JoyBook S52 System Disassembly Description Joybook S52 System Disassembly Description 1. Description Joybook S52 Disassembly can be divided into three main parts. To be more efficient, it is better to get to know more about disassembly process. You need the following tools: - Wiha PicoFinish Slotted Screwdriver (Professional Suggestion) z Note: 1. Please turn off Joybook and remove battery before disassemble. 2. The screw for different components may very with size. 3.
JoyBook S52 System Disassembly Description 2. System Disassembly The section discusses at length each major component for disassembly/reassembly and show corresponding illustrations. Use another document “Disassembly Flow Chart” for auxiliary to determine the disassembly sequence for removing components from the notebook. NOTE: Before you start to install/replace these modules, disconnect all peripheral devices and make sure the notebook is not turned on or connected to AC power. 1.1.1 Battery Pack 1.1.
JoyBook S52 System Disassembly Description 1. Modular Components You can easily disassemble “Modular components” (as below indication) no need to disassemble main system.
JoyBook S52 System Disassembly Description 1.1.1 Battery Pack Disassembly 1. Carefully put the notebook upside down. 2. Pull the battery pack out of the compartment ( )while sliding and holding the release lever outwards to the “unlock” ○ position ( n ).
JoyBook S52 System Disassembly Description 1.1.2 HDD Module Disassembly 1. Carefully put the notebook upside down. And remove the battery pack. (Refer to section 2.2.1 disassembly) 2. Remove 2 *(item 24) screws fastening the HDD compartment cover (Figure 2-2), and lift the HDD cover up. (Figure 2-3). 3. Pull the HDD module right forward from the system.
JoyBook S52 System Disassembly Description 4. Refer to step3, remove 4 *(item 23) screws to separate the HDD module from the HDD case. (Figure 2-4).
JoyBook S52 System Disassembly Description 1.1.3 ODD Module (Configuration: DVD & CD-RW Combo/ DVD+RW/ DVD Super-Multi) Disassembly 1. Carefully put the notebook upside down. And remove the battery pack. (Refer to section 2.1.1 disassembly) 2. Put the notebook back to the upright position. Loosen the 3 screws ( ) to release RAM Door. (Figure 2-5). 3. Then insert a small rod, such as a straightened paper clip, into the drive’s manual eject hole and push firmly to release the tray (o).
JoyBook S52 System Disassembly Description ODD Bezel There are 2 kinds of bezel includes of GBAS (Quanta) and KME (Panasonic).
JoyBook S52 System Disassembly Description KME Disassembly 1. Refer to section 2.1.3 (o) step. 2. Remove 3 screws (item 25) as the indication. (Figure 2-7) Figure 2-7 Remove 3 screws GBAS Disassembly 1. Turn the ODD to leftside. And push forward the bezel with tweezers lightly as the indication to release it.
JoyBook S52 System Disassembly Description 1.1.4 DDR-SDRAM Disassembly 1. Refer to section 2.1.3 disassembly ( ) step to remove Door. (Figure 2-9) 2. Pull the retaining clips outwards (n) and remove the DDR-SDRAM from the socket (o).(Figure 2-10) Figure 2-9 Remove the cover first Figure 2-10 Remove the DDR-SDRAM Reassembly To install the DDR, match the DDR's notched part with the socket's projected part and firmly insert the DDR into the socket at 20-degree angle.
JoyBook S52 System Disassembly Description 1.1.5 Wireless Card Disconnect Antenna Disassembly 1. Refer to section 2.1.3 disassembly ( ) step to remove the door. (Figure 2-11) 2. Disconnect 2 wireless card’s antennae first. Then pull the retaining clips outwards. (Figure 2-12) 1. White connect to “AUX” 2.
JoyBook S52 System Disassembly Description 1.1.6 ******* Keyboard Cover/ Keyboard -- Disassembly -1. Refer to 2.1.1.section to remove Battery Pack first. -2. Remove 3 / 1 / 1 screws (Figure 2-13) -3. Reverse the machine to the rear side. Then remove 2 screws. 4. Open the LCD to level plane. Slightly lift up the keyboard cover. (Figure 2-14) Screw type ******* 3screw (item 18) 1 screw (item 19) 1 screw (item 17) 2 screw (item 20.
JoyBook S52 System Disassembly Description Remove 1 / 1 / 1 screws and lift up the K/B Then disconnect the cable to release keyboard.
JoyBook S52 System Disassembly Description Separate (2)System ASSY & (3)LCD Module 1. Refer to 1.1.5 Section to disconnect wireless antenna first. 2. Open the LCD cover to level plane. And disconnect 4 cables (LCD Cable/ VGA Cable/ Touchpad Cable/ Antenna) from the motherboard. Then remove 4 *(item 13) on hinges.
JoyBook S52 System Disassembly Description 2. Put the antenna into the hole of motherboard. Antenna Assembly Notice Please remember let 2 antenna cables to be “parallel” and put into the trench as the picture then fix it with golden type. If not do so, it may will make some issue. 3. Pass through to connect to WLAN Card.
JoyBook S52 System Disassembly Description 2.1 Top Case (with touchpad module & MIC cable) 1. Refer to section 2.1.6 to disassemble keyboard first. Base ASSY 2. Put the notebook upside down. Remove 9*( item7. 8) / 2*(item 2) screws that secure the bottom case. Remove 2 * (item 21) screws in the rear of the notebook..
JoyBook S52 System Disassembly Description How to disassemble “Touchpad” & “MIC cable” from Top Case? case 1. Remove the upper 2* (item 26); lower 2* (item 27) as blue circle of the top case to remove touch pad case Touchpad ( ). Then you can disconnect the touch pad cable ( ). 2. Remove the “MIC cable” refer to red arrow indication.
JoyBook S52 System Disassembly Description 2.2.1 Mother Board 2.2 Base ASSY 1. Refer to section 2.2.1 2. To disconnect 3 cable : L/R speaker cable & bluetooth cable as indication. (Figure 2-21) 3. Remove 4* (item 5) / 2* (item 4) screws. Then Lift up the mother board carefully. (Figure 2-22) Bluetooth Left Speaker cable Please paste the golden type on cable as assembly.
JoyBook S52 System Disassembly Description 2.2.2 Thermal Module/ CPU 1. Reverse the mother board and loosen 3 * (item 1) and disconnect 1 cable. Then can release the thermal module. (Figure 2-23) Thermal Please secure the thermal by the sequence as 1,2,3 indication on the thermal interface. Figure 2-23 release the thermal 2. Loosen the screw by a flat screw driver, upraise the CPU socket to unlock the CPU.
JoyBook S52 System Disassembly Description Refer to 2.2.2 remove thermal and CPU of the M/B.That it will be the M/B Unit.
JoyBook S52 System Disassembly Description How to disassemble PCMCIA from M/B? 1. Remove the 2 *(item 28) screws that secure the PCMCIA then reverse M/B to another side. (Figure 2-25) 2. Remove PCMCIA carefully refer to red indication with flat screwdriver. (Figure 2-26) Figure 2-26 push from inner to outer with flat screwdriver as indication Disassembly PCMCIA Notice Figure2-25 remove 2 screws Be careful not to push the HDD connector’s pin too strongly.
JoyBook S52 System Disassembly Description 2.2.3 CRT PCB Module Disassembly 1. Refer to 2.2.3 to remove M/B. CRT Cable CRT PCB 2. Remove 1*(item 3) / 2 hex nuts (item 9) and disconnect the cable as the blue arrow to remove VGA cable and VGA board. (Figure 2-26) Assembly Notice: Please arrange the cable by the trench road of the case as picture.
JoyBook S52 System Disassembly Description 2.2.4 Bluetooth Module Disassembly 1. Refer to 2.2.3 to remove M/B. 2. Remove 2 * (item 2) then detach Bluetooth Module.
JoyBook S52 System Disassembly Description 2.2.5 Speakers Disassembly 1. Refer to 2.2.3 to remove M/B. 2. Remove 2* (item 29) screws then detach the right and left speakers.
JoyBook S52 System Disassembly Description 2.2.6 Bottom Case 1. Refer to section 2.2.4, 2.2.5, 2.2.6 to remove all components on Bottom case. You will get bottom case.
JoyBook S52 System Disassembly Description 3. LCD Module 1. Refer to section 2.1.6 to separate LCD module.
JoyBook S52 System Disassembly Description 3.1.1 LCD Bezel Disassembly 1. Refer to section 3.1 2. Remove the rubber 7 pads and 7 * (item 12) screws on the corners of the panel. (Figure 2-30) 3. Remove LCD Bezel by hand.
JoyBook S52 System Disassembly Description 3.1.2 LCD Inverter/ Bracket/ Panel/ FFC Disassembly 1. Remove the 6* (item 11) screws of LCD panel. (Figure 2-31) 2. Disconnect 2 cable from the inverter board to detach inverter.
JoyBook S52 System Disassembly Description 2. Remove the 4 *(item 10) screws to remove the LCD bracket on side of the LCD panel. (Figure 2-33) Figure 2-33 LCD Bracket 3. Reverse the LCD panel. To tear open the silver tinfoil and remove LCD FFC.
JoyBook S52 System Disassembly Description 3.1.3 LCD Cover Module Disassembly 1. Completion of 3.1.1 disassembly section. You can get LCD Cover Module. It includes of Antenna and LCD Support.
JoyBook S52 System Disassembly Description How to disassemble LCD Support / Wire Antenna from “LCD cover module”? 1. Refer to section 3.1.2. 2. Release 6 * (item 30) as the arrow on support to remove “LCD support” . (Figure 2-36) and lift all type to remove “wire antenna with bracket”.