3M™ Anti-Fatigue Mats 9900 Series User’s Guide 1
Table of Contents Section Page Safety Information.................................................................................................3 1.0 Installation of 3M™ Anti-Fatigue Mats 9900 and 9920....................................5 2.0 Installation and Assembly of 3M™ Anti-Fatigue Mat Runner 9910.................6 3.0 Optional Permanent Bonding of Runner Sections with Adhesive...................8 4.0 Cleaning Guidelines..............................................................................
SAFETY INFORMATION Read, understand, and follow all safety information contained in these instructions prior to installation and use of the 3M™ Anti-Fatigue Mats 9900 Series. Retain these instructions for future reference. Intended Use Anti-Fatigue Mats are intended for use in electronic/electrical assembly facilities requiring conductive floor matting for control of static electricity. They are intended for use in an indoor environment and not intended for use where insulating matting is required.
WARNING: To reduce the risk associated with hazardous voltage due to 3M™ Anti-Fatigue Mats 9900 Series being used in areas requiring insulating type matting: • Anti-Fatigue Mats are electrically conductive – do not use these mats in areas with possible exposure to high voltage. To reduce the risk associated with hazardous voltage due to Anti-Fatigue Mats being installed with an incorrect grounding lead: • Do not use Anti-Fatigue Mats without using the correct grounding cord, 3M™ Ground Cord 3040.
1.0 Installation of 3M™ Anti-Fatigue Mats 9900 and 9920 WARNING: To reduce the risk associated with hazardous voltage due to Anti-Fatigue Mats 9900 Series being used in areas requiring insulating type matting: • Anti-Fatigue Mats are electrically conductive – do not use this matting in areas with possible exposure to high voltage.
2.0 Installation and Assembly of 3M™ Anti-Fatigue Mat Runner 9910 WARNING: To reduce the risk associated with hazardous voltage due to Anti-Fatigue Mats 9900 Series being used in areas requiring insulating type matting: • Anti-Fatigue Mats are electrically conductive – do not use this matting in areas with possible exposure to high voltage.
4. Kneel or squat on the first section of the 3M™ Anti-Fatigue Mat Runner 9910 Series with the connector tabs in front of you and pull the next runner section towards you until its edges aligns with the edge of the first runner section. (Figure 5) 5. Drop it in place so the tubular cells of the second section fit into the connector holes on the tabs of the first section.
3.0 Optional Permanent Bonding of Runner Sections with Adhesive WARNING: To reduce the risk associated with back strain due to the heavy weight of the mats: • Follow safe lifting procedures during installation or moving. Note: Permanent adhering of the runner sections together with an adhesive may create a continuous runner that is very heavy and difficult to move or reposition.
4. As necessary, apply localized pressure to close the adhered seam of the 3M™ Anti-Fatigue Mat Runner 9910 Series. It may be necessary to hold pressure for 10-15 seconds until the adhesive bonds the two pieces. (Figures 6 & 7) Figure 6 Figure 7 5. The beveled edges of the seam are adhered separately. Pull the beveled edge up to expose its edge and apply adhesive then push the two beveled edges of the adhered sections together. (Figures 8 & 9) Figure 8 Figure 9 6.
4.0 Cleaning Guidelines WARNING: To reduce the risk associated with back strain due to the heavy weight of the mats: • Follow safe lifting procedures during installation or moving. To reduce the risk associated with foot slip hazards due to improper maintenance: • Follow proper cleaning procedures as outlined in this instruction manual. • Do not use paste wax or vinyl cleaners. • Do not treat the mat surface with any protective films or floor finishes.
• For small mat areas apply the cleaner with a trigger spray bottle. Scrub and remove excess liquid from the mat surface with a dampened sponge or lintfree cloth. • For larger mat areas apply the cleaner with a mop and bucket. To reduce film build-up change out the cleaning solution frequently. Note: It is not necessary to rinse the mat surface. 5.
6.0 3M™ Anti-Fatigue Mats 9910 Series Specifications Part Number Description 3M ID Number 9900 3 ft. x 5 ft. (0.9 m x 1.5 m) Anti-Fatigue Mat 98-0798-5635-1 9900 2 ft. x 3 ft. Anti-Fatigue Mat 98-0798-5748-2 9910 3 ft. x custom length Anti-Fatigue Mat Runner 98-0798-5636-9 9920 22 in. Anti-Fatigue Mat, Octagonal Shape 98-0798-5674-0 One 3M™ Ground Cord 3040, 15 ft. (4.6 m) is included with each mat. Property Typical Value Size Standard: 3 ft. x 5 ft. (0.9 m x 1.5 m) , 2 ft. x 3 ft. (0.
3M is a trademark of 3M Company. Other trademarks used herein are the properties of their respective owners. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use.