BenQ S670C Mobile Phone User’s Manual
Copyright © 2004. BENQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BENQ Corporation. * This publication includes images from CorelDRAW® 9 which are protected by the copyright laws of the U.S., Canada and elsewhere.
Safety Information For your safety, please read the guidelines below carefully before you use your phone: Exposure to Radio Frequency Signals Max. SAR measurement: GSM900: 1.25 mW/g; DCS1800: 0.104 mW/g. Your wireless handheld portable telephone is a low power transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. European and international agencies have set standards and recommendations for the protection of public exposure to RF electromagnetic energy.
Antenna Care Use only the supplied or approved replacement antenna. Unauthorized antennas, modifications or attachments may damage the phone and violate FCC regulations. Phone Operation Normal Position: Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder. For your phone to operate most efficiently, do not touch the antenna unnecessarily when the phone is in use.
Electronic Devices Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone. Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six (6") inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker.
Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. Posted Facilities Turn your phone OFF in any facility where posted notice so requires. Aircraft FCC regulations prohibit using your phone while in the air. Switch OFF your phone before boarding an aircraft.
For Vehicles Equipped with an Air Bag An air bag inflates with great force. DO NOT place objects, including both installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.
vi Safety Information
Table of Contents Safety Information ...........................................................i 1. Preparing Your Phone For Use................................... 1 Inserting a SIM Card ............................................................ 1 Installing a Battery and Charging the Phone ...................... 2 Turning the Phone On ......................................................... 5 2. Getting to Know Your Phone ..................................... 7 Your Phone at a Glance..................
Making an Emergency Call ................................................ 36 Dialing an Extension Number ........................................... 36 Speed Dialing ...................................................................... 36 Voice Dialing ...................................................................... 36 Listening to Voicemails ...................................................... 37 Phone Book.........................................................................
Outbox ....................................................................................78 Drafts.......................................................................................79 Voicemail ................................................................................80 Message Settings .....................................................................80 Cleanup Messages...................................................................85 Memory Status ........................................
Call Records ........................................................................ 99 Missed Calls ............................................................................99 Received Calls .........................................................................99 Dialed Calls.............................................................................99 Delete All.................................................................................99 Call Duration.........................................
Internet.............................................................................. 119 WAP Service .........................................................................119 Start Browser ............................................................................. 120 WAP Message............................................................................ 126 Enter Address ............................................................................ 126 Resume ..........................................
Backlight Setting ....................................................................... 153 OLED Duration......................................................................... 153 OLED Animation Setting ......................................................... 154 Audio.....................................................................................154 Power Saving Mode..............................................................154 Call Settings ..................................................
5. Care and Maintenance ............................................ 165 6. Troubleshooting......................................................
xiv Table of Contents
Preparing Your Phone For Use Inserting a SIM Card 1. Turn the phone over, and release the battery latch. Lift the battery off the phone. Battery latch Do not remove the battery when the phone is on. Doing so could cause you to lose personal settings or data stored either on your SIM card or in the phone's memory. 2. Slide the SIM card in under the metal plate in the SIM card slot, with the SIM card's metal contacts facing down and the cut corner at the top right.
you wish to remove the SIM card, you / Ifmust first press down the stay, then push the SIM card out of the slot. Stay SIM card Installing a Battery and Charging the Phone 1. With the battery's metal contacts facing down, align the protruding tabs on the end with the holes in the battery bay of the phone. Then push the battery toward the end of the bay to insert the battery's tabs into the holes. Press down to click the battery in place.
2. Insert the charger connector into the charger socket on the bottom of the phone. Make sure that the connector is inserted in the correct orientation (with the arrow pointing up). Charger socket Charger connector 3. Insert the charger into a power outlet. 4. Once the phone is fully charged, remove the charger from both the power outlet and the phone.
requires approximately 4 hours. / •• Charging When charging the phone while it is turned off, the external and main displays will be activated, and the status indicator light will flash blue (during the charging process, the external display will show the time and cycle through 3 animations, then turn off temporarily. This is normal. • During charging, in the external display's battery indicator , the lines showing the battery power level will scroll until the battery is fully charged.
Turning the Phone On 1. Open the phone's flip. 2. Press and hold to turn the phone on. The phone will display the welcome animation. can select and set a welcome animation, image, or message / • You that will display when you turn on your phone, as well as the music that will be played. Go to the menu: Settings → Display → Welcome Message. For details, please refer to page 152. • If the welcoming music goes on too long, once the standby screen comes up, you can press to stop playback. 3.
automatically search for the designated network. This search process may take a few seconds. 5. The phone will then ask you whether you wish to activate the phone book stored in the phone's memory or on your SIM card. Press to highlight the desired phone book and then press to open the phone book you have selected. 6. After you open the phone book on the SIM card, any data you browse, store, or delete will be from the SIM card's phone book.
Getting to Know Your Phone Your Phone at a Glance The figure below shows the main parts of your phone: Front view 1 Antenna Status indicator light External display External speaker Getting to Know Your Phone 7
Front view 2 Earpiece Main display OK key Left soft key Dial/Answer key Scroll key Right soft key Power on/off key Messages menu key Alphanumeric keys Microphone 8 Getting to Know Your Phone
Side and back views Hands-free headset/Data cable jack Volume key Neck strap socket Mirror used to take self photos DC lens Getting to Know Your Phone 9
Active Flip Feature Opening the flip allows you to answer an incoming call. Closing the flip ends a call, cancels dialing, or rejects an incoming call. can turn the active flip feature on or off. To do so, go to the menu: / You Settings → Flip Activate. Status Indicator Light The status indicator light has the following functions: • Flashes blue when the phone detects a network or is charging. • Flashes purple when the battery is fully charged. • Flashes blue rapidly when there is an incoming call.
Standby Screen External Display When the flip is closed, the external display's status bar will show icons for network signal strength, battery power, and alarm (if active). The current time and an animation will appear in sequence. The external display can also alert you to incoming calls, text messages, and missed calls. you wish to set the time shown on the external display, go to the / • Ifmenu Settings → Date & Time → Time. See page 145.
Icons in the External Display's Status Bar Icon Function Description Signal strength Signal strength of the network. The more bars indicated, the stronger the signal. Battery status Shows the current level of battery power. The more bars indicated, the more power that remains. Four bars: fully charged. No bars: immediate charging needed. When charging the phone, the icon will scroll through the bars until the battery is fully charged.
Icon Function Description Outdoors Shows that the Outdoors profile is in use. Personal Shows that the Personal profile is in use. Handsfree Shows that the Handsfree profile is in use. Divert Shows that the call divert function is active.To set the call divert function go to the menu Settings → Call Settings → Call Divert. See page 155.
Main Screen Status bar Name of network operator Time and date Wallpaper Soft key bar Press to enter the Phone Book 14 Press to enter the main menu. Getting to Know Your Phone Press to use the camera function.
can set the animation or image you wish to use as wallpaper / • You when the phone is in standby mode by going to the menu Multimedia → Picture or Animation. Alternatively, you can go to the menu Settings → Display → Wallpaper. See page 134 and page 151. • To set the current time and date, as well as the format in which they will be shown in the main display's standby screen, go to the menu Settings → Date & Time. See page 145.
