DIGITALES THERMOSTAT DIGITAL THERMOSTAT THERMOSTAT NUMÉRIQUE TERMOSTATO DIGITALE MONTAGEANLEITUNG - I / 2018 ASSEMBLY INSTRUCTIONS / NOTICE DE MONTAGE / ISTRUZIONI DI MONTAGGIO
HT01 Platzierung des Bodensensors Der Bodensensor sollte in einem zugelassenen nicht leitenden Installationsrohr gemäß EN 61386-1 installiert werden, das in den Boden eingelassen ist. Der Bodensensor sollte in gleichen Abständen zwischen zwei Läufen des Heizelements angeordnet sein, wobei die Spitze mindestens 300 mm von der Außenkante des Heizelements entfernt sein muss. Das mitgelieferte Sensorkabel kann mit einem separaten Kabel bis zu 50 m verlängert werden.
HT01 Technische Daten Spannung: AC230V ± 10% 50/60 Hz Leistungsaufnahme: 5W Einstellungsbereich: 5 ~ 30ºC Bodenüberhitzung Schutz: 30 ~ 80°C (werkseitig auf 65°C eingestellt) Schutzgehäuse: IP20 Gehäusematerial: ABS + PC feuerbeständig Zertifizierung: CE Bodensensor: Gummi-Thermoplast NTC 10K Sensor Interner Sensor: NTC 10K Sensoren Auswahl Der Thermostat ist werkseitig auf die Verwendung der Raum- und Bodentemperatursensoren voreingestellt. Die folgenden Optionen sind verfügbar.
HT01 7 Tage Automatikmodus Um den 7-Tage-Timer-Modus auszuwählen, drücken Sie M, bis auf dem LCD-Bildschirm angezeigt wird. Der Thermostat schaltet dann zwischen Komfort- und Energiesparmodus (Ein / Aus) automatisch gemäß den Datums- und Uhrzeiteinstellungen. Jeder Wochentag kann mit individuellen Einstellungen versehen werden. Um den automatischen Modus einzurichten, drücken und halten Sie auszuwählen, der eingestellt werden soll, drücken Sie . 3 Sekunden lang.
HT01 Mounting of the floor sensor The floor sensor should be installed within an approved non conductive installation pipe in accordance with EN 61386-1, which is embedded in the floor. The pipe (flexible conduit) should be placed as high as possible in the subfloor. The floor sensor should be located equidistant between two runs of the heating element with the tip at least 300mm away from the outside edge of the heater.
HT01 Technical Data Voltage: AC230V ± 10% 50/60HZ Power Consumption: 5W Setting Range: 5 ~ 30ºC Floor overheating Protection: 30 ~ 80˚C (factory set @ 65˚C) Protective housing: IP20 Housing Material: ABS + PC fire-resistant Certification: CE Floor Sensor: Rubber-Thermoplastic NTC 10K Sensor Internal Sensor: NTC 10K Sensor Selection The thermostat is factory preset to use the room and floor temperature sensors. The following options are available. To change, press M for 3 seconds then M once more.
HT01 7 Day Automatic mode To select the 7 day timer mode press M until is displayed on the LCD screen. The thermostat will then switch between comfort & energy saving mode (On/Off) automatically according to the day & time settings. Each day of the week can be programmed with individual settings. To set up the automatic mode, press & hold for 3 seconds. To select the day of the week to be programmed press . The bottom of the screen will show the following pattern of 24 numbered surfaces.
HT01 Mounting of the floor sensor The floor sensor should be installed within an approved non conductive installation pipe in accordance with EN 61386-1, which is embedded in the floor. The pipe (flexible conduit) should be placed as high as possible in the subfloor. The floor sensor should be located equidistant between two runs of the heating element with the tip at least 300mm away from the outside edge of the heater.
HT01 Technical Data Voltage: AC230V ± 10% 50/60HZ Power Consumption: 5W Setting Range: 5 ~ 30ºC Floor overheating Protection: 30 ~ 80˚C (factory set @ 65˚C) Protective housing: IP20 Housing Material: ABS + PC fire-resistant Certification: CE Floor Sensor: Rubber-Thermoplastic NTC 10K Sensor Internal Sensor: NTC 10K Sensor Selection The thermostat is factory preset to use the room and floor temperature sensors. The following options are available. To change, press M for 3 seconds then M once more.
HT01 7 Day Automatic mode To select the 7 day timer mode press M until is displayed on the LCD screen. The thermostat will then switch between comfort & energy saving mode (On/Off) automatically according to the day & time settings. Each day of the week can be programmed with individual settings. To set up the automatic mode, press & hold for 3 seconds. To select the day of the week to be programmed press . The bottom of the screen will show the following pattern of 24 numbered surfaces.
HT01 Mounting of the floor sensor The floor sensor should be installed within an approved non conductive installation pipe in accordance with EN 61386-1, which is embedded in the floor. The pipe (flexible conduit) should be placed as high as possible in the subfloor. The floor sensor should be located equidistant between two runs of the heating element with the tip at least 300mm away from the outside edge of the heater.
HT01 Technical Data Voltage: AC230V ± 10% 50/60HZ Power Consumption: 5W Setting Range: 5 ~ 30ºC Floor overheating Protection: 30 ~ 80˚C (factory set @ 65˚C) Protective housing: IP20 Housing Material: ABS + PC fire-resistant Certification: CE Floor Sensor: Rubber-Thermoplastic NTC 10K Sensor Internal Sensor: NTC 10K Sensor Selection The thermostat is factory preset to use the room and floor temperature sensors. The following options are available. To change, press M for 3 seconds then M once more.
HT01 7 Day Automatic mode To select the 7 day timer mode press M until is displayed on the LCD screen. The thermostat will then switch between comfort & energy saving mode (On/Off) automatically according to the day & time settings. Each day of the week can be programmed with individual settings. To set up the automatic mode, press & hold for 3 seconds. To select the day of the week to be programmed press . The bottom of the screen will show the following pattern of 24 numbered surfaces.
HT01 ERKLÄRUNG Die Bedienungsanleitung dient nur als Referenz. Diese Anleitung kann abweichende Angaben enthalten. Die beschriebenen Produkte können jederzeit aktualisiert werden. Die Zeichnungen in dieser Anleitung dienen nur zur Darstellung und haben keinen Anspruch auf Aktualität. STATEMENT This instructions should only be considered as a standard manual. Modifications applied to updated version of the product might not be mentioned inside this document.
