User Manual

15
Get Functi on Len Cm
d
Typ
e
Cmd
Code
(Hex)
RS232
Send Get Command
MDA to Device
System Reply
Command message
On/Off Timer 14 g E0 Input value: Byte1 - Byte2 - Byte3…Byte9
(1) Byte1[3:0]: The Number of the On/Off Timer. There are totally 7 On/Off Timers, and this byte is used to selected which timer is going to be accessed.
(2) Byte1[7:4] is reserved, should be 0.
(3) Byte2~9 are reserverd, should be 0x00.
Return value: Byte1 - Byte2 - Byte3…Byte9
(1) Byte1[3:0]: Should retuen the same value as Byte1 at Input value.
Byte1[7]: Reserved, should be 0.
Byte1[6]: The Timer is enable or not. Byte1[6]=1 means enable.
Byte1[5]: The On Timer is enable or not. Byte1[5]=1 means enable.
Byte1[4]: The Off Timer is enable or not. Byte1[4]=1 means enable.
(2) Byte2: The Day of the On/Off Timer. bit0 for Sunday, bit1 for Monday, bit2 for Tuesday, bit3 for Wednesday, bit4 for Thursday, bit5 for Friday, bit6 for
Saturday, bit7 for Everday.
(3) Byte3: The Hour of the On Timer. Byte3=0x00~0x17.
(4) Byte4: The Minute of the On Timer. Byte4=0x00~0x3B.
(5) Byte5: The Hour of the Off Timer. Byte5=0x00~0x17.
(6) Byte6: The Minute of the Off Timer. Byte6=0x00~0x3B.
(7) Byte7: Select the Video Source.
0x00=VGA, 0x01=HDMI1, 0x02=HDMI2, 0x03=AV, 0x04=YPbPr,
0x05=S-Video, 0x06=DVI, 0x07=DisplayPort, 0x08=SDI, 0x09=Multi-Media.
0x0A=Network, 0x0B=USB Display
0xFF=Default. Other values are reserved.
(8) Byte8~9 are reserved, and should be 0x00.
Input Value: Byte1 - Byte2 - Byte3…Byt e9
(1) Byte1=0x00: IP Setup Mode
Byte1=0x01: IP Address
Byte1=0x02: Get Subnet Mask
Byte1=0x03: Default Gateway
Byte1=0x04: Primary DNS
Byte1=0x05: Secondary DNS
Byte1=0x06: MAC Address
(2) Byte2~9 are reserved, should be 0x00.
Return value: Byte1 - Byte2 - Byte3…Byte9
The Byte1 at the return value should be the same as the value of Byte1 at Input value. Byte2~Byte15 should be hex value format
(1) If Byte1=0x00(IP Setup Mode) at Input value, the return value should be
Byte1=0x00
Byte2=0x00: Manual
0x01: DHCP
Byte3~9 are reserved, should be 0x00.
(2) If Byte1=0x01(IP Address) at Input value, the return value should be
Ex: IP address=169.254.81.38
Byte1=0x01 (same as Byte1 at Input value)
Byte2=0xA9 (=169), Byte3=0xFE (=254), Byte4=0x51(=81), Byte5=0x26 (=38)
Byte6~9 are reserved, should be 0x00.
(3) If Byte1=0x02~0x05 at Input value, refer to (2)
(4) If Byte1=0x06(MAC Address) at Input value, the return value should be
Ex: MAC address=00:22:64:7E:2C:82
Byte1=0x06 (same as Byte1 at Input value)
Byte2=0x00, Byte3=0x22, Byte4=0x64, Byte5=0x7E, Byte6=0x2C, Byte7=0x82
Byte8~9 are reserved, should be 0x00.
E1g14Network Setting