MS517/MX518/MW519/MS517F/MX518F MX503H/MS507H/TW519 Digital Projector User Manual
Table of contents Important safety instructions ................... 3 Introduction.................. 7 Projector features.....................................7 Shipping contents ......................................8 Projector exterior view...........................9 Positioning your projector ..................... 15 Select the lamp saver mode ................. 44 Shutting down the projector ............... 45 Menu operation ...................................... 46 Maintenance ...............
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation.
Safety Instructions (Continued) 4 7. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. 8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions. 9. Never replace the lamp assembly or any electronic components unless the projector is unplugged. Important safety instructions 10.
Safety Instructions (Continued) 13. Do not place this projector in any of the following environments. 14. Do not block the ventilation holes. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. - Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.
Safety Instructions (Continued) 16. 18. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector. 17. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury. 19. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail.
Introduction Projector features This model is one of the best projectors available in the world. You can enjoy the best performance video quality with up to 300-inch projection across various devices such as PC, laptop, DVD and VCR even document camera to bring all possibility to life.
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
Projector exterior view 1. Front/upper side 1 2 3 4 6 7 8 9 5 18 19 13 20 14 15 16 17 21 9 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Rear/lower side 10 11 12 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. External control panel (See "Projector" on page 10 for details.
Controls and functions Projector 7. 1 2 3 9 10 4 5 6 11 7 7 12 8 13 8. 9 9. 1. 2. 3. 4. 5. 6. 10 Focus ring Adjusts the focus of the projected image. See "Fine-tuning the image size and clarity" on page 26 for details. Zoom ring Adjusts the size of the image. See "Finetuning the image size and clarity" on page 26 for details. TEMP(temperature) warning light Lights up red if the projector's temperature becomes too high. See "Indicators" on page 65 for details.
Ceiling mounting the projector We want you to have a pleasant experience using your BenQ projector, so we need to bring this safety matter to your attention to prevent possible damage to person and property. If you intend to mount your projector on the ceiling, we strongly recommend that you use a proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely installed.
Remote control 5. 1 11 12 2 13 3 3 4 5 14 12 6 15 7 16 17 8 18 19 9 20 10 21 22 1. 2. 3. 4. 12 Eco Blank Press the Eco Blank button to turn off the image for a period of time with 70% lamp power saving. Press again to restore the image. See "Hiding the image" on page 41 for details. 6. SmartEco Displays the lamp mode selection bar(Normal/Economic/SmartEco). 7. Aspect Selects the display aspect ratio. See "About the aspect ratio" on page 34 for details. 8.
14. Source Displays the source selection bar. See "Switching input signal" on page 32 for details. 15. Volume +/Adjusts the sound level. See "Adjusting the sound" on page 42 for details. 16. Page Up/Down Page up/down arrows when connected through USB to a PC. See "Remote paging operations" on page 40 for details. 17. Mute Toggles projector audio between on and off. 18. Freeze Freezes the projected image. See "Freezing the image" on page 41 for details. 19.
Replacing the remote control battery 1. 2. 3. To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated. The cover will slide off. Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1.
Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. Projection dimensions Refer to "Dimensions" on page 69 for the center of lens dimensions of this projector before calculating the appropriate position.
MW519/TW519 The screen aspect ratio is 16:10 and the projected picture is 16:10 Screen size Projection distance (mm) Diagonal W H Min Average Max (mm) (mm) distance distance Inch mm (max. (min.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. • In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores. • For detailed connection methods, see pages 19-23.
Connecting a computer or monitor Connecting a computer The projector can connect to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a notebook or desktop computer: 1. 2. 3. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN-1 or COMPUTER IN-2 signal input jack on the projector.
Connecting Video source devices You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
Connecting a HDMI source device The projector provides a HDMI input jack that allows you to connect it to a HDMI source device like a DVD player, a DTV tuner or a display. HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays over a single cable. It provides pure digital viewing and listening experience.
Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output jacks available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. 2. 3.
Connecting an S-Video/composite source device Examine your Video source device to determine if it has an unused S-Video/composite output jack available: • • • If it has both jacks, use the S-Video output jack for connection as the S-Video terminal provides better picture quality than the Video terminal. If it has either of the output jack, you can also continue with this procedure. If not, you will need to reassess which method you can use to connect to the device.
Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. • Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire.
You can also press Source on the projector or remote control to select your desired input signal. See "Switching input signal" on page 32 for details. • If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK mode. Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1.
Use build-in test pattern You can adjust the image shape and focus status by observing the input signal content, or using the test pattern build-in OSD manual from OSD or remote control for better observe the shape changed. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Test Pattern > On. Press MODE/ENTER. The Test Pattern displays. Fine-tuning the image size and clarity 26 1. Adjust the projected image to the size that you need using the zoom ring. 2.
Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overview of the OSD menu. Main menu icon Main menu Highlight Status Sub-menu Press MENU/ EXIT to the previous page or to exit. Current input signal The following example describes how to set the OSD language. 1. Press MENU/EXIT on the projector or remote control to turn the OSD menu on. 3. Press to highlight Language and press Enter to select a preferred language.
Securing the projector Using a security cable lock The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the rear side of the projector. See item 17 on page 9 for details. A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock's documentation for finding out how to use it.
If you forget the password If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right displays lasting for three seconds, and the message 'INPUT PASSWORD' follows. You can retry by entering another six-digit password, or if you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure.
6. 7. You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started. To leave the OSD menu, press MENU/EXIT. Disabling the password function To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on lock menu after opening the OSD menu system. Select Off by pressing / . The message 'INPUT PASSWORD' displays. Enter the current password.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals. Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of this projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1.
Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press Digital Zoom +/- to display the Zoom bar. 2. Press Digital Zoom + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4.
1. 2. 3. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted. Press to highlight Aspect Ratio. Press / to select an aspect ratio to suit the format of the video signal and your display requirements. About the aspect ratio 1. 2. 3. 4. 5. 34 Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal or vertical width.
Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps. • • Press MODE/ENTER on the remote control or projector repeatedly until your desired mode is selected. Go to the PICTURE > Picture Mode menu and press / mode. to select a desired The picture modes are listed below.
Using Wall Color In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Wall Color feature can help correct the projected picture’s color to prevent possible color difference between the source and projected pictures. To use this function, go to the DISPLAY > Wall Color menu and press / to select a color which is the closest to the color of the projection surface.
*About color temperatures: There are many different shades that are considered to be "white" for various purposes. One of the common methods of representing white color is known as the “color temperature”. A white color with a low color temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it. Setting a preferred color temperature To set a preferred color temperature: 1. 2. 3. 4.
5. 6. 7. 8. 9. Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its Yellow GREEN RED range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta. Cyan Magenta Press to highlight Saturation and adjust its values to your preference by pressing / BLUE . Every adjustment made will reflect to the image immediately.
Setting the presentation timer The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. 2. 3. Press Timer Set up on the remote control or go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/ ENTER to display the Presentation Timer page. Highlight Timer Period and decide the timer period by pressing / .
To cancel the timer, perform the following steps. • Using the remote control. Press Timer On and press / to highlight Off and press MODE/ENTER. • Using the OSD menu. 1. Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight Off. Press MODE/ENTER. A confirmation message displays. 2. Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is Off!” displaying on the screen. How to use the Timer On key? Timer On is a multi-functional key.
Hiding the image Press the Eco Blank button from projector or remote control to turn off the image for a period of time with up to 70% lamp power saving. Press any key on the projector or remote control to restore the image. The word "Eco Blank" appears at the screen while the image is hidden. When this function is activated with an audio input connected,the audio can still be heard. • Eco Blank: Save up 70% of your lamp power. Time to do your part in saving the planet.
Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is 1500 m – 3000 m above sea level, and ambient temperature is between 0°C–35°C. Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition. To activate the High Altitude Mode: 1.
Use Teaching Template Making writing on the board easier for teachers, you can use build-in template by OSD or remote control. Open the OSD menu and go to the DISPLAY > Teaching Template . Choice Blackboard/ Whiteboard. > Off/ Letter Formation/ Worksheet/ Coordinate Chart. The Teaching Template displays.
Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • • • • • Menu display Time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.
Shutting down the projector 1. Press II POWER and a confirmation message displays prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press II POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. • To protect the lamp, the projector will not respond to any commands during the cooling process.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu Sub-menu Options Wall Color Off/Light Yellow/Pink/Light Green/ Blue/Blackboard Aspect Ratio Auto/Real/4:3/16:9/16:10 Keystone Position Phase 1. DISPLAY H.
Presentation Timer Timer Period 1~240 minutes Timer Display Always/3 min/2 min/1 min/Never Timer Position Top-Left/Bottom-Left/Top-Right/ Bottom-Right Timer Counting Direction Count Down/Count Up On/Off Yes/No Language Projector Installation 4.
High Altitude Mode Audio Settings Lamp Settings On/Off Yes/No Mute On/Off Volume 0~10 Lamp Mode Normal/Economic/SmartEco Reset Lamp Timer Reset/Cancel Equivalent Lamp 5.
Description of each menu • The default values listed in this manual, especially on pages 49-57, are for reference only. They may vary between the projectors due to the continuous improvement to the products. FUNCTION DESCRIPTION Wall Color Corrects the projected picture’s color when the projection surface is not white. See "Using Wall Color" on page 36 for details. There are four options to set the image's aspect ratio depending on your input signal source.
FUNCTION DESCRIPTION This projector features a 3D function which enables you to enjoy the 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view the 3D images. 1. DISPLAY menu 3D 3D Sync Invert When you discover the inversion of the image depth, enable this function to correct the problem. Provides some templates as teaching aids. Teachers can use them for teaching.
FUNCTION DESCRIPTION Pre-defined picture modes are provided so you can optimize your Picture Mode projector image set-up to suit your program type. See "Selecting a Reference Mode Brightness 2. PICTURE menu Contrast Color picture mode" on page 35 for details. Selects a picture mode that best suits your need for the image quality and further fine-tune the image based on the selections listed on the same page below. See "Setting the User 1/User 2 mode" on page 35 for details.
FUNCTION DESCRIPTION Brilliant Color See "Adjusting Brilliant Color" on page 36 for details. 2. PICTURE menu See "Selecting a Color Temperature" on page 36 for details. Color Temperature See "Setting a preferred color temperature" on page 37 for details. Color Temperature Fine Tuning 3D Color Management See "3D Color Management" on page 37 for details. See "Resetting current or all picture modes" on page 38 for details.
4. SYSTEM SETUP: Basic menu FUNCTION DESCRIPTION Presentation Timer Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 39 for details. Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 28 for details. The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 15 for details.
FUNCTION DESCRIPTION Direct Power On Selecting On enables the function. See "Starting up the projector" on page 24 for details. Auto Power Off Allows the projector to turn off automatically if no input signal is detected after a set period of time. See "Setting Auto Power Off" on page 59 for details. Quick Cooling Selecting On enables the function and the projector cooling time will be shortened to a few seconds. 4.
FUNCTION DESCRIPTION High Altitude A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 42 for details. Mode Allows you to enter the audio setting menu. 5. SYSTEM SETUP: Advanced menu Audio Settings Mute Sets the mute function. Lamp Settings Reset Lamp Timer See "Resetting the lamp timer" on page 64 for details. Security Settings Baud Rate Test Pattern Volume Adjusts the audio volume level.
FUNCTION DESCRIPTION Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions. Closed Caption • 5. SYSTEM SETUP: Advanced menu Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). Caption Version Selects a preferred closed captioning mode.