Icons in the Main Display's Status Bar Icon Function Description Signal strength Signal strength of the network. The more bars indicated, the stronger the signal. Battery status 16 Shows the current level of battery power. The more bars indicated, the more power that remains. Four bars: fully charged. No bars: immediate charging needed. When charging the phone, the icon will scroll ehrvicehsc t tha0.9(v beeh)(n acSsi)11.2vcated on y(our)]TJ0 -1.2931 TD0.0035 Tc0.001 through the bars u [(t4Ssi)11.
Icon Function Description Line in use Shows the number of the line currently in use. To set the line, go to the menu Settings → Call Settings → Active Line. For details, see page 158. Vibrate In the standby screen, press and hold to activate the silent profile. See page 52, "Using the Silent Profile". Normal Shows that the Normal profile is in use. To set the operating mode, go to the menu Settings → Profiles. See page 147. Meeting Shows that the Meeting profile is in use.
Using the Keys in the Standby Mode 8 In this user manual, "long-press" means to press and hold down a key for about two seconds before release. "Press" means to press a key and release immediately. 8 The chart below is meant only to introduce the commands accessible with keys when the phone is in standby mode. For information on other key commands available in other operating modes, see the pertinent sections in this user manual.
Key Commands and functions Power on/off key • Long-press to turn the phone on or off. • Press this key to reject incoming calls or cancel a call being dialed. Send/Answer key • Press to send or answer a call. • Long-press and your phone will automatically call the last number dialed. • Press to access the list of last missed/dialed/received calls. OK key • Press to open up the main menu and show its first item. Left soft key • Press to access the Phone Book (when PBook is shown).
Key Commands and functions Scroll key • Press to open the main menu and show its first item. • Press to enter the menu for function and phone number shortcuts. For information about the shortcuts menu, see page 58. • Long-press to activate voice dialing. • Long-press to activate the voice memo function. Messages menu key • Press this key to enter the Messages menu. For a description of the Messages menu, see page 62. Asterisk key • Press this key to enter an asterisk " * ".
Key Commands and functions ~ Alphanumeric keys • Press to enter digits in a phone number. • Shortcut key: Long-press a key to immediately access the function, or dial the number, that it represents. See page 58, "Shortcuts Menu". Volume key • Long-press the upper or lower portion of this key, located on the left side of the phone, to adjust the ring tone volume. Press the upper portion of this key or to increase the volume. Press the lower portion of this key or 8 When to decrease the volume.
Alphanumeric keys Key Digit Key Digit/Symbol/Function 1 7 2 8 3 9 4 0 5 * + (long-press) 6 # P(long-press after entering a phone number) 8 Long-pressing an alphanumeric key will access the function it represents, or dial the number that has been assigned to it (shortcut function).
Menu Navigation When the phone is in standby mode, press or to bring up the main menu and highlight the first item in that menu: Phone Book. 8 For details on how to use the various functions listed in the menu, see page 93, "Menus". can choose a display color for the menus by going to the menu / You Settings → Display → Theme. See page 151. Main menu The main menu item to which you have scrolled will be displayed as an animation. The name of the main menu item you have scrolled to.
Sub-menus The highlighted row is the currently selected item. The name of the current menu. Press to scroll up or down to an item. Press to bring up the previous screen. Press to enter the highlighted menu item for editing. Press to bring up the next screen. Press to return to the previous menu or screen. Press to enter the sub-menu represented by highlighted item or to activate the highlighted function. Pop-up menus Press to scroll up or down to an item. Press to close a pop-up menu.
Turning a function on or off Press to turn the selected function on or off (the currently selected function will be highlighted). After the selected function is activated, the display will usually show further setting options. Press to scroll to the desired setting option. Press to cancel and return to the previous screen. Press setting. Press or to edit the setting.
Menu navigation example The example given below demonstrates how to use menus to change the language setting. Regular access 1.In the standby mode, press or menu. to open the main 2.In the main menu, press to scroll to the Settings menu icon. Press menu. to enter this 3.In the Settings menu, press to scroll to the Language item (press to bring up the next screen, or press to bring up the previous screen), then press to enter the Language menu.
4.Press to scroll to the language you wish to use. Then press to confirm your selection. If, for example, you wish to set English as the display language, scroll to highlight English, and then press . The display will automatically return to the Settings menu, displayed in English. 5.Press (Back) repeatedly or press once to return to the standby screen. Access through number shortcuts 1.In the standby mode, press or to bring up the main menu.
2.The location of items in the main menu corresponds to the position of the to keys in the alphanumeric keypad. Thus, pressing will bring up the Settings menu. 3.In the Settings menu, the alphanumeric keys to represent menu items 1 to 10. Since Language is item number 10 in the Settings menu, pressing will bring up the Language submenu. 4.Press the alphanumeric key that corresponds to the language you wish to select, as it is listed in the Language sub-menu.
5.Press (Back) repeatedly or press once to return to the standby screen.
Main menu map Select To enter When using the phone book stored in your SIM card's memory, the seventh item is SIM Status. There is no Privacy Manager item.
Select To enter If your network vendor provides SIM toolkit valueadded services, they will appear as item number 11.
Select 32 Getting to Know Your Phone To enter
Using Your Phone Making a Phone Call Open the flip and make sure that the standby screen is shown on the main display. Enter the desired number using the alphanumeric keys to . Press to dial your call. / During a call, you can use the options. See page 49, "Call Menu". To modify a phone number that you have entered, press (Clear) to delete individual digits. Long-press (Clear) or press all digits entered and return to the standby screen.
Answering a Phone Call When a call is received, your phone rings or vibrates, with the display showing the caller's number (if supported by your network vendor). If the caller is a contact stored in the Phone Book, the phone will show the name recorded in the Phone Book. caller is a member of a caller group, the ring tone assigned to / • Ifthisthegroup will sound. The display will show the animation that is associated with this group as well, to help you identify the caller.
Rejecting an Incoming Call dihr s a s we s al te l q 7 r 4• 8Regardless 2 T f 1 0 . 1of1 whether 7 0 3 T mthe - 8flip q 0 is 3 Tfc7i .n9.c0 0 0 t h e u p p e m 2 - 2 3 . ( j ) -gilo n 0 3o 6 6 2 2 2 0 0 T f 1 0 . 1 0 7 0 0 r g 0 .
Making an Emergency Call To call emergency services, enter 112 (the international emergency number) and then press to dial the call. You can make an emergency call even if your phone is locked or cannot access your network, or there is no SIM card inserted, so long as you are within range of a network of the type supported by your phone. Dialing an Extension Number After you enter a telephone number, long-press , The phone display will show "P".
a. If there is only one phone number stored for the contact identified, your phone will automatically dial this number. b. If there are two or more phone numbers stored for the contact identified, the display will show the contact's Phone Book data. You can then scroll to the number you wish to dial, pressing or to make the call. 8 To use voice dialing to make a call, you must have stored a voice dialing prompt for the desired number in Phone Book.
Phone Book Adding Contacts to the Phone Book The Phone Book will have different formats and data headings depending on whether you have chosen to use a phone book stored on your SIM card or in your phone's memory. 8 The phone book in your phone's memory can store up to 500 contacts. The capacity of a phone book on your SIM card depends on the particular service provided by your network vendor. SIM card Phone Book 1. In the standby screen, enter the phone number that you wish to store, then press (Save).
