SP840 Digital Projector User Manual Welcome
English Table of contents Important safety instructions .......................3 Introduction......................7 Projector features ................................. 7 Shipping contents................................. 8 Projector exterior view......................... 9 Controls and functions ....................... 10 Personalizing the projector menu display 46 Shutting down the projector .............. 46 Menu operation.................................. 47 Maintenance ...................
English Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation.
English Safety Instructions (Continued) 4 6. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. 9. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage. 7. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions. 10.
English Safety Instructions (Continued) 12. Do not place this projector in any of the following environments. 13. - Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector. - Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.
English Safety Instructions (Continued) 16. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury. 17. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced. 18.
English Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.
English Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated.
Front/upper side 1 5 6 2 3 1. 2. 3. 4. 5. 6. 7. 8. English Projector exterior view Vent (heated air exhaust) Lamp cover Quick-release button Projection lens External control panel (See "Projector" on page 10 for details.) Vent (cool air intake) Focus ring and Zoom ring Front IR remote sensor 7 SP 840 4 7 8 Rear/lower side 9 10 11 29 12 13 14 15 16 17 18 19 28 27 26 25 24 23 22 20 21 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29.
English Controls and functions Projector 6. MODE/ENTER Selects an available picture setup mode. See "Selecting a picture mode" on page 34 for details. Enacts the selected On-Screen Display (OSD) menu item. See "Using the menus" on page 26 for details. 7. Left/ Starts the INFORMATION function. BLANK Used to hide the screen picture. See "Hiding the image" on page 40 for details. FOCUS/ZOOM Ring Used to adjust the projected image appearance.
1 2 15 15 16 16 17 18 3 4 19 5 2 17 18 3 4 19 5 6 20 7 6 20 7 8 21 22 9 8 21 22 9 10 23 10 23 11 24 11 24 12 25 13 14 12 26 13 27 14 25 26 27 28 28 Standard remote 1. Laser (Standard Remote only) Use as on-screen pointer. DO NOT POINT IN EYES. 2. POWER Toggles the projector between standby mode and on. See "Starting up the projector" on page 25 and "Shutting down the projector" on page 46 for details. Enter Enter key when connected through USB to a PC.
. English 13. 14. 15. 16. 17. 18. 19. MENU Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings. See "Using the menus" on page 26 for details. AUTO Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 30 for details. SOURCE Displays the source selection bar. See "Switching input signal" on page 29 for details. IR transmitter Transmits signals to projector.
Remote control effective range App rox . ±15 ° App r ox. SP ± 15 English Infra-Red (IR) remote control sensor is located on the front and the rear of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 7 meters (~ 23 feet).
English Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1.
English Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. 16:9 is the native aspect ratio. SP840 can project a complete 16:9 (widescreen) image.
English How to determine the position of the projector for a given screen size 1. 2. Select your screen size. Refer to the table and find the closest match to your screen size in the left columns labelled "16:9 screen". Using this value, look across this row to the right to find the corresponding average distance from screen value in the column labelled "Average". This is the projection distance. 3. On that same row, look across to the right column and make note of the "Vertical offset in mm" value.
English SP840 projection dimensions Refer to "Dimensions" on page 64 for the center of lens dimensions of this projector before calculating the appropriate position.
English Connections When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.
English Connecting a monitor If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the MONITOR OUT signal output socket on the projector to an external monitor with a VGA or VGA to DVI-A cable by following the instructions below. To connect the projector to a monitor: • With a VGA cable: • With a VGA to DVI-A cable: Your monitor must be equipped with a DVI input socket. 1. 2. 3.
English Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output jacks: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
English Connecting HDMI source devices The projector provides a HDMI input jack that allows you to connect it to a HDMI source device like a DVD player, a DTV tuner or a display. HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays over a single cable. It provides pure digital viewing and listening experience.
English Connecting Component Video source devices Examine your Video source device to determine if it has a set of unused Component Video output jacks available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. 2. Take a Component Video cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device.
English Connecting S-Video source devices Examine your Video source device to determine if it has an unused S-Video output socket available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. 2. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.
English Connecting Composite Video source devices Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: 1. 2. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
English Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire. 2. Press POWER on the projector or remote control to start the projector and a start up tone sounds.
English Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overview of the OSD menu. Main menu icon Main menu PICTURE : Basic User 1 Picture Mode Reference Mode Brightness Highlight Sub-menu Dynamic 50 Contrast 0 Color 0 Tint 0 Sharpness 0 Flesh Tone 0 Status Save Setting Press MENU/ EXIT to the previous page or to exit.
English Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 26. You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password.
English Entering the password recall procedure 1. 2. 3. Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. RECALL PASSWORD Please write down the recall code, and contact BenQ Customer Center.
English Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On (which is the default of this projector) if you want the projector to automatically search for the signals. You can also manually cycle through the available input signals. 1. 2. Press SOURCE on the projector or remote control. A source selection bar displays.
English Adjusting the projected image Adjusting the projection angle Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle. The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector.
English Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, and use Auto Keystone or Keystone to manually correct it following one of these steps. • Using Auto Keystone It can correct Keystone to optimal status by automatically. • Using the remote control 1.
English Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press Zoom +/- to display the Zoom bar. 2. Press Zoom + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4.
About the aspect ratio English In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector’s native resolution in its horizontal width and vertical height. This is suitable for the incoming image which is in 4:3 or 16:9 and you want to make most use of the screen without altering the image’s aspect ratio. 4:3 picture 16:9 picture 2. 3. 4. 5.
English Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps. • • Press MODE/ENTER on the projector repeatedly until your desired mode is selected. Go o thet PICTURE: Basic > Picture Mode menu and press / to select a desired mode.
English Fine-tuning the image quality in user modes According to the detected signal type, there are some user-definable functions available when User 1, User 2 or User 3 mode is selected. You can make adjustments to these functions based on your needs. Adjusting Brightness Highlight Brightness in the PICTURE: Basic menu and adjust the values by pressing on the projector or remote control. The higher the value, the brighter the image. And lower the setting, darker the image.
Adjusting Clarity Control English Highlight Clarity Control in the PICTURE: Advanced menu and adjust the values by pressing MODE/ENTER on the projector or remote control. To adjust the settings: 1. Noise Reduction: Reduces electrical image noise caused by different media players. The higher the setting, the less the noise. Highlight Noise Reduction and press / to adjust the value from 0 to 15. 2. Detail Enhancement: Sharpens the image. The higher the setting, the more details the image reveals.
Adjusting Brilliant Color English Highlight Brilliant Color in the PICTURE: Advanced menu and select by pressing / on the projector or remote control. This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors.
English To adjust the settings: 1. Go to the PICTURE: Advanced menu and highlight 3D Color Management. 2. Press MODE/ENTER and the 3D Color Management page displays. 3. Highlight Primary color and press / to select a color from among Red, Green, Blue, Cyan, Magenta and Yellow. 4. Press to highlight Hue and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors.
Selecting a Film Mode / on English Highlight Film Mode in the PICTURE: Advanced menu and select by pressing the projector or remote control. On is the default and recommended selection for this projector. When Off is selected, the Film Mode function is not available. This function is only available when Video or S-Video with NTSC system is selected. Selecting a 3D Comb Filter Highlight 3D Comb Filter in the PICTURE: Advanced menu and select by pressing / on the projector or remote control.
English Hiding the image In order to draw the audience's full attention to the presenter, you can use BLANK on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden.
English Freezing the image Press FREEZE on the remote control to freeze the image. The word 'FREEZE' will display in the upper left corner of the screen. To release the function, press any key on the projector or remote control. Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen on screen.
Muting the sound English To temporarily turn off the sound, • Using the remote control Press MUTE to temporarily turn off the sound. While the sound is off, the screen will display in the upper right corner of the screen. To restore the sound, press MUTE again. • Using the OSD menu 1. Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. 2. Press to highlight Audio Settings and press ENTER. The Audio Settings page displays. 3. Highlight Mute and press / to select On. 4.
Lan Control Settings allow you to manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network. Configuring the Lan Control Settings If you are in a DHCP environment: 1. 2. 3. 4. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port. Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.
If you are in a non-DHCP environment: English 1. 2. Repeat steps 1-4 above. Projector will restore the latest IP configuration into Lan Control Settings. (*1) Network Network State DHCP Projector IP Address Subnet Mask Default Gateway DNS Apply Disconnect Off 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 Menu 3. 4. 5. 6. 7. 8. Back Press to highlight DHCP and press / to select Off. Contact your ITS administrator for information on the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings.
English The Menu button can also be used to go back to previous OSD menu, exit and save menu settings. ii. To switch input source, click on your desired signal. The tools page allows you to manage the projector, configure the Lan control settings and secure access of remote network operation on this projector. i iii ii iv v i. You can name the projector, keep track of its location and the person in charge of it. ii. You can adjust the Lan Control Settings. iii.
English Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • • • • Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.
English Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu Sub-menu Options Picture Mode Cinema/Dynamic/Standard/User 1/User 2/User 3 Reference Mode Cinema/Dynamic/Standard Brightness Contrast 1. PICTURE: Basic Color Tint Sharpness Flesh Tone Save Settings Reset Picture Settings 2.
Aspect Ratio English Keystone 3. DISPLAY Auto/16:9/4:3/Letter Box/Real Auto Keystone On/Off Keystone Overscan Adjustment Digital Zoom PC & Component YPbPr Tuning Auto/H. Size/Phase/Horizontal position/Vertical position Language Front Table/Rear Table/ Rear Ceiling/Front Ceiling Projector Position Menu position Top-Left/Top-Right/Center/ Bottom-Left/Bottom-Right Menu Display Time 5 sec/10 sec/15 sec/20 sec/25 sec/ 30 sec Menu Settings 4.
Change password Power on Lock Baud Rate 5. SYSTEM SETUP: Advanced Off/On 9600/19200/38400/57600/115200 Test Pattern Closed Caption English Security Settings Off/On Closed Caption Enable Off/On Caption Version CC1/CC2/CC3/CC4 Standby Monitor Out Off/On Control by RS232/RJ45 Network Status DHCP Lan Control Settings Projection IP Address Network Status Subnet Mask Default Gateway DNS Apply 6.
English Description of each menu FUNCTION DESCRIPTION Pre-defined picture modes are provided so you can optimize your Picture Mode projector image set-up to suit your program type. See "Selecting a Reference Mode Brightness 1. PICTURE: Basic menu Contrast Color Tint picture mode" on page 34 for details. Selects a picture mode that most suits your need for the image quality and further fine-tune the image based on the selections listed on the same page below.
English FUNCTION DESCRIPTION Clarity Control See "Adjusting Clarity Control" on page 36 for details. Color Temperature See "Selecting a Color Temperature" on page 36 for details. Color Temperature User_Fine Tuning Gamma Selection See "Selecting a Color Temperature User_Fine Tuning" on page 36 for details. Selects gamma mode that most suits your need for the image quality. See "Selecting a Gamma Selection" on page 36 for details. 2.
English FUNCTION Language Projector Position DESCRIPTION Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 26 for details. The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 14 for details. Menu position Menu Settings Menu display time 4. SYSTEM SETUP: Basic menu Auto Power Off Sets the length of time the OSD will remain active after your last key press.
DESCRIPTION Audio Settings Mute Volume Treble Bass Power On/Off Ring Tone English FUNCTION See "Adjusting the sound" on page 41 for details. Lamp Mode See "Setting Lamp mode as Economic" on page 56 for details. Lamp Settings 5. SYSTEM SETUP: Advanced menu HDMI Settings Reset Lamp Timer See "Resetting the lamp timer" on page 60 for details. Equivalent Lamp Hour See "Getting to know the lamp hour" on page 56 for details on how the total lamp hour is calculated.
English FUNCTION 6. INFORMATION menu (default setting/ value) DESCRIPTION (default setting/value) Source Shows the current signal source. Picture Mode Shows the selected mode in the PICTURE menu. Resolution Shows the native resolution of the input signal. Color System Shows input system format, NTSC, PAL, SECAM, or RGB. Equivalent Lamp Hour Displays the number of hours the lamp has been used. Firmware Version Displays the firmware version of the projector.
English Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust.
English Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows: Total (equivalent) lamp hour = 1 (hours used in Economic mode) + 4/3 (hours used in normal mode) See "Setting Lamp mode as Economic" below for more information on Economic mode. To obtain the lamp hour information: 1.
English Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.benq.com for a replacement lamp. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
English Replacing the lamp • If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp. • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
4. Loosen the screws that secure the lamp. Do not turn the power on with the lamp cover removed. • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries. 5. English • Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
7. Tighten the screws that secure the lamp. English • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 8. Ensure the handle is fully laid flat and locked in place. 9. Replace the lamp cover on the projector. 10. Press the lamp cover down until the click is heard locking the projector. SP 84 11. 0 Restart the projector. Do not turn the power on with the lamp cover removed. Resetting the lamp timer 12.
Light Power English Indicators Status & Description Temp Lamp Power events Orange Off Off Stand-by mode Green Flashing Off Off Powering up Green Off Off Normal operation Orange Flashing Off Off The projector needs to cool for 90 seconds after the power is turned off. Lamp events Orange Flashing Off Red The lamp ignition retries if the lamp fails during startup. Off Off Red 1. 2. The projector needs 90 seconds to cool down. Or Please contact your dealer for assistance.
English Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cable. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
English Specifications Projector specifications All specifications are subject to change without notice. General Product name Model name Digital Projector SP840 Optical Resolution Display system Lens F/Number Lamp 1920 x 1080, 1080p 1-CHIP DMD F = 2.5 to 2.76, f = 23.5 to 28.2mm 330 W lamp Electrical Power supply Power consumption AC100–240V, 50/60 Hz (Automatic) 430W (Max)/ <1W (Standby) Mechanical Dimensions Weight 325 mm (W) x 95 mm (H) x 254 mm (D) 3.54Kg (7.
English Dimensions 325 mm (W) x 95 mm (H) x 254 mm (D) 325 254 95 58.6 80.53 Ceiling Mount Screws: M4 (Max. L=12, Min. L=10) Unit: mm Ceiling Mount Installation 35.7 51.5 80.8 44.0 259.5 71.0 90.5 Tripod Mount 14.0 24.5 14.0 #1/4-20 Max.L=0.3 inch 135.0 160.5 325.8 75.5 157.9 75.5 79.0 132.4 64 Specifications 135.0 124.4 Ceiling Mount M4 x 8 (Max.
English Timing chart Supported timing for COMPUTER input Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 31.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72 37.500 75.000 31.500 VGA_75 43.269 85.008 36.000 VGA_85 37.927 85.039 35.5 720 x 400 x 85 35.2 56.3 36 SVGA_56 37.879 60.317 40.000 SVGA_60 48.077 72.188 50.000 SVGA_72 46.875 75.000 49.500 SVGA_75 53.674 85.061 56.250 SVGA_85 48.363 60.004 65.000 XGA_60 56.
English Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 640 x 480@67Hz 35.000 66.667 30.240 MAC13 832 x 624@75Hz 49.722 74.546 57.280 MAC16 1024 x 768@75Hz 60.240 75.020 80.000 MAC19 1152 x 870@75Hz 68.68 75.06 100.000 MAC21 1024 x 576@60Hz 35.82 60 46.996 1024 x 576-GTF 1024 x 600@60Hz 37.32 60 48.
Video mode Horizontal Frequency (kHz) Vertical Frequency (Hz) English Supported timing for Video and S-Video inputs Color sub-carrier Frequency (MHz) NTSC 15.73 60 3.58 PAL 15.63 50 4.43 SECAM 15.63 50 4.25 or 4.41 PAL-M 15.73 60 3.58 PAL-N 15.63 50 3.58 PAL-60 15.73 60 4.43 NTSC4.43 15.73 60 4.
English Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 49.7 59.8 83.5 WXGA_60 62.8 74.9 106.5 WXGA_75 71.554 84.880 122.500 WXGA_85 63.981 60.020 108.000 SXGA_60 79.976 75.025 135.000 SXGA_75 91.146 85.024 157.500 SXGA_85 1440 x 900 55.935 59.887 106.500 WXGA+_60 1400 x 1050 65.317 59.978 121.750 SXGA+_60 1600 x 1200 75.000 60.000 162.000 UXGA 640 x 480@67Hz 35.000 66.667 30.240 MAC13 832 x 624@75Hz 49.722 74.
English Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).
English Regulation statements FCC statement CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
English Accessibility Requirements for Rehabilitation Act of 1973, Section 508 BenQ's commitment to accessible products allows us to support government in making accessible technology choices BenQ's LCD monitors and projectors are compliant with Section 508 guidelines by including the assistive features as below: • • • • • • • • • • BenQ's monitors have colored "Power" indicators. While the indicator shows green, it means that the monitor is using the full power.
