics External Handset HDS-50 YH0442 8HDS50GB.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 6.2.1.2 Cable 1500 4 F14 1 X 360 COILED FLAT CABLE (4.8x2.6) 4 POS.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 6.2.3 Connector XIN Signals 1 2 3 4 ERP GND GND MIC earphone input, HOOK state ground ground microphone output 6.2.4 Microphone Sensitivity: -43 dB ± 6 dB Vendor and part no: Hosiden KUC2023 or KUB2023 33 pF; Size: 0805; Mounted on the microphone element. RF decoupling capacitor: 6.2.5 Speaker Sensitivity 95 dB ± 5 dB Vendor and part no: Impedance: Resistance (DC): Hosiden KDR0928-IE-0030 min 120 ohm max 3 kohm 6.2.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 6.2.7 Parts list OO0009 CODE PART DESCRIPT. VALUE MANUF. TYPE CU0475 CD0221 CD0221 CD0221 CD0221 PO0009 RP0222 RD0222 AR0016 AE0018 AM2024 VM0204 C106 C108 C110 C112 C114 M100 R100 R102 S102 XERP XMIC XIN SMD tantal SMD capasitor SMD capasitor SMD capasitor SMD capasitor PCB for OO0900 Edge control pot. SMD resistor Reed-relay Assembled earphone unit Assembled microphone unit Contact strip angle 4.7uF/16V 20% 4.7X2.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 The Top Side Layout PO0009A1 (Schematic OO0009A1) 8HDS50GB.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 The Bottom Side Layout PO0009A1 (Schematic OO0009A1) 8HDS50GB.
Product: HDS-50 (Ext. Handset With Cradle) / HLS-41, HDS-50, HXS-40 1.3.1999 8HDS50GB.
Product: HDS-50 (Ext. Handset With Cradle) / 1.3.1999 6.2.8 Cradle 6.2.8.1 Mechanics 8HDS50GB.
Product: TDB-60-N/B / 1.3.1999 7.0 BENEBOOST 8tdb60gb.
Product: TDB-60-N/B / 1.3.1999 7.0.1 TECHNICAL INFORMATION Car amplifier for Benefon Spica/Titan NMT 450i HP weight: 1190g size (l x w x h): 190x110x60 mm high power: 15 W supply voltage: 10.8 - 15.6 V power consumption - charging off: app. 130 mA BeneBoost + car kit - charging on: <1000 mA BeneBoost + car kit - conversation mode, high power: <5000 mA BeneBoost + car kit antenna connectors: TNC cooling: DC fan 7.
Product: TDB-60-N/B / 1.3.1999 TX0 TX1 HITEMP TXON Power OFF x x x HIGH PL1 150 mW LOW LOW HIGH LOW PL2 1.5 W HIGH LOW HIGH LOW PL3 15W LOW HIGH LOW LOW PL3 7W LOW HIGH HIGH LOW 7.1.2 Front end amplifier Between duplex filters X1 and X2 is a one transistor stage Q7 which amplifies a RX signal to a proper level to the phone. It compensates losses generated in the duplex filters and RF cables. The amplifier is operational as long as the phone is fixed in the phone holder. 7.1.
Product: TDB-60-N/B / OC1910 1.3.1999 7.1.5 Part lists OC1910 OC1910 CODE PART DESCRIPT. VALUE MANUF.
Product: TDB-60-N/B / OC1910 1.3.1999 CODE IR2952 IA0272 IX0623 IR2952 II8574 LC3822 LC2154 LF0396 LF0396 LC2154 LC2104 QS0848 QS0848 QS0031 QS0848 QS0848 QS0848 QS0858 QS0848 QA0035 QS0848 QS0848 QS0848 QS0848 QA4869 QF7002 QP0132 RF0473 RF0271 RF0271 RF0820 RF0473 RF0153 RF0102 RF0103 RF0222 RC0100 RC0100 RF0821 RC0100 RF0221 RF0222 RF0391 RF0331 RF0223 RF0223 RF0223 RF0223 RF0103 RF0151 RF0103 RI1103 RF0184 RF0823 RF0474 RF0474 RF0104 RF0104 RF0103 RF0474 8tdb60gb.
Product: TDB-60-N/B / OC1910 1.3.
Product: TDB-60-N/B / OC1910 1.3.1999 The Top Side Layout PC1900A3 8tdb60gb.
Product: TDB-60-N/B / OC1910 1.3.1999 The Bottom Side Layout PC1900A3 8tdb60gb.
Product: TDB-60-N/B / OC1910 1.3.1999 8tdb60gb.
Product: TDB-60-N/B / OC1910 1.3.1999 8tdb60gb.
Product: TDB-60-N/B / OC1910 1.3.1999 8tdb60gb.
Product: TDB-60-N/B / OC1910 1.3.1999 8tdb60gb.
1.3.1999 8.0 OTHER ACCESSORIES OTHER ACCESSORIES 8OTHE_GB.
Product: EHD-60 (Headset) / 1.3.1999 8.1 PORTABLE HANDS FREE KIT EHD-60 The Benefon portable hands free kit is designed to make the use of a mobile phone easier in various working situations. When you plug the portable hands free kit into your phone you can make and answer phone calls and use your hands at the same time. The portable hands free kit consists of an earpiece/microphone part and an adapter (EHD-60). 8.1.1 SPECIFICATION FOR HEADSET ADAPTER OO0313 8.1.1.
Product: EHD-60 (Headset) / 1.3.1999 8.1.2.2 Cellular phone connector V100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 NC NC VBATT NC EXTMIC GND GND EXTERP CADET NC NC NC NC NC EXTIO NC battery voltage microphone signal ground ground earphone signal not used external I/O 8.1.3 Operation Operating voltage is fed to pin VBATT (V100.3). It is regulated to 3.3 V (VB) with I101. Reference voltage VB/2 is produced with voltagedivider R120 and R 121. Bias voltage to microphone is fed through R100, R101 and R102.
Product: EHD-60 (Headset) / 1.3.1999 8.1.4 Parts list OO0313 CODE PART DESCRIPT. VALUE MANUF.
Product: EHD-60 (Headset) / 1.3.1999 CODE RF0103 RF0103 RF0472 RF0103 RF0103 VN0342 VN0009 PART R133 R140 R141 R142 R151 V100 V101 DESCRIPT. SMD resistor SMD resistor SMD resistor SMD resistor SMD resistor SMD system connector Stereo jack VALUE 10 k 5% 0.125 W 10 k 5% 0.125 W 4.7 k 5% 0.125 W 10 k 5% 0.125 W 10 k 5% 0.125 W 16 pin 2,5mm miniature MANUF. Kamaya Kamaya Kamaya Kamaya Kamaya AMP Hosiden TYPE 338271-1 HSJ1603-010020 Last update 18.03.98 8EHD60GB.
Product: EHD-60 (Headset) / 1.3.1999 The Top Side Layout PO0313 The Bottom Side Layout PO0313 8EHD60GB.
Product: EHD-60 (Headset) / 1.3.1999 8EHD60GB.