FUNCTION DESCRIPTION Source Shows the current signal source. 6. INFORMATION menu Picture Mode Shows the selected mode in the PICTURE menu. Resolution Shows the native resolution of the input signal. Current System Status Lamp Mode Shows the current lamp mode. 3D Format Shows the current 3D mode. Color System Shows input system format, NTSC, PAL, SECAM, or RGB. Equivalent Lamp Displays the number of hours the lamp has been used. Firmware Version Shows firmware version.
Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens and case clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • • Use a canister of compressed air to remove dust.
Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows: Total (equivalent) lamp hour = 1 (hours used in Economic mode) + 4/3 (hours used in normal mode) See "Setting Lamp mode eco function as Economic or SmartEco mode" below for more information on Economic mode.
increments. If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.
Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot.
Replacing the lamp • Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org. • If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp. • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.
3. • Remove the lamp cover by (a) sliding the cover toward the side of the projector and (b) lifting it off. Do not turn the power on with the lamp cover removed. • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries. 4. Loosen the screws that secure the lamp. 5. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector.
7. Tighten the screws that secure the lamp. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws. 8. Ensure the handle is fully laid flat and locked in place. 9. Replace the lamp cover by sliding it into place. (a) (b) 10. Tighten the screw that secures the lamp cover. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 11. Restart the projector.
Indicators Light POWER TEMP Status & Description LAMP Power events Orange Off Off Green Flashing Off Off Green Off Off Orange Flashing Off Off Red Off Off Green Off Red Red Flashing Off Off Red Off Red Green Off Off Green Green Green Stand-by mode Powering up Normal operation Normal power-down cooling Download CW start fail Scaler shutdown fail (data abord) Scaler reset fail (video projector only) Burn-in ON Burn-in OFF Lamp events Off Off Off Off Red Lamp1 error in norma
Green Flashing 66 Green Flashing Maintenance Off Thermal IC #2 I2C Connection error
Troubleshooting The projector does not turn on. Cause Remedy Plug the power cord into the AC inlet on the projector, and plug the power cord into the There is no power from the power cable. power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again Wait until the cooling down process has during the cooling process. completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications All specifications are subject to change without notice. Optical 2.3 Kg (5.1 lbs) Output terminals Resolution (MS517/MS517F/MS507H) 800 x 600 SVGA (MX518/MX518F/MX503H) 1024 x 768 XGA (MW519/TW519) 1280 x 800 WXGA Display system 1-CHIP DMD Lens F/Number (MS517/MX518/MS517F/MX518F/ MX503H/MS507H) F = 2.51 to 2.69, f = 21.95 to 24.18 mm (MW519/TW519) F = 2.55 to 3.06 f = 21 to 25.
Dimensions 301.6 mm (W) x 111.3 mm (H) x 219.2 mm (D) 301.6 219.2 111.3 70.0 76 Ceiling mount installation Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 196.0 181.0 80.0 Unit: mm 81.0 21.0 196.0 71.9 301.6 57.5 162.
Timing chart Supported timing for PC input Resolution Mode Vertical Frequency (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) 640 x 480 VGA_60* VGA_72 VGA_75 VGA_85 720 x 400_70 SVGA_60* SVGA_72 SVGA_75 SVGA_85 SVGA_120** (Reduce Blanking) XGA_60* XGA_70 XGA_75 XGA_85 XGA_120** (Reduce Blanking) 1152 x 864_75 BenQ Notebook_ timing BenQ Notebook_ timing 1280 x 720_60* 1280 x 768_60* WXGA_60* WXGA_75 WXGA_85 WXGA_120** (Reduce Blanking) SXGA_60*** SXGA_75 SXGA_85 1280 x 960_60*** 1280 x 960_85 136
Supported timing for HDMI (HDCP) input Resolution Mode Vertical Frequency (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) 640 x 480 VGA_60* VGA_72 VGA_75 VGA_85 720 x 400_70 SVGA_60* SVGA_72 SVGA_75 SVGA_85 SVGA_120** (Reduce Blanking) XGA_60* XGA_70 XGA_75 XGA_85 XGA_120** (Reduce Blanking) 1152 x 864_75 1280 x 768_60* BenQ Notebook_ timing BenQ Notebook_ timing 1280 x 720_60 1280 x 768_60 WXGA_60* WXGA_75 WXGA_85 WXGA_120** (Reduce Blanking) SXGA_60*** SXGA_75 SXGA_85 1280 x 960_60*** 1280 x 9
• The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible that some timings cannot be chosen.