Used to select a caller group for the contact. Press to select a group and then press . When there is an incoming call from this contact, the ring tone assigned to this group will sound and the display will show the animation/image associated with the group. 8 To set a ring tone and animation/image for each caller group, go to the menu Phone Book → Caller Group. See page 94. 8 You can also go the menu Phone Book → Caller Group to set a caller group for a contact.
Phone Book in the phone's memory 1. In the standby screen, enter the phone number you wish to store, and then press (Save). The display will show the default data fields for a new contact. 2. In the contact data screen, scroll to the data field that you wish to edit, and then press (Options) to bring up a pop-up menu. You can then use the following options with the contact data: • Edit: Edit the information in the selected field.
in order for the contact's data to be stored in the Phone Book. 8 If you do not wish to save a modified Phone Book record, press or (Back) to abort. 8 You can also add a new contact by going to the menu Phone Book → Add. • The default data fields for a contact are as follows: The contact's name. The contact's mobile phone number. The contact's home phone number. The contact's e-mail address. Used to assign a contact to a caller group. Press group, and then press to select a .
Other phone number for the contact. The contact's home address. The contact's work address. The contact's company name. The contact's department name. The contact's job title. Used for notes about the contact. Used to mark dates of special significance associated with the contact. Used to set a ring tone for the contact. When there is an incoming call from the contact, the phone will play this ring tone.
to scroll through the names (listed in alphabetical order) • Press until the one you want is highlighted. • Press the alphanumeric key that corresponds to the first letter of the name you wish to locate the appropriate number of times. For instance, if the name starts with "K", you would press twice for "K". The names starting with "K" will appear, with the first one highlighted. Press to scroll to the name you want.
memory. 8 The only information that can be copied from a phone book stored in the phone's memory to the one on your SIM card is a contact's name, phone number, and caller group. If a contact has more than one phone number associated with it, when that contact's data is copied from the phone to the SIM card's phone book, each phone number will be stored as separate contact. Delete: Erases the contact's data from the Phone Book. vCard: Attaches the contact's data to a message and send it to others.
• Copy to SIM (Phone): If you are currently using a phone book stored in the phone's memory, you can copy the contact's data to the phone book stored on your SIM card. Conversely, if you are currently using a phone book stored on your SIM card, you can copy the contact's data to the phone book stored in the phone's memory. • Delete: Erases the contact's data from the Phone Book. • Send: Dial the currently highlighted number.
Last Missed, Dialed, and Received Calls There are two ways you can view the last missed, dialed, and received calls on your phone, as well as information on their date and time: 1. If there have been any missed calls, the display will show a missed call message along with the number of calls that were missed. Press (View), and then press number. to scroll to the desired phone 2. In the standby mode, press to view the list of the most recent missed, dialed, and received calls. Press number.
When the number for a missed, dialed, or received call is highlighted, you can perform the following tasks: • Press to re-dial the number. • Press (Option) to bring up a pop-up menu: Call: Dial the phone number. Save (Edit): If the phone number for the call has not been stored in the Phone Book, select the Save option to create a contact for this number in the Phone Book.
Operations During a Call 8 The following options marked with an asterisk (*) are dependent on network support on may require a subscription. Adjusting the Earpiece Volume During a call, you can press the volume key on the left side of the phone to adjust call volume. Mute Press (Mute) to turn off the microphone. The person on the other end of the line will not be able to hear your voice. To restore the microphone's function, press (Unmute). Putting a Call on Hold* 1. When the only call is active: a.
Making a Second Call* Enter a phone number, or select one from the phone number or call record, and then press to dial it. The currently active call will automatically be placed on hold. However, if there is already one active call and another on hold, this action will fail. Call Waiting* If there is an incoming call while you are on the phone, a tone will sound through the earpiece and the display will show that a second call is currently waiting.
Phone Book Accesses data in the Phone Book. For details, see page 38, "Phone Book". Call Records Allows you to view information on missed, received, and dialed calls. See page 46, "Last Missed, Dialed, and Received Calls". Conference* Conference calls allow you to converse with more than one party at a time. The conference menu contains the following options: 8 The maximum number of parties that can be accommodated during a conference call depends on the particular service provided by a network vendor.
Send DTMF When the phone is connected with other devices or services, you can send DTMF (Dual Tone Modulation Frequency) strings. DTMF strings are keypad tones that can be sent via the microphone as you dial another number. Your phone will emit the tones in order to communicate with answering machines, pagers, computerized telephone services, and so forth. Enter the phone number and then press to send the DTMF string. End Call End All Ends all calls, whether active or on hold.
Calculator Allows you to use the calculator. For information about the calculator, see page 109. STK Brings up the menu for the STK (SIM Toolkit) services provided by your network vendor. Using the Silent Profile From the standby screen, you can long-press to activate the Silent profile. Once it is activated, the phone will alert you to an incoming call by vibrating with no ring tone. • When you long-press to activate the Silent profile, the phone will vibrate for one second.
Camera Function You can take photos using your phone's embedded camera, and then set photos as wallpapers for the main display's standby screen, or send them to others through MMS. 1. From the standby screen, press the view finder. (Camera), which will bring up You can also use the camera by going to the menu: Tools → / Camera. 2. Press (Option) to make the following settings for the camera: • Resolution: Sets the desired resolution for photographing.
• Face Mask: After you have selected this option, the camera's view finder will display a mask that is used to position the face of the person being photographed in good focus, in order for you to later obtain the best results when changing the person's facial expressions using the Face Morph function. See page 55 for details. To cancel the Face Mask function, press and then select Normal Preview. (Option), 3.
• Set to Wallpaper: Designates this photo as the wallpaper for the main display's standby screen. You can also do so by using the menu: Multimedia → Album, or by using Settings → Display → Wallpaper → Photo. See page 140 and page 151. • Set to Phonebook: You can use this photo as a phone book contact's visual caller ID. When there is an incoming call from that contact, the phone's display will show this photo.
a. After pressing to select the Face Morph option, the screen will show "Press number key to change," and then will bring up the original photo with the person's face remaining unchanged. At this point, you can press a corresponding number key to generate the desired facial expression effects for the person's face.
and then press to save this photo to the menu: Multimedia → Album. d. After you have saved the photo showing the expression effects you want, the original photo will reappear. Again, you can press corresponding number keys to create more photos showing various facial expressions. can also go to the menu: Multimedia → Album to / • You configure expression effects for faces shown in the saved photos. See page 140 for details.
Shortcuts Menu You can use the Shortcuts menu to assign 9 alphanumeric keys as shortcuts to commonly used functions or frequently dialed numbers. Entering the Shortcuts Menu From the standby screen, press to enter the Shortcuts menu. The numbers 1 to 9 displayed in the menu's default screen represent the corresponding 9 alphanumeric keys on the phone. Setting Function Shortcuts 1.
3. From the Add Function menu, press to select the function to be represented by the shortcut key , and then press . Alternatively, you can press a corresponding alphanumeric key to select the function you want. 8 The functions listed in the Add Function menu are selected from various other menus. For details on these functions, see page 93, "Menus". 4. After has been set as the function shortcut key, the '1' icon in the shortcut menu screen will be replaced by the icon for the function assigned to .
