MP610 / MP720 / MP770 Ceiling Mounting Guide Welcome
Copyright Copyright 2005 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
Packing Parts List CEILING ADAPTER PIPE PROJECTOR ADAPTER WASHER x 1 U-PLATE PIPE-BASE V – ADJUST BOLT M4 SCREW x 10 TUBE H – ADJUST ADAPTER NUT x 7 BOLT x 6 (TUBE BOLT x 2, L – ADJUST BOLT x 2, PIPE BOLT x 2) Names of Parts U - PLATE CEILING ADAPTER M4 SCREW x 2 TUBE Nut TUBE BOLT x 2 L-ADJUST BOLT x 2 PIPE PIPE BOLT x 2 M4 SCREW x 4 H - ADJUST ADAPTER V – ADJUST BOLT PIPE BASE M4 SCREW x 3 PROJECTOR ADAPTER Packing Parts List 3
Projector Installation and Throw Distance Chart Floor Installation for a 4:3 screen Maximum zoom Minimum zoom Screen Center of lens Vertical Offset Projection distance Feet Inches mm 4 48 5 6 60 72 7 8 84 96 9 108 10 120 12 144 15 180 18 216 25 300 1219 1500 1524 1829 2000 2134 2438 2500 2743 3000 3048 3500 3658 4000 4572 5000 5436 6000 7620 Distance from Screen in mm Min length Average Max length (with max. (with min.
Installing a Projector with The Ceiling Bracket Overview Q Diagram of completed installation Q Ceiling Mount Device Installation Procedure Insert the U-PLATE into the CEILING ADAPTER, and tighten two M4 screws (from the bottom) into the STEP A screw holes. Then attach the top part to the ceiling.
STEP B Install the TUBE and the U-PLATE with 2 sets of bolts & nuts (TUBE BOLT). NUTS x 2 TUBE BOLTS x 2 TUBE STEP C Install the PIPE and the TUBE with 2 sets of bolts & nuts (L-ADJUST BOLT). NUTS x 2 L-ADJUST BOLTS x2 PIPE STEP D Install the base-assembly. STEP D1 Attach the PIPE-BASE to the H-ADJUST ADAPTER with 2 M4 screws. M4 screw STEP D2 Assemble the PROJECTOR ADAPTER and the projector with 3 M4 screws.
STEP E Combine the H-ADJUST ADAPTER (including the PIPE-BASE) and the PROJECTOR ADAPTER with one V-ADJUST BOLT set (bolt, washer and nut). Then tighten the M4 screws on both sides. NUT WASHER H-ADJUST ADAPTER M4 screw V-ADJUST BOLT Assemble BASE-ASSEMBLY and the ceiling mount device with 2 sets of bolts and nuts (PIPE BOLT sets). *Two people are required for the completion of this step. STEP F Ceiling mount bracket NUT BASE-ASSEMBLY PIPE BOLT Installation finished.
Adjusting the Ceiling Bracket Height Adjustment 1. 2. 3. 4. 5. Make sure to remove the projector first. Loosen the nuts securing to the two L-ADJUST BOLTS. Remove the L-ADJUST BOLTS from the PIPE. Adjust to the correct position for the height of the screen. The height can be adjusted to 218mm or any value in a range between 548mm and 758mm in increments of 30 mm. Insert the L-ADJUST BOLT back into the PIPE, and then re-attach the nuts previously removed.
Horizontal Angle Adjustment 1. 2. 3. 4. Loosen the two sets of screws connecting the PIPE-BASE and the H-ADJUST ADAPTER. Adjust the horizontal angle so that it is correct for the orientation of the screen. Re-tighten the two sets of screws connecting the PIPE-BASE and the H-ADJUST ADAPTER. The swivel angle can be set within a range of negative to positive 30 degrees. Vertical Angle Adjustment 1. 2. 3. 4. Loosen the two sets of screws connecting the H-ADJUST ADAPTER and the PROJECTOR ADAPTER.
Specifications and Diagrams Specifications Adjustment Range Height Horizontal angle Vertical angle 218mm, 548mm, 578mm, 608mm, 638mm, 668mm, 698mm, 728mm and 758mm. –30 to +30 degrees +5 to -15 degrees Weight 3.2 kg Loading 3.