Supported timing for Component-YPbPr input Timing Resolution Vertical Frequency (Hz) Horizontal Frequency (kHz) Pixel Frequency (MHz) 480i* 480p 576i 576p 720/50p 720/60p 1080/50i 1080/60i 1080/24P 1080/25P 1080/30P 1080/50P 1080/60P 720 x 480 720 x 480 720 x 576 720 x 576 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 59.94 59.94 50 50 50 60 50 60 24 25 30 50 60 15.73 31.47 15.63 31.25 37.5 45.00 28.13 33.75 27 28.13 33.75 56.25 67.5 13.
Supported 3D signal for HDMI (HDCP) input Video timing Resolution Timing 720 (1440) x 480 720 x 480 720 (1440) x 576 720 x 576 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 480i Horizontal frequency (KHz) 15.73 Vertical frequency (Hz) 59.94 480p 576i 31.47 15.63 59.94 50 576p 720/50p 720/60p 1080/ 24P 1080/ 25P 1080/ 30P 1080/50i 1080/60i 1080/ 50P 1080/ 60P 31.25 37.5 45 27 50 50 60 24 28.13 25 33.75 30 28.13 33.75 56.
1280 x 800 1280 x 1024 1280 x 960 1360 x 768 1440 x 900 1400 x 1050 1600 x 1200 1680 x 1050 1920 x 1200 640 x 480 @67Hz 832 x 624 @75Hz 1024 x 768 @75Hz 1152 x 870 @75Hz 1920 x 1080 (VESA) WXGA_60 WXGA_75 WXGA_85 WXGA_120 (Reduce Blanking) SXGA_60 SXGA_75 SXGA_85 1280 x 960_60 1280 x 960_85 1360 x 768_60 WXGA+_60 (Reduce Blanking) WXGA+_60 SXGA+_60 UXGA 1680 x 1050_60 (Reduce Blanking) 1680 x 1080_60 1920 x 1200_60 (Reduce Blanking) MAC13 59.81 74.934 84.88 119.909 49.702 62.795 71.554 101.563 60.
1280 x 720 1280 x 768 1280 x 800 1280 x 1024 1280 x 960 1360 x 768 1440 x 900 1400 x 1050 1600 x 1200 1680 x 1050 1920 x 1200 640 x 480 @67Hz 832 x 624 @75Hz 1024 x 768 @75Hz 1152 x 870 @75Hz 1920 x 1080 (VESA) 1280 x 720_60 1280 x 720_120 1280 x 768_60 (Reduce Blanking) 1280 x 768_60 WXGA_60 WXGA_75 WXGA_85 WXGA_120 (Reduce Blanking) SXGA_60 SXGA_75 SXGA_85 1280 x 960_60 1280 x 960_85 1360 x 768_60 WXGA+_60 (Reduce Blanking) WXGA+_60 SXGA+_60 UXGA 1680 x 1050_60 (Reduce Blanking) 1680 x 1050_60 1920 x 1
Warranty and Copyright information Patents This BenQ projector is covered by the following patents: U.S. patents 6,837,608; 7,275,834; 7,181,318; TW patents 202690; 205470; I228635; I259932; China Patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0; ZL200510051609.2 Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim.