Setting Phone Number Shortcuts 1. The method for setting a phone number shortcut key is largely the same as for a function shortcut key. After selecting the shortcut key, press (Option) to bring up a pop-up menu. After selecting Add Phone, press to confirm. 2. From the Phone Book, select a contact, and then press . 3. Next, from the list of phone numbers for this contact, select the one that you wish to access through the shortcut key, and then press . 4.
5. Repeat the above step to add or modify a phone number shortcut. Different categories of phone numbers will be represented by different phone number shortcut icons. Using Function and Phone Number Shortcuts There are two ways to use shortcuts: 1. From the standby screen, long-press to to access the function represented by that key or dial the number it represents. 2. From the standby screen, press menu. You can then: a.
Messages Menu Besides SMS (Short Messaging Service) and EMS (Enhanced Messaging Service), your phone also supports MMS (Multimedia Messaging service). EMS allows your to insert simple graphics and ring tones in your message, while MMS enables you to send photos, colored images and music using your phone. From the standby screen, press to enter the Messages menu. You can also press when in the standby screen and then enter from the main menu by selecting .
• If there is a flashing icon on the external display, and the main display shows a red icon , this means that the SIM card's message memory is full. When the SIM card's memory is full, your phone will not be able to receive any new messages. If this has occurred, when you go to the Messages menu, the display will show a "SIM Full!" message to remind you of the current situation.
Create Short Message 1. Used to bring up the message editing screen so you can write a new SMS/EMS message. Use the alphanumeric keys to enter text. 8 For information on how to use the input methods provided by the phone for writing messages, see page 87, "Input Modes". 8 If no text has been entered in the editing screen, press to return to the standby screen; if some text has been entered, pressing will bring up the prompt "Back to Idle?", to make sure you wish to abort the message being edited.
Picture: You can select an EMS icon from the EMS icon library to insert into your message. Press you wish to insert, and then press Press to select the name of the icon (View) to view the icon. to insert the icon into your message. You can select an EMS animation from the EMS Animation: animation library to insert into your message. Press to select the name of the animation you wish to insert, and then press (View) to view the animation. Press to insert the animation into your message.
which you can edit the recipient's number will appear. There are two ways you can enter the recipient's phone number: • Key in the recipient's phone number in the number editing screen. • Before entering any phone number, you can press (Select) and then select a recipient from the list of contacts in the Phone Book. Follow the steps below: a. Press to scroll to the name of contact, and then press (Select) to select that contact. b.
• Save to Draft: Saves the message to the Drafts folder, for sending at a later time. • Edit Content: Allows you to edit the contents of the message. MMS You can edit and send MMS messages using this menu. 8 Before you start to use MMS, you have to subscribe to both GPRS and MMS services provided by your operator. Then you have to adjust MMS settings in your phone to be able to use MMS.
page. From the editing screen, press (Option), and then select Insert.
• Melody: You can select a ring tone saved in the phone to insert into an MMS page. Scroll to highlight the file name of the desired ring tone, and then press page. to insert this ring tone to the MMS 8 Each MMS page is only able to accommodate one image and one audio file. If you insert another image or audio file into the same page, the newly inserted file will replace the existing one. 8 After an audio file such as a voice memo or a ring tone is inserted into an MMS page, the icon that page.
• Remove Sound: Removes a ring tone or voice memo from the currently displayed page. • Remove Text: Deletes all of the text from the current page. • Remove Page: Deletes the current page from your MMS message. • Previous Page: Displays the previous page. • Next Page: Displays the next page. • Page Duration: This option allows you to set the length of time that each page is displayed on the screen when playing your MMS message. 6.
press (Select) to display that contact's number(s) and e- mail address(es). Press (Select) to mark the number(s) or e-mail address(es) you want, and then press to return to the list of contacts, with the selected contact's name marked as well. You can then repeat the same steps to select the other contacts' phone numbers or e-mail addresses.
Only Read: Asks the recipient to return a confirmation after reading your message. None: Cancels this function. • Priority: Determines this MMS message's priority. After you have completed all of the information and settings required for your message, pressing will send this MMS message to the designated recipients. Its backup copy will be stored in the Outbox folder as well. SIM Folder The messages in the SIM folder are the messages stored in your SIM card's memory.
• Copy All to Phone: Copies all messages to the phone's memory. 8 The messages moved to the phone will be erased from the SIM card's memory, and cannot be moved back. 8 When there is 1K or less of free space in the phone's memory, the screen will display the message "Memory Insufficient!" and you will not be able to move or copy messages from the SIM card to the phone. 8 Only complete messages can be copied to the phone's memory.
Reading an SMS/EMS message • Press (Option), which will present the following choices: Create: Allows you to write and send a new message. Delete: Deletes the selected message. Call: You can use the phone number used to send the message to call the sender. Forward: Allows you to edit the content of this message and forward it to another person. Save to Phone Book: Saves the phone number of the message's sender to the Phone Book.
• Save the phone number displayed in the message's contents. (the option for a directly displayed number). • If the message is an EMS message with an attached picture or ring tone, you can save these objects to your phone's memory (such as by selecting the option for "Picture/Animation" shown on the display). Depending on the type of the object, the phone will save it to the corresponding EMS object library in the Multimedia menu.
Forward: Allows you to edit the content of this message and forward it to another person. Save to Phone Book: Saves the phone number of the message's sender to the Phone Book. For information on how to save, see page 38, "Adding Contacts to the Phone Book". Delete All: Deletes all the messages in the inbox. • Press to play the message's pages in sequence. While playing, you can perform the following tasks: a. When playing the message, you can press (Pause) to temporarily stop playing the message.
Call: Uses the number from which the message was sent to call the sender (listed in the "Sender" item on the display), or dial a phone number shown in the contents of the message (the displayed number option). Scroll to the desired number, and then press to dial the number. Forward: Lets you edit the message's contents, and then forward it to another person. Details: Allows you to view the date and time when the message was sent.
Save All: Saves all the objects attached to the message. Template SMS Template You can use the quick message templates in this menu to compose a message without having to enter the entire text character by character. You can use the factory default templates, or templates that you previously saved to the list. Scroll to the desired template and then press to enter its text into your message. You can then edit the text as you wish and then send the message.
Forward: Allows you to edit and forward the message to other recipients. Deletes the message. Delete All: Deletes all the messages in the Outbox. Delete: • Press to read the message. After reading the message, you can press (Option) to execute the following options: Resend: Allows you to edit and send the message to its original recipients. Forward: Allows you to edit and forward the message to other recipients. Delete: Deletes the message.
Voicemail Used to dial the voicemail number provided by your network vendor to listen to your voicemails. 8 Your network vendor will provide you with your voicemail inbox number and a number for accessing any other voicemail services. For detailed information about voicemail services, contact your network operator to see if you need to save a specific phone number to your phone in order to access your voicemail inbox.
Bearer Mode This can be set according to whether you are using a GPRS network system or a regular GSM dialup network. If you are using a GPRS network, you can use both the GPRS and dialup network to send and receive SMS messages. If however you are using a dialup network, you are restricted to using only the dialup network for sending and receiving SMS messages. • GPRS: Use only the GPRS network to send and receive SMS messages. • CSD: Use only the dialup network to send and receive SMS messages.
