MP626/MP670 Digital Projector User Manual Welcome
English Table of contents Important safety instructions .......................3 Introduction......................7 Projector features ................................. 7 Shipping contents................................. 8 Projector exterior view......................... 9 Controls and functions ....................... 10 Positioning your projector .14 Choosing a location............................ 14 Obtaining a preferred projected image size .....................................................
English Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation.
English Safety Instructions (Continued) 4 7. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. 10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage. 8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions. 11.
English Safety Instructions (Continued) 13. Do not place this projector in any of the following environments. 14. Do not block the ventilation holes. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. - Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.
English Safety Instructions (Continued) 17. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury. 18. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced. 19.
English Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.
English Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories S LT C R 20 25 O The supplied accessories will be suitable for your region, and may differ from those illustrated.
Front/upper side 4 1 1. 2. 3. 4. 5. 6. 7. Front IR remote sensor Quick-release button Projection lens External control panel (See "Projector" on page 10 for details.) Vent (cool air intake) Audio speaker Focus ring and Zoom ring 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25.
English Controls and functions Projector 8 1 9 2 3 10 POWER TEMP 4 LAMP 6. 7. 11 12 13 8. 5 14 6 7 1. 2. 3. 4. 5. 10 9. POWER indicator light Lights up or flashes when the projector is under operation. See "Indicators" on page 64 for details. MENU/EXIT Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings. See "Using the menus" on page 26 for details. Left/ Starts the FAQ function. See "Utilizing FAQ function" on page 42 for details.
6. 1 2 10 3 7. 11 4 12 5 13 6 4 14 7 8 15 9 16 8. 9. 1. IR transmitter Tranmits signal to projector. 2. POWER Toggles the projector between standby mode and on. See "Starting up the projector" on page 25 and "Shutting down the projector" on page 49 for details. Menu/Exit Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings. 11. See "Using the menus" on page 26 for details. 3. 10. 4. 5. Freeze/unfreezes the video.
English 13. / 15. Right cursor: Navigates and changes settings in the OSD. See "Using the menus" on page 26 16. for details. 14. : Activates panel key lock. See "Locking control keys" on page 42 for details. When the On-Screen Display (OSD) menu is activated, the #5, #7, #10, and #13 keys are used as directional arrows to select the desired menu items and to make adjustments. See "Using the menus" on page 26 for details. Source Displays the source selection bar.
Replacing the remote control battery 2. English 1. Press the release in the direction of the arrow. Remove the battery by pulling the tray out in the direction of the arrow. 2 1 Insert the supplied batteries taking note of the polarity (+/-) as shown here. TS C R 20 25 O L 3. 3V 4. Replace the tray. S C R 02 52 T L O V 3 M • Before using the remote control for the first time, remove the transparent insulation tape. • Avoid excessive heat and humidity.
English Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1.
English Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. 4:3 is the native aspect ratio of MP626 and MP670. To be able to project a complete 16:9 (widescreen) aspect ratio image on MP626 or MP670, the projector can resize and scale a widescreen image to the projector's native aspect width.
English How to determine the position of the projector for a given screen size 1. 2. Select your screen size. Refer to the table and find the closest match to your screen size in the left columns labelled "4:3 screen". Using this value, look across this row to the right to find the corresponding average distance from screen value in the column labelled "Average". This is the projection distance. 3. On that same row, look across to the right column and make note of the "Vertical offset in mm" value.
English MP626/670 projection dimensions Refer to "Dimensions" on page 67 for the center of lens dimensions of this projector before calculating the appropriate position. Maximum zoom Minimum zoom Screen Center of lens Vertical offset Recommended projection distance from screen in mm 4:3 screen diagonal Projection distance Width Height Min length Average Max length Vertical offset in mm (with min. Inches mm mm mm (with max.
English Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.
English Connecting a monitor If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the D-SUB OUT signal output socket on the projector to an external monitor with a VGA or VGA to DVI-A cable by following the instructions below. To connect the projector to a monitor: • With a VGA cable: • With a VGA to DVI-A cable: Your monitor must be equipped with a DVI input socket. 1. 2. 3.
English Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
English Connecting HDMI source devices The projector provides a HDMI input socket that allows you to connect it to a HDMI source device like a DVD player, a DTV tuner or a display. HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays over a single cable. It provides pure digital viewing and listening experience.
English Connecting Component Video source devices Examine your Video source device to determine if it has a set of unused Component Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. 2.
English Connecting S-Video source devices Examine your Video source device to determine if it has an unused S-Video output socket available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. 2. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.
English Connecting Composite Video source devices Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. 2. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
English Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. 2. Press POWER on the projector or remote control to start the projector and a start up tone sounds. The POWER indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds.
English Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overview of the OSD menu. Main menu icon Main menu DISPLAY Off Wall Color Auto Aspect Ratio Highlight Sub-menu On Auto Keystone Keystone Status Position ENTER Phase 15 0 H. Size Digital Zoom 3D Sync Off 3D Sync Invert Current input signal Disable COMPUTER 1/Y Pb Pr 1 Press MENU/ EXIT to the previous page or to exit.
English Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 26. You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password.
English If you forget the password If the password function is activated, you will be asked to enter the five-digit password every time you turn on Password Error the projector. If you enter the wrong password, the Please Try again. password error message as pictured to the right displays lasting for three seconds, and the message 'INPUT PASSWORD' follows.
English Disabling the password function To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on Lock menu after opening the OSD menu system. Select Off by pressing / . The message 'INPUT PASSWORD' displays. Enter the current password. i. If the password is correct, the OSD menu returns to the Security Settings page with Off show in the row of Power on Lock. You will not have to enter the password next time you turn on the projector. ii.
English Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of this projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. 2. Press SOURCE on the projector or remote control. A source selection bar displays.
English Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. 2. Screw the rear adjuster foot to fine tune the horizontal angle.
English Fine-tuning the image size and clarity 1. Adjust the projected image to the size that you need using the ZOOM ring. FOCUS ZOOM 2. Then sharpen the image by rotating the FOCUS ring. FOCUS Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.
4. English 5. Press to highlight Keystone and press MODE/ENTER. The Keystone correction page displays. Press to correct keystoning at the top of the KEYSTONE image or press to correct keystoning at the bottom of the image. 6 MENU Back Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press Zoom +/- to display the Zoom bar. 2.
English Playing 3D function 1. 2. 3. To enter the special preset mode, press MENU/EXIT and then press / until the DISPLAY menu is highlighted, and press / to enable or disable 3D Sync. When the 3D Sync is enabled, the current picture mode adjustment will be disabled. To invert the image, press MENU/EXIT and then press / until the DISPLAY menu is highlighted, and press / to enable or disable 3D Sync Invert.
About the aspect ratio English In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. 2. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio.
English Optimizing the image Using Wall Color In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Wall Color feature can help correct the projected picture’s color to prevent possible color difference between the source and projected pictures. To use this function, go to the DISPLAY > Wall Color menu and press / to select a color which is the closest to the color of the projection surface.
Setting the User 1/User 2 mode English There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2) as a starting point and customize the settings. 1. 2. 3. 4. Press MENU/EXIT to open the On-Screen Display (OSD) menu. Go to the PICTURE > Picture Mode menu. Press / to select User 1 to User 2. Press to highlight Reference Mode.
Adjusting Color English Highlight Color in the PICTURE menu and adjust the values by pressing projector or remote control. / on the Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic. Adjusting Tint Highlight Tint in the PICTURE menu and adjust the values by pressing projector or remote control. / on the The higher the value, the more reddish the picture becomes.
3D Color Management English In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room. Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered.
English Setting the presentation timer The presentation timer can indicate the presentation Presentation Timer Timer period time on the screen to help you achieve better time 15 Always Timer display management when giving presentations. Follow these Timer position Top-Left Timer counting direction Count Down steps to utilize this function: Off Sound reminder Off 1. Go to the SYSTEM SETUP: Basic > On Back Presentation Timer menu and press MODE/ ENTER to display the Presentation Timer page. 2.
3. English Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is Off” displaying on the screen. Remote paging operations Connect the projector to your PC or notebook with a USB cable prior to using the paging function. See "Connecting a computer" on page 18 for details. You can operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint) by pressing PAGE / on the remote control.
English Locking control keys With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except POWER. 1. 2. / on the projector or go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select Press On by pressing / on the projector or remote control. A confirmation message displays. Select Yes to confirm.
English Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea level, and temperature is between 5°C–23°C. Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 5°C and 28°C. The projector will be over cooled, if you turn the mode on under such a condition. To activate the High Altitude Mode: Notice 1.
English Adjusting the sound The sound adjustments made as below will have an effect on the projector speakers. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 18 for how the audio input is connected. INPUT SOUCER D-Sub-15 AUDIO IN AUDIO OUT RGB mini jack mini jack Component RCA mini jack HDMI HDMI mini jack VIDEO RCA mini jack S-VIDEO RCA mini jack Muting the sound 1. 2. 3. 4.
English Controlling the projector through a Lan environment Lan Control Settings allow you to manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network. Configuring the Lan Control Settings If you are in a DHCP environment: 1. 2. 3. 4. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port.
