MSDS

ManualsBrandsBernzomatic ManualsTools & HardwareSpecialty Solder Kit

Rev 005

Date: 2/19/07

M/L 1114

MATERIAL SAFETY DATA SHEET CODE M/L 1114

This Material Safety Data Sheet complies with the OSHA

Hazard Communication Standard 29CFR 1910.1200

PRODUCT: BERNZOMATIC LEAD-FREE SILVER BEARING SOLDER; TIN/COPPER/SILVER

ACID CORE SOLDER ALLOYS (TCI-107-1)

COMMON NAME OF SYNONYMS: TIN/COPPER/SILVER FORMULATION (<1% SILVER CONTENT) SOLDERS OR ALLOYS

IN THE FOLLOWING FORMS: WIRE WITH ACID FLUX CORE.

________________________________________________________________________________________________________

NFPA/HMIS HAZARD CODES: HEALTH: 1/1 FIRE: 0/0 REACTIVITY: 0/0 SPECIAL: NA

------------------------------------------------------------------------------------------------------------------------------------------------------------------------

0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe

SECTION I

MANUFACTURERS NAME: Lenox ISSUE DATE: October 2004

1690 Lowery Street

Winston-Salem, NC 27101

336-777-8600

INFORMATION PHONE: 800-654-9011

SECTION II HAZARDOUS INGREDIENTS

INGREDIENT

CAS NO.

US-NIOSH

RTECS NO.

US OSHA

PEL

ACGIH

TLV

APPROX.

VOL. %

(*1)

WT.

PERCENT

(*2)

SOLDER

COMPONENTS

>>>>>>>>>>

>>>>>>>>>

97.0

Tin

7440-31-5

XP7320