Direct Reply You can request that your reply to an SMS be sent directly through the sender's message center. MMS Settings Filter Your phone will reject all MMS messages from the senders listed here. Expiry Sets the length of time your outgoing MMS message stays on the server before it reaches the recipient successfully. Reply Type You can determine here whether you want to use an SMS message or MMS message in reply to an MMS message you have received.
Deferred Download After you activate this function, the phone will only download the information associated with the sender when it receives an MMS message. You can then decide whether to download this message's content after you have read the information related to the sender. Delivery Report Asks the recipient to return a confirmation after receiving your MMS message. Read Report Asks the recipient to return a confirmation after reading your message.
Broadcast Cell broadcast messages are general messages that your network operator broadcasts to all phones within a particular area. These messages are broadcast in numbered channels. For example, channel 030 might be for local weather, 060 for traffic reports, 080 for information about local hospitals, taxis, pharmacies, and so forth. You can receive cell broadcast messages that your network operator broadcasts, and select your preferred topics and languages.
possible range is 0 to 65534. You are no longer limited to selecting only single channels, but can specify a range. After the list has stored the topic range, you can select a specific topic and then press (Option) to add it to the list. You can also edit or delete selected topics. Language You can limit the cell broadcast information that you receive from your network operator to a specific language. Press press (Select) to select your preferred language, and then .
Voice Memo 1. When the phone is in the standby mode, long-press 2. Press (Option) to bring up a pop-up menu. Select Add and then press . The voice memo screen will appear. Use to navigate to the button icons on the screen and access Voice Memo functions: a. Press to record. b. Press to stop recording. c. Press to play the voice memo. 3. After you are finished recording, press (Save) to save the voice memo. Enter the name of the recording and then press . 4.
b. Press to play the voice memo. In the voice memo screen, you can press play the previous or next memo. to Input Modes Changing the Text Input Mode When the display shows the editing screen, you The text input mode will be able to see the name of the current text currently in use input mode in the upper right corner of the screen. Press to change the input mode.
Letter Input Mode (ABC) In this mode, press the key containing the desired letter repeatedly to scroll through the available characters in order until it is reached. How to use the letter input mode • You must press the key corresponding to the desired letter the correct number of times in order to enter the letter you want. Display letters for entry according to the order shown on each key.
How to use iTap • Press once the alphanumeric key corresponding to the first letter of the word you wish to enter without considering where that letter falls in the sequence of characters available through that key. Then press the key corresponding to the second letter, and so forth. The phone will predict which word you wish to enter based on the set of keys you have pressed. The predicted word will be shown in the lower left portion of the screen.
inserted after "COME". 4. Press to enter "HOME". 5. Since "GOOD" is not the word that you wish to enter, press display the next candidate word, "HOME". 6. Press to to place "HOME" into the message. Symbol Input Mode When editing messages, press bottom of the screen. Use to open the symbols field along the to move the selection box to the symbol you wish to enter, and then press 90 Using Your Phone to place it in the message text.
Direct Connection to URLs Your phone provides handy preset URL text hotkeys, enabling you to enter a complete URL more quickly and conveniently, and making Internet access more efficient and enjoyable. From the standby screen, you can rapidly key in numerical URLs. If, for example, you wish to enter "http://123.com" you need only key in "123" and then press . The full URL will appear on the screen. automatically adds the necessary "http://" prefix and the ".com" domain suffix.
• After you press to enter "http://" press to enter "/" and "-". For example, if after you enter "123" and then press once-causing "http://123.com" to appear on the screen-you press again, the URL will change to "http://123.com/". Pressing switch between "/" and "-". again will • When the screen shows the desired URL, press Internet and access this URL address.
Menus The phone's menus provide various features. The main menu consists of 9 icons. Each icon represents a particular menu item, which is used to access related sub-menus. For information about navigating menus, see page 23, "Menu Navigation". Phone Book This menu provides various functions for managing the Phone Book, including the ability to add, locate, and copy contact data; add contacts to a caller group; and so forth. Find Used to locate a contact in the Phone Book.
Copy If you are using the phone book stored in the phone's memory, you can copy contact data to the SIM card's phone book, and vice versa. You can select a contact to copy from one phone book to the other, and copy all contacts in one phone book to the other by choosing the option Copy All Phone Book to SIM (Copy All SIM Phone Book to Phone). Delete Deletes a contact from the Phone Book. You can delete one contact at a time, or delete all contacts at once.
Add: Add a contact to the caller group. Press to select a contact to add, and when finished press . Deletes the selected contact from the contact group.
Privacy Manager This option allows you to set your phone to reject certain calls, or alternatively, specify which calls to accept, rejecting all others. 1. First, create a list of calls that you wish to accept (Accept List) or a list of calls that you wish to reject (Reject List), by scrolling to the corresponding item. Then press (Edit) and the names of the contacts who are already on the selected list will be displayed.
If you choose to activate the Accept List, from now on your phone will only be able to receive calls from contacts in the Accept List. If, on the other hand, you choose to activate the Reject List, your phone will not be able to receive calls from contacts in the Reject List. 8 The same contact cannot be included in both the Accept List and the Reject List. 8 If you are currently using the phone book on your SIM card, you will not have access to the Privacy Manager feature.
Activate Used to activate the phone book stored in the phone's memory or on your SIM card. Press to highlight the desired phone book and then press . My Number This option allows you to save your SIM card number and name to your SIM card's memory. Press (Option) and select Add. Now select whether you want to enter your name or number and then press (Edit) or to begin entering the information.
Call Records 8 Your network operator must support this feature in order for you to be able to use it. This menu includes a list of your missed calls, dialed calls, and received calls. Call costs and time are also recorded. Missed Calls Shows your most recent missed calls. Press to scroll to the missed call that you wish to select. You can now choose to view, edit, or delete the number for the missed call. The procedure is the same as that described on page 46, "Last Missed, Dialed, and Received Calls".
Call Duration 8 This feature is only accessible if supported by your network operator. Last Call Time Shows the duration of the last call. All Calls Time Shows the total time for all calls. Received Calls Time Shows the total time for all received calls. Dialed Calls Time Shows the total time for all dialed calls. Clear Clears all call time records. 8 You must enter your PIN2 code in order to zero call times. is a PIN2 code? / What • The PIN2 is the second PIN code.
Call Cost Last Call Cost Shows the cost of your last call. 8 Requires the support of the network operator. All Calls Cost Shows the total cost of all calls. 8 Requires the support of the network operator. Clear Clears all call cost records. 8 Requires entry of the PIN2 code. Call Cost Limit Shows the current limit set for total call costs. Set Cost Limit Allows you to set a limit for total call costs. If call costs exceed this limit, the phone will no longer be able to dial pay calls.
Messages For a description of the features available in the messages menu, see page 62, "Messages Menu".
Organizer Calendar You can use the Calendar to set up memos for forthcoming events such as a meeting, an appointment, or a friend's birthday. The Calendar will also remind you about events you have previously scheduled. 1. When you open the Calendar, the phone will show the calendar for the current date. 8 If you have not set the current date on your phone, go the menu Settings → Date & Time. See page 145. In the Calendar screen, press to move the red box to the date where you wish create a memo.
begin entering data. You can enter data in these fields: Change the memo's assigned date. In the Calendar screen, press to scroll to the date where you wish to create the memo, and then press . Enter a time for the event associated with the memo by using the appropriate number keys. Enter a name for the event associated with the memo. Enter the scheduled location for the event associated with the memo. Enter the names of the participants in the event associated with the memo.
name. 5. You can now perform the following tasks: a. Press (Option) to select whether to edit or delete the memo, or send this memo to others through SMS. b. Press to view the information in the memo. Then press (Option) to edit or delete the memo c. Press (Back) to return to the Calendar screen. You can move the red box to other dates to create additional memos (dates that already contain memos will be marked by a yellow box); you can also create a second memo for the same date.
completed, you can scroll to the item and then press to mark it to remind yourself that the task has been done. If you press (Option), you can activate the Auto Delete, which will automatically clear any to do items that you have marked as completed. Note You can use this feature to create a list of notes. 1. Press (Option) and select Add to bring up the editor screen. Enter the desired text and press . 2. A message on the screen will ask whether you wish to add a password for this note.
Alarm Clock If you activate the Alarm Clock feature, when the specified date and / time arrive, the phone will sound the alarm, even if your phone is turned off. Use the following steps to set an alarm: 1. Select an alarm you wish to set and activate. 2. Press to select the feature for activation. The configuration fields for the alarm will appear in the lower part of the screen. Day Used to set the alarm to go off on a particular day from Monday to Sunday. Press (Edit) to display the days of the week.
Time Duration Allows you to set the length of the alarm. Press desired alarm duration and then press (Edit) to select the . 3. Lastly, you must press to save all your current Alarm Clock settings. After completing Alarm Clock settings, will appear in the external display's status bar; status bar. will appear in the main display's the alarm rings, there are two ways to turn it off: / When • Press (Snooze) to stop the alarm. The alarm will ring again five minutes later. • Press to turn off the alarm.
Calculator Allows you to use the phone as a calculator. Use to perform the mathematical operations shown on the screen. 8 You can enter numbers up Entered numbers and calculation results will appear in this field. Press to enter a decimal point. to a maximum of 8 digits in length.
2. Used to set the exchange rate. Press (Option) and select Rate Setting, then enter the rate for converting from Currency 1 to Currency 2. The conversion calculation result will be displayed in the same line as the bottom currency on the screen. Use the to view the calculation result. The calculation can provide precision up to two decimal places. 8 The exchange rate field can accommodate a maximum of five digits (including decimal digits). 8 Press to enter a decimal point. 3.
Stopwatch 1. Press to start the stopwatch. 2. While the stopwatch is running, you can press (Split) to save up four elapsed times (such as in a race). The display will show the saved times in the lower part of the screen. 8 Pressing (Back) while the stopwatch is running will bring up the "Quit?" warning message (the stopwatch will continue to run). Press stop the stopwatch or screen. 3. Press (Yes) to (No) to return to the timer to halt the stopwatch. 4.
timer will stop and return to the timer screen. If you press (No), you will exit the countdown timer screen, but the countdown timer will continue the countdown. You can then perform other tasks, and when the countdown is finished, the "Time's Up" message will appear and an alert sound will be played. Press (Exit) to exit the screen. Memory Status Shows the amount of memory, including space for storing pictures, animations, and ring tones on the phone.
Games Your phone provides a number of exciting games that you can use to entertain yourself when you have a spare moment. Champion Soccer This game lets you manage one of the world's top eight soccer teams in its quest to win the greatest prize in world soccer. 1. After choosing this option, select Start to enter the game's opening screen. Press START to begin a new round of play. and select 2. Select World Cup Mode or Arcade Mode.
3. In the World Cup Mode, you can select your own team with the opposing team selected at random by the phone. If your team wins, you face the next team as you make a challenge for the World Cup title. In the Arcade Mode, you can select your own team and the opposing team to play a single game. Press to select a flag representing a national team, and then press to confirm. 4. After the message announcing the first half appears, press 114 Menus to begin the game.
Game Controls •When attacking, use •When on defense, use these three keys to select which player to pass the ball to. these three keys to select players to move. •Controls the direction of the player's movement. •When attacking, •When on defense, press to take a shot on goal. press to tackle. During the game, you need to control your three players on the pitch, while your goalkeeper is controlled by the phone.
Game screen The opposing team The opposing team's score Your team Your score The number of the player you are controlling. Timer Full pitch view White point: The position of the player you are controlling Black point: The ball's location Blue points: Your teammates Red points: Players on the opposing team. Game options • START: Begins a new game. • Continue: Resumes an interrupted game. Usable only in the World Cup Mode. • Controls: Brings up an explanation of how to use keys during a game.
• Exit: Quits this game.
Dragon Fight The flying dragon that you control must make incursions into hostile territory and destroy enemies. Select Start to enter the game's opening screen, and then press to begin play. The more enemies you destroy, the higher your score. If you collide into an enemy, you lose one flying dragon.
Internet Your phone includes a built-in WAP browser, allowing you to use the phone for mobile Internet connectivity. You can browse the online services offered by the network operator or ISP, such as information on financial news, sports, travel, and entertainment. To use the phone to get online, necessary WAP and GPRS settings must be made in this menu.
Start Browser Starts up the browser and connects to the homepage. Browsing a webpage Referring to the soft key commands at the bottom of the screen, press and to perform needed tasks while browsing a webpage. Press to scroll up or down a webpage. For details on browsing a webpage, inquire with the network operator providing WAP services. Your Internet connectivity service will determine the layout and content of the webpages you view.
Home Returns to the home page. To designate a particular page to be your home page, go to 9 Settings → 1 Homepage. Exit Closes the browser and returns you to the main menu screen. Inbox When your phone receives a message that can only be viewed using a WAP browser, you enter this WAP inbox to read the message. Bookmarks You can open the Bookmarks menu and select webpage bookmarks. View Allows you to see the current bookmarks and bookmarks folders.
Move to Folder: Moves a bookmark to the designated folder. Delete All: Deletes all bookmarks and book-marks folders. Hotkeys: Allows you set a numerical key as a hotkey for a bookmark. After completing the setting, you can press this numerical key to directly link to the webpage represented by the bookmark. Mark Site Adds the current webpage to your bookmarks list.
Homepage Designates a homepage. When you start up the WAP browser or if you select Home from the browser's menu, the screen will display the homepage you designate. a. Press (Edit) and then enter the URL of the webpage that you wish to use as your homepage. (Some WAP service providers do not allow users to set a homepage.) b. Select the Save option to designate the URL you entered as your homepage. Select Use Default to use the homepage designated by your WAP service provider.
Set Proxy Your phone can save the settings for six WAP proxy servers. You can select one of these proxy settings for use as a default so that your phone will connect to that proxy server when you begin an Internet session. You can also go to the menu Internet → Wap Service → Wap Settings to select the server that you wish to activate. See page 126. Circuit Prompt The Circuit Prompt is a message displayed before each circuit data call is made. It reads, "Circuit is down.
Authentication You can decide whether your phone should store your user name and passwords for websites that require them. If you allow your phone to authenticate you automatically, you will not need to re-enter your user name and password each time you visit the same website. Advanced Restart Browser Restarts the browser, and automatically returns to the designated homepage.
WAP Message Starts up the browser and displays the WAP inbox so you can read WAP messages. Enter Address Starts up the browser and connects to the URL you enter. Resume Returns to the last webpage you viewed. Clear Cache Clears webpage content that the browser temporarily stores in memory. WAP Settings In this menu, you can make settings for the WAP servers of six different network operators, and select the server that you would like to use when connecting to the Internet.
