OW NER/OP ERAPERATOR TOR WNER /O MAANUAL NUAL MOODELS DELS 705 705S 705&&705S TEENDERIZER NDERIZER NOTICIA IMPORTANTE Este manual contiene importantes instrucciones de seguridad que deben ser seguidas el pie de la letra cuando utilice esta maquina. IMPORTANT NOTICE This manual contains Important Safety Instructions which must be strictly followed when using this equipment.
BEFORE USING THIS EQUIPMENT Berkel’s tenderizers are designed to tenderize/slice meat and other food products safely and efficiently. However, unless the operator is properly trained and supervised, there is the possibility of a serious injury. It is the responsibility of the owner to ensure that this tenderizer is used properly and safely, strictly following the instructions contained in this manual and any requirements of local law.
TABLEOFCONTENTS Page General Safety Instructions .............................................................................................................. 2-3 Equipment Identification ..................................................................................................................... 4 Intended Uses ...................................................................................................................................... 5 Safety Characteristics ............................
PELIGRO CUCHILLA FILOSA para evitar serios accidentes a su persona siga las instrucciones de este manual y 1. NUNCA utlice esta mçquina sin previa instrucciùn y autorizaciùn de su supervisor. 2. LA MáQUINA DEBE apoyarse sobre un nivel solido y plano. 3. LOS PROTECTORES deben colocarse ANTES de enchufar y operar la máquina. 4. SIEMPRE utilice el enchufe original proveido por el fabricante. 5. SIEMPRE utilice el utensillo para empujar la comida - nunca su mano. 6.
WARNING SHARP KNIFE BLADE to avoid serious personal injury follow all the instructions in this manual and 1. NEVER touch this machine without training and authorization by your supervisor. 2. MACHINE MUST BE on solid level support. 3. GUARDS MUST BE in place before plugging in and turning on machine. 4. ALWAYS use three pronged plug provided. 5. ALWAYS use food pusher not your hand. 6. NEVER TOUCH ROTATING KNIFE. 7. KEEP hands, arms, hair and loose clothing clear of all moving parts. 8.
EQUIPMENT IDENTIFICATION Safety Cover Clutch Gear Blade and Frame Assembly Locking Lever ON/OFF Switch 4 • 705 & 705S OWNER /OPERATOR MANUAL
INTENDED USES The 705 and 705S tenderizers are designed for processing the following types of food products: • • • • Beef Poultry Pork Vegetables The following items are not suitable to be processed on the 705 and 705S tenderizers: • • • Products on/with bones Frozen products Non-food products SAFETY CHARACTERISTICS • • • The cover is equipped with a safety interlock that will not allow the tenderizer to be turned on unless the cover is in the down position.
WARNING FOR PERSONAL SAFETY, THIS TENDERIZER WILL NOT OPERATE WITHOUT THE SAFETY NECK IN PLACE. NEVER RAISE OR LOWER THE SAFETY NECK WITH THE MACHINE TURNED ON, BOTH FOR PERSONAL PROTECTION AND MACHINE PROTECTION. ALWAYS TURN MACHINE OFF WHEN NOT IN USE. ONLY RUN MACHINE BY USING THE ON/OFF SWITCH, NEVER BY RAISING OR LOWERING THE COVER. 5. Uncoil power cord and plug into a grounded, approved outlet. (Specifications for this machine are found on the serial plate located on the left-hand leg.) 6.
. All removable parts can be soaked and scrubbed using a bristled brush and good quality detergent approved for food processing equipment. 10. Rinse thoroughly and set aside to air dry while you are washing the machine case. 11. Sanitize all blade and frame assembly parts and tenderizer unit. REASSEMBLY 1. Replace stripper plates with solid flanges to the outside of the assembly, teeth to the center and pointing up. (Front and back stripper plates for the tenderizer group are interchangeable.) 2.
MODELS Model 705: Tenderizer (includes tenderizer blade and frame assembly). Model 705S: Stir-Fry Cutter (includes stir-fry cutter blade and frame assembly). ModelSFC: Stir-Fry Blade and Frame Assembly (to convert 705 and earlier model Berkel to optional stir-fry cutter use). TROUBLESHOOTING Should your tenderizer fail to function properly, here are a few things you can check before calling a Designated Berkel Service Location for service. Product not tenderizing or slicing properly: 1.
REPAIR PARTS/REPAIR SERVICE Please contact your Designated Berkel Service Location for any repair parts and/or repair service required on your Berkel tenderizer. Additional information may be obtained from: Service Support Center Berkel Company 4406 Technology Drive South Bend, Indiana 46628-9700 574/232-8222 · Fax 574/232-8116 (800) 348-0251 SPECIFICATIONS Motor: 1/2hp, 115 volt, 60 cycle single phase, 7.
WARRANTY Berkel Company (“Berkel”) warrants to the Buyer of new equipment that said equipment, when installed in accordance with our instructions and subjected to normal use, is free from defects in material or workmanship for a period of one (1) year from the date of sale.1 BERKEL SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