If you are in a non-DHCP environment: English 1. 2. Repeat steps 1-4 above. Projector will restore the latest IP configuration into Lan Control Settings. (*1) Network Network State Disconnect DHCP Off Projector IP Address 0.0.0.0 Subnet Mask 0.0.0.0 Dedault Gateway 0.0.0.0 DNS 0.0.0.0 Apply MENU Back 3. 4. 5. 6. 7. 8. Press to highlight DHCP and press / to select Off.
English i. These buttons function the same as the ones on the OSD menus or remote control. See "Using the menus" on page 26 and "Remote control" on page 11 for details. The Menu button can also be used to go back to previous OSD menu, exit and save menu settings. ii. To switch input source, click on your desired signal. The tools page allows you to manage the projector, configure the Lan control settings and secure access of remote network operation on this projector. i iii ii iv v i.
The info page displays the information and status of this projector. English Press Exit to go back to the remote network operation page. For more information, visit http://www.crestron.com. If you are an IT administrator and would like to manage multiple devices through one interface, you can download Crestron Roomview at www.crestron.com/getroomview.
English Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • • • • Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.
English Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu 1. DISPLAY Sub-menu Options Wall Color Off/Light Yellow/Pink/Light Green/Blue/Blackboard Aspect Ratio Auto/Real/4:3/16:9 Auto Keystone On/Off Keystone Position Phase H.
English FAQ-Image and Installation FAQ-Features and Service 6. INFORMATI Current System Status ON Presentation Timer • • • • • • Source Picture Mode Resolution Color System Equivalent Lamp Hour Firmware Version Timer period 1~240 minutes Timer display Always/1 min/2 min/3 min/Never Timer position Top-Left/Bottom-Left/Top-Right/ Bottom-Right Timer counting direction Count Down/Count Up Sound reminder On/Off On/Off Language 4.
Quick Cooling Off/On English High Altitude Mode Off/On Audio Settings Mute Volume Power on/off ring tone Off/On Range : 0 ~ 10 Off/On Lamp Mode Normal/Economic Lamp Settings Reset lamp timer Equivalent Lamp Hour Security Settings 5.
FUNCTION English Description of each menu (default setting/ value) DESCRIPTION (default setting/value) Wall Color Corrects the projected picture’s color when the projection surface is not white. See "Using Wall Color" on page 36 for details. (Off) Aspect Ratio (Auto) Auto Keystone There are four options to set the image's aspect ratio depending on your input signal source. See "Selecting the aspect ratio" on page 34 for details. Corrects any keystoning of the image automatically.
English Picture Mode Pre-defined picture modes are provided so you can optimize your (Dynamic) projector image set-up to suit your program type. See "Selecting a picture mode" on page 36 for details. Selects a picture mode that most suits your need for the image quality and further fine-tune the image based on the selections listed on the same page below. See "Setting the User 1/User 2 mode" on page 37 for details. Brightness Adjusts the brightness of the image.
(default setting/ value) English FUNCTION DESCRIPTION (default setting/value) Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 40 for details. Timer period (15 min.) Presentation Timer (Off) Sets a preferred length of time for presentation. Timer display (Always) Sets whether to display the timer on screen. Timer position (Top-Left) Sets the position where the timer displays on screen.
English Quick Cooling (On) Selecting On enables the function and the projector cooling time will be shortened to a few seconds. If you attempt to restart the projector right after the quick cooling process, it may not be turned on successfully and will rerun its cooling fans. High Altitude A mode for operation in high altitude areas. See "Operating in a high Mode altitude environment" on page 43 for details.
(default setting/ value) FAQ-Image and Installation 6. INFORMATION menu FAQFeatures and Service English FUNCTION DESCRIPTION (default setting/value) Displays possible solutions to problems you may encounter. Source Shows the current signal source. Picture Mode Shows the selected mode in the PICTURE menu. Current System Status Resolution Shows the native resolution of the input signal. Color System Shows input system format, NTSC, PAL, SECAM, or RGB.
English Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust.
English Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows: Total (equivalent) lamp hour = 1 (hours used in Economic mode) + 4/2.5 for the MP626 | 4/3 for the MP670 (hours used in normal mode) See "Setting Lamp mode as Economic" below for more information on Economic mode. To obtain the lamp hour information: 1.
English Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.benq.com for a replacement lamp. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp. • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
5. English Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed.
Resetting the lamp timer English 11. After the startup logo, open the On-Screen Notice Display (OSD) menu. Go to the SYSTEM Reset Lamp Timer? SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER. The Lamp Cancel Reset Settings page displays. Press to highlight Reset lamp timer and press MODE/ENTER. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to '0'.
English Indicators Light Power Status & Description Temp Lamp Power events Orange Off Off Stand-by mode Green Flashing Off Off Powering up Green Off Off Normal operation Orange Flashing Off Off The projector needs to cool for 90 seconds after the power is turned off. Lamp events Orange Flashing Off Red The lamp ignition retries if the lamp fails during startup. Off Off Red 1. 2. The projector needs 90 seconds to cool down. Or Please contact your dealer for assistance.
English Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cable. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
English Specifications Projector specifications All specifications are subject to change without notice. General Product name Model name Digital Projector MP626 MP670 Optical Resolution Display system Lens F/Number Lamp 180 W lamp 1024 x 768 XGA 1-CHIP DMD F = 2.52 to 2.73, f = 21.8 to 24 mm 230 W lamp Electrical Power supply Power consumption AC100–240V, 50/60 Hz (Automatic) 245W (Max)/ 310W (Max)/ <1W (Standby) <1W (Standby) Mechanical Dimensions Weight 306 mm (W) x 97 mm (H) x 216 mm (D) 6.
English Dimensions 306 mm (W) x 97 mm (H) x 216 mm (D) 306.00 216 97 55.20 75 Ceiling Mount Installation 66 196 * Ceiling Mount Screws: M4 x 14 (Max. L=14, Min. L=12) 54 98 60 109.22 106.
English Timing chart Supported timing for PC input Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 31.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72 37.500 75.000 31.500 VGA_75 43.269 85.008 36.000 VGA_85 37.927 85.039 35.5 720 x 400 x 85 35.2 56.3 36 SVGA_56 37.879 60.317 40.000 SVGA_60 48.077 72.188 50.000 SVGA_72 46.875 75.000 49.500 SVGA_75 53.674 85.061 56.250 SVGA_85 48.363 60.004 65.000 XGA_60 56.476 70.
Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 55.935 59.887 106.500 WXGA+_60 70.635 74.984 136.750 WXGA+_75 1400 x 1050 65.317 59.978 121.750 SXGA+_60 1600 x 1200 75.000 60.000 162.000 UXGA 640 x 480@67Hz 35.000 66.667 30.240 MAC13 832 x 624@75Hz 49.722 74.546 57.280 MAC16 1024 x 768@75Hz 60.240 75.020 80.000 MAC19 1152 x 870@75Hz 68.68 75.06 100.000 MAC21 1024 x 576@60Hz 35.82 60 46.996 1024 x 576-GTF 1024 x 600@60Hz 37.
English Supported timing for Component-YPbPr input Signal Format Horizontal Frequency (kHz) Vertical Frequency (Hz) 480i(525i)@60Hz 15.73 59.94 480p(525p)@60Hz 31.47 59.94 576i(625i)@50Hz 15.63 50.00 576p(625p)@50Hz 31.25 50.00 720p(750p)@60Hz 45.00 60.00 720p(750p)@50Hz 37.50 50.00 1080i(1125i)@60Hz 33.75 60.00 1080i(1125i)@50Hz 28.13 50.00 1080P@60Hz 67.5 60.00 1080P@50Hz 56.26 50.
Resolution 720 x 400 Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) English Supported timing for HDMI (HDCP) input Mode 37.927 85.039 35.5 720 x 400_85 31.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72 37.500 75.000 31.500 VGA_75 43.269 85.008 36.000 VGA_85 35.2 56.3 36 SVGA_56 37.879 60.317 40.000 SVGA_60 48.077 72.188 50.000 SVGA_72 46.875 75.000 49.500 SVGA_75 53.674 85.061 56.250 SVGA_85 48.363 60.004 65.000 XGA_60 56.
English Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 1600 x 1200 75.000 60.000 162.000 UXGA 640 x 480@67Hz 35.000 66.667 30.240 MAC13 832 x 624@75Hz 49.722 74.546 57.280 MAC16 1024 x 768@75Hz 60.241 75.020 80.000 MAC19 1152 x 870@75Hz 68.68 75.06 100.000 MAC21 1024 x 576@60Hz 35.82 60 46.996 1024 x 576-GTF 1024 x 600@60Hz 37.32 60 48.964 1024 x 600-GTF 31.47 60 27 480p 31.25 50 27.000 576p 37.50 50 74.
English Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).
English Regulation statements FCC statement CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
English Accessibility Requirements for Rehabilitation Act of 1973, Section 508 BenQ's commitment to accessible products allows us to support government in making accessible technology choices BenQ's LCD monitors and projectors are compliant with Section 508 guidelines by including the assistive features as below: • • • • • • • • • • BenQ's monitors have colored "Power" indicators. While the indicator shows green, it means that the monitor is using the full power.
