OWNER/OPERATOR MANUAL MODEL E-222 GRINDER NOTICIA IMPORTANTE Este manual contiene importantes instrucciones de seguridad que deben ser seguidas el pie de la letra cuando utilice esta maquina. 12 • E-222O WNER/OPERATOR MANUAL IMPORTANT NOTICE This manual contains Important Safety Instructions which must be strictly followed when using this equipment.
BEFORE USING THIS EQUIPMENT Berkel’s grinders are designed to chop meat and other food products safely and efficiently. However, unless the operator is properly trained and supervised, there is the possibility of a serious injury. It is the responsibility of the owner to ensure that this grinder is used properly and safely, strictly following the instructions contained in this manual and any requirements of local law. No one should use or service this grinder without proper training and supervision.
TABLE OF CONTENTS Page General Safety Instructions .............................................................................................................. 2-3 Equipment Identification ......................................................................................................................4 Installation ............................................................................................................................................5 Operating Instructions ......................
PELIGRO CUCHILLA FILOSA para evitar serios accidentes a su persona siga las instrucciones de este manual y 1. NUNCA toque esta maquina sin la capacitacion adequada, ni sin autorizaciùn de su supervisor. 2. SIEMPRE vea que la base del recipienta este bien atornillada y bien apretada. 3. LOS PROTECTORES deben estar en su lugar ANTES de enchufar y conectar la máquina. 4. USE SIEMPRE el enchufe de tres clavijas suministrado. 5. NUNCA use nada mas ademas que el prensador para alimentar la maquina. 6.
WARNING SHARP KNIFE BLADE to avoid serious personal injury follow all the instructions in this manual and 1. NEVER touch this machine without training and authorization by your supervisor. 2. ALWAYS check to see that all bowl mounting screws are in position and tight. 3. GUARDS MUST BE in place before plugging in and turning on machine. 4. ALWAYS use three pronged plug provided. 5. NEVER use anything but the rammer to feed product into the grinder. 6.
EQUIPMENT IDENTIFICATION Rammer Tray On/Off Switch Safety Guard Hopper Ring Plate Knife Feedscrew Thumb Screw 4 • E-222 OWNER /OPERATOR MANUAL Thrust Washer Fiber Washer
INSTALLATION SITESELECTION Select a solid, level surface to install the E-222 chopper. This area should be well lit and large enough to allow easy access to all sides of the machine. ELECTRICAL Your E-222 chopper is manufactured with a 20-amp power cord and plug. Contact a licensed electrician to install a 20-amp outlet. Do not try to modify a standard outlet to accommodate this plug. Failure to use a correct outlet will void the warranty.
4. Unscrew the ring from the cylinder. Place the knife, plate surface out, onto the feedscrew, mating the square hole with the square shaft. Insert the plate over the knife with the flat edge mating with the pin in the cylinder. Screw the ring onto the body, but do not over tighten. The fineness of the cut is determined by the size of the holes in the plate, not the tension of the ring. Over tightening the ring will cause the knife and plate to wear and the motor to overheat.
CLEANINGANDSANITIZING DISASSEMBLY 1. Unplug the chopper and remove the rammer. 2. Loosen the ring but don’t remove it. Loosen the thumbscrew and remove the entire cylinder. Take the cylinder to the sink. Unscrew the ring and pull off the plate, knife and feedscrew. Thoroughly clean each of these parts in hot water using a food grade detergent. Rinse and sanitize each part with an USDA approved sanitizer. Remember to keep the knife and plate together as a pair.
7. Plug the chopper in and run for one second. Turn off the chopper and check to see if the ring is tight. If it is loose, then tighten it. Your chopper is now ready to operate. MAINTENANCE The knives and plates should be kept together as a matched set. Failure to do so will result in mismatched cutting surfaces, which will lower productivity and product quality. When the knife becomes dull, have it and its matching plate sharpened together.
SPECIFICATIONS MOTOR 115/60/1, 1hp, 18 amp CAPACITY 15 to 20 pounds/minute (7 to 9 kg/min.) SPEED 235 rpm WEIGHT Net Shipping DIMENSIONS Height Width Length 100 lbs. (45.5 kg) 106 lbs. (48 kg) OVERALL 18 ¼” (464mm) 15 ¾” (400mm) 28 ½” (724 mm) FOOTTOFOOT 10 ½” (267mm) 16 ½” (419mm) TRAY 26 ½ ”, (673mm) 15 ½” (394mm) 3” (76mm) PARTS KNIFE K-04022-2 PLATES 1/8” (3.2mm) 3/16” (4.8mm) 1/4” (6.3mm) 3/8” (9.
WARRANTY Berkel Company (“Berkel”) warrants to the Buyer of new equipment that said equipment, when installed in accordance with our instructions and subjected to normal use, is free from defects in material or workmanship for a period of one (1) year from the date of sale.1 BERKEL SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.