Benq Wireless LAN PCMCIA Adapter AWL100 User Manual Version 1.
MPE Statement (Safety Information) Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. Safety Information In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance 2.5cm between the radiator and your body. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.
Federal Communications Commission (FCC) Requirements, Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Benq Wireless LAN Contents Contents .......................................................................................................................... i 1. Installation..................................................................................................................1 1.1 Driver Installation....................................................................................1 2. AWL100 Wireless Settings ..................................................................................
Benq Wireless LAN 1. Installation 1.1 Driver Installation Insert AWL100 PCMCIA Adapter into your PC, and then Windows will show the dialog – ‘Add New Hardware Wizard’. Select ‘Search the location of the driver’ and press Next button.
Benq Wireless LAN Select ‘Specify a location’ and browse the Benq Wireless LAN CD to find AWL100. For example, if your CD-ROM is drive D and you want to install the English version of driver, the location is D:\AWL100\English. Windows has found AWL100 PCMCIA Adapter. Press Next button. Please wait while coping files.
Benq Wireless LAN Press Finish. Press Yes and restart your computer. 2. AWL100 Wireless Settings You can launch AWL100 Wireless Settings utility by clicking the icon or from Control Panel.
Benq Wireless LAN AWL100 PCMCIA Adapter User Manual 4
Benq Wireless LAN 2.1 Status State The current state of the driver is displayed in this field. If the state reveals “Associated,“ it means that the normal flow of operation is in Infrastructure mode. This shows that the PC is already connected to access point and BSSID is also shown in the form of hex digits. At the same time, the networking is available for the device.
Benq Wireless LAN Current Tx Rate This field shows the current radio channel which is being used for an active connection. Current Channel This field shows the current radio channel which is being used for an active connection. Throughput The instantaneous wireless Receive and Transmit throughput are displayed in bytes per second in this field. Every two seconds, these values are updated. Link Quality This field reveals the quality of the current connection.
Benq Wireless LAN 3.2 Configuration Several fields illustrated as following are offered by the Configuration Tab. Operating parameters of the driver can be viewed or changed here. Under the circumstances,. changes to any of the parameters in this panel can be applied to the driver without the need to reboot the PC. Default: Apply: It restores each field in the panel to its default value by pressing this button.
Benq Wireless LAN with. Network Type You can select from a list of supported network types in this field. These network types displayed will have two values as following: “Access Point,” and “Peer-to-Peer”. Access Point (Infrastructure) This is an operation mode which requires the existence of an 802.11 Access Point.
Benq Wireless LAN A-F are valid entries. Therefore, if entered incorrectly, the program will not write keys to a driver. Alternatively a Pass-phrase can be entered which is used as a “seed” to randomly generate the four keys. Since the same keys must be entered into each node on the wireless network, this saves considerable time while setting. - Key 1 – Key 4 When you want to enter the keys manually, you may use these four fields.
Benq Wireless LAN Join Select the SSID you want to be associated with, and then press this Join button to join this network. 3.5 About You may learn the product version including the detail of Network Driver, Configuration Utility, and NIC firmware version from this “About” tab. When users want to report their problems to technical support, they must use this version number.