By scrolling to a particular group of WAP server settings that you wish to modify, and then pressing (Option), you can create a new group of settings, edit the settings, or delete the settings. WAP server settings include the fields listed below. Press (Edit) to edit the setting in each field. When you are finished with the settings for all fields, you must press in order for this group of WAP server settings to be saved. • Profile Name: Gives the WAP server settings a name.
CSD/GPRS: Use the dialup network preferentially. Only if there is no dialup network will the GPRS network be used. CSD: Use only the dialup network. network is a GSM Circuit Switch Data Service (CSD / Afordialup short). Using a dialup network can be likened to using a home computer's modem, in that before connecting to the Internet a number must be dialed. As for GPRS, it like the LANs used at company, where users do not need to dial a number to access the network.
Line Type: This is the type of dialup connection. Press to select. Baud Rate: The default value is 9600, which is the standard speed for data connections with a GSM mobile phone. Auth Type: This is information needed for telecommunications protocol authentication.
JAVA Your phone provides Java support, allowing you to download and install Java applications that you like, such as various Java games, from sites provided by your network operator. You can then run these Java applications directly on your phone. If you do not need an application, you can remove it from your phone at any time, replacing it with another downloaded application. The JAVA menu contains the following items: Application Browser All Java applications will be listed in this menu.
• Network Access: Some types of Java games are only playable online (for example, mahjong), and using the phone to go online entails an extra cost. However, it may not be possible to determine from a game's name alone whether or not it is an online game. Therefore, this setting allows you to be presented a prompt asking if you wish to go online to play a game before actually running the program.
Application Browser and terminate the Internet connection. After installation is complete, you can enter a new URL to download a Java application from another site. 3. In addition, you can also use the WAP browser to download Java applications. The browser screen will first display information about the applications. After you have read this information, you can run the download command shown on the screen to begin downloading the desired application to the MyApps group on the phone.
Move: Removes the Java application from the MyApps group and places it in another group in the Applications Browser. Scroll to the group where you wish to move the application and then press . 8 To move a Java application to a group other than MyApps when it is currently the only group, you must press (Option) in the JAVA → Applications Browser menu and select New to create a new group. • Press to show the names of the executable files of the applications.
Multimedia Picture This image library stores the phone's default pictures, as well as images received in EMS messages, or downloaded through WAP services or using multimedia communications tools. The file formats supported by the phone are BMP, PNG, GIF, JPEG (progressive or marithmetic-encoded saves not supported), and EMS picture. Scroll to the desired picture to access the following options: • Press to display this picture.
Set Wallpaper: Use the picture as the wallpaper for the standby screen. Animation This animation library stores the phone's default animations, as well as animations received in EMS messages, or downloaded through WAP services or using multimedia communications tools. The procedure for using this menu is the same as that described above for the Picture menu. The phone supports the following animation file formats: GIF, EMS animation.
8 Ring tones that support the EMS format (such as Chimes High) cannot be set as the phone's alert sound for incoming calls, so they do not offer this menu option. • Rename: Allows you to give a new name to the ring tone. 8 The phone's default ring tones cannot be renamed, so they do not present this option. • Edit: Allows you to edit the ring tone. 8 The phone's default ring tone cannot be edited, and only Composer offers this option.
Composer You can edit your own polyphonic ring tone melodies, and use them as alert sounds for incoming calls. A polyphonic ring tone consists of musical tones in multiple channels. The Composer function allows you to create a maximum of 8 channels, mixing them to create the final polyphonic ring tone. Note format Length Octave Pitch Sharp Entering default notes Press to to enter the eight pitches in an octave as quarter notes: Do Re Mi Fa So La Ti.
Adjusting the length of a note The default note length is a quarter note (the screen uses the number 4 to represent a quarter note). Press to increase the note's length (the number on the screen will increase); press to reduce the note's length (the number on the screen will decrease).
Steps for creating a polyphonic ring tone 1. The first time you enter the Composer menu, you will see 8 channels that you can select for editing. Each channel can be used to save one passage of music that you have created. Scroll to the channel that you wish to edit, and then press to enter the ring tone editing window to begin composing the music for this channel. 2. Edit notes according to the procedures described above.
• Play All: Plays the polyphonic ring tone that results from mixing all channels. • Play Channel: Plays the channel you have currently scrolled to (if this channel does not contain any music that you created, this option will not appear). • Save: Select this option and your phone will automatically mix the music you have created in the channels into a polyphonic ring tone, and save this ring tone to the menu Multimedia → Melody → My Melodies. Press and enter a name for the ring tone and it will be saved.
1. Press to scroll to the photo thumbnail you need. 2. Press to display the photo in full screen. Press next/previous photo. to show the 3. When the display shows photo thumbnails, or after you press to display a photo in full screen, you can press (Option) to perform the following tasks with that photo: • Send Photo: This option enables you to send the selected photo to others through MMS. You can also do so by selecting the menu: Messages → Create → MMS.
• Delete: Deletes the selected photo. • Delete all: Deletes all of the photos stored in the Album menu. （this option is only available when the screen shows photo thumbnails). • Face Morph: You are able to change a person's facial expression shown in the photo with this Face Morph function, and then save photos showing different expressions of that person. Follw the steps below to perform the Face Morph function: a.
c. To reset a red spot's position, press (Undo) to first remove that spot, press to display it again in its default position, and then press to adjust its position. 8 The moment you finish setting the four spots' positions and press , you can immediately press all of the spots' positions. (Reset) to reset d. When the spots are in desired positions, press . The screen will show "Press number key to change," and then will bring up the original photo with that person's face remaining unchanged.
e. Press to intensify/reduce expression effects. Intensity levels will be displayed at the top right corner of the screen ranging from 1 to 5; the default value is 2. f. When the photo shows desired expression effects, you can press and save this new photo as a separate file. Enter this new photo's file name, and then press to save it to the Album menu. g. After you have saved the photo showing the expression effects you want, the original photo will reappear.
Settings Date & Time Used to set the time and date, as well as the format in which the time and date will be displayed on the startup screen. Time 1. Press to select either the Auto or Set mode for this item: Auto: Automatic time zone adjustment. If during travel, you move between time zones, the phone will automatically adjust the time displayed on the screen based on the time zone prompts provided by the local network operator so that you always have access to accurate local time.
Secondary Time Allows you to display the time in another designated time zone. If you choose to activate this option, the standby screen will display the time in that time zone along with your local time. Time in secondary time zone Power On/Off Allows you turn the phone on and off at specified times to conserve power. When riding in an airplane or in any other situation where you cannot use a mobile phone, remember to deactivate the Power On/Off option.
Profiles A profile is a group of settings that determine whether the phone will alert you to incoming calls through a ring tone or a vibrating alert, and how ring tones in general are used on the phone. These settings allow the phone's operation to best suit the environment you are in. 1. Press to scroll to the desired profile and then press to activate this profile. You can choose from among the following profiles: Normal This is the default profile.
Handsfree This profile is only active when a hands-free kit is attached to the phone. Once this profile is activated, the main display's status bar will show the show the icon; the external display will icon. Airplane When you are on a plane, you can select this profile to turn off the phone. Once this profile is activated, the phone will automatically be powered off, and all alarms will be suspended. If the phone is turned off by long-pressing still turn the phone at the appointed times.
particular environment. 8 After entering the Edit menu, the setting for each option will be displayed, providing a overview of the profile. Vibrate Includes the following setting options: • Ring Only: When there is an incoming call, the phone will use a ring tone but no vibrating alert. • Vibrate Only: When there is an incoming call, the phone will use a vibrating alert but no ring tone. • Ring & Vibrate: When there is an incoming call, the phone will use both a vibrating alert and a ring tone.
Ring Volume Press to adjust the ring tone volume or mute the ring tone. Answer Mode • Send Key: Allows incoming calls to be answered only by pressing . • Any Key: Allows any key except to be used to answer an incoming call. In this mode, is used to reject an incoming call, and not to answer. • Automatic: If the Automatic answer mode is activated, the phone will ring for five seconds, and then the incoming call will be automatically answered (only the Handsfree profile allows this setting).
Display Theme A display theme consists of a combination of display color and the standby screen wallpaper. Different display colors are paired with different preset wallpapers, so when you change the display color, the standby screen wallpaper will also change. Scroll to the color that you wish to use and then press (View) to preview the color matched with the standby screen wallpaper. Press the setting.
Photo: Here you can select a photo saved in the phone memory as the wallpaper. can also use this feature to change the wallpaper matched / You with a color in the Theme option. Welcome Message Used to select and configure the animation/picture/text that is displayed when the phone is turned on, as well as the music that is played. • Animation: Only the animation selected in this option will be displayed when the phone is turned on.
Contrast Press to adjust the contrast of the screen's display. Press to confirm the setting. Brightness Press to adjust the brightness of the phone's display backlighting. Press to confirm the setting. Backlight Setting You can turn the phone's keypad backlighting and display backlighting on or off, as well as set the length of time that backlighting will remain activated after the flip is opened or a key is pressed.
• Always On: The external display will remain on, cycling continuously through displays of the time and animations. Because the S670C's external display drains power from the battery when it is on, selecting Cycle or Always On will reduce battery life. OLED Animation Setting You can set the animations to show on the external display. Press (Select) to make your selections; press (Cancel) to clear the animations that you have selected. When you are finished, press to confirm your selections.
Call Settings Call Divert 8 Requires the support of the network operator. Forward All Forwards all incoming calls to a designated phone number or voicemail inbox. When you use this feature, you must enter a phone number to which to forward incoming calls. 8 After the Forward All mode is activated, the standby screen will display the icon. When Busy The phone will divert incoming calls to another number when you are in the middle of another call.
Call Barring You can request that your network operator block the dialing or receiving of certain calls. The call barring services below require the support of your network operator. To activate or cancel any of the options below, you must enter the network password provided by the network operator. All Outgoing Blocks dialing of any calls from the phone. Intl. Out If this option is activated, no international calls can be made with your phone. Intl.
Call Waiting If there is an incoming call when you are in the middle of another call, the screen will display the number of the incoming call and call waiting message to alert you. You can activate, cancel, or view the status of this feature from this menu. 8 You must apply to the network operator for the call waiting service in order to use this feature. Auto Redial If there is no answer at a number you have dialed, the phone will automatically redial.
Fixed Dial Number After this feature is activated, the phone will only be able to dial numbers on the Fixed Dial Number list. If a number is not on the list, calls cannot be made to this number. 8 When you activate or cancel this feature, you must enter the PIN2 code. , If the PIN2 code is entered incorrectly three consecutive times, the PIN2 code will be locked down. You will need the PUK2 code to unlock the PIN2 code. Contact your network operator to obtain the PUK2 code.
Minute Beep Once this option is activated, the phone will emit a beep once every minute during a call. Network Generally speaking, the choice of the network that your phone uses is configured automatically. When turned on, the phone will automatically connect to the network provided by your network operator, or will automatically connect to the roaming network when you are outside the coverage of your regular network.
Band Setting According to your requirements, you can set an appropriate band in the GSM network system. Connection Mode Used to set whether the phone will also search for a GPRS network when it is turned on. • GPRS & GSM: When it is turned on, the phone will search for available GPRS and GSM networks. • GSM Only: When it is turned on, the phone will search only for a GSM network. Security You can use a PIN code, phone password, and SIM card lock authentication to prevent unauthorized use of the phone.
If you wish to change the PIN1 code, you must press in the Enable item to select On, so that you will be able to enter and confirm the new password. PIN2 Code Used to change the PIN2 code. The procedure is the same as for the PIN1 code. Phone Lock Activates/deactivates or changes the phone's startup password. The startup password prevents unauthorized persons from using your phone.
password. If the password is entered correctly, the phone will be able to recognize the new SIM card and use it normally. The next time the phone is turned on with this SIM card inserted, the phone will not ask again for you to enter the SIM Lock password. 8 Your phone can recognize a maximum of three different SIM cards. Before setting the SIM Lock feature, you must enter the previously set SIM Lock password (the default SIM Lock password is 1234). The password must be between 4 and 8 digits in length.
4. After completing settings, press . The phone will prompt you to enter and confirm the Screen Lock password. You have two choices: a. If you do not wish to change the password, press to activate the Screen Lock feature using the previously set password. b. If you wish to change the password, enter the new password in the New Password and Confirm fields, then press to use the new password and activate the Screen Lock feature.
Outside Access When the User Group service is activated, enabling Outside Access will allow users in the group to make calls to numbers outside the group. However, incoming calls will still be restricted to calls from within the group. Restore Restores all of the phone's settings to their factory defaults.
Care and Maintenance Take note of the points noted below to ensure that you are using the phone properly and to extend the lifespan of the phone. • Store the phone and its accessories out of the reach of children. • Keep the phone and accessories dry, and use the phone in environments where the temperature is between – 20°C and 55°C. High or low temperatures outside this range may damage the phone. • If possible, do not use or store the phone in excessively dusty or dirty environments.
Troubleshooting If you encounter problems while using the phone, or if it performs erratically, you can consult the information in the chart below. If your particular problem cannot be resolved using the information in the chart, contact the dealer where you purchased the phone. Problem Possible cause Solution • The network signal is too Move to a location where the weak at your current network signal can location — for example, in properly received.
Problem Possible cause • The standby time is related to your network operator's system configuration. The same phone used with different network operators' systems will not provide exactly the same length of standby time. Shortened standby time • The battery is depleted. In Use a new battery. high-temperature environments, battery life will be shortened. • If you are not able to connect to the network, the phone will continue to send out signals as it attempts to locate a base station.
Problem Possible cause • SIM card invalid. Unable to connect to the network. You cannot answer incoming calls. Solution Contact your network operator. • You are not within the Check the service area with network's service area. your network operator. • Poor signal. Move to an open space, or if you are inside a building, move closer to a window. • You have activated Go to the menu Phone Book → Privacy Manager and then select Off in order to deactivate this option.
Problem Possible cause • The battery or battery Solution Contact the dealer. charger is damaged. Battery will not charge. • The phone's temperature Adjust the battery charging is below 0 °C or higher environment to avoid extremes of temperature. than 45°C. • Poor contact between the Check all connectors to battery and charger. Unable to enter information into the Phone Book. Unable to select certain features. • The Phone Book's memory is already full.
170 Troubleshooting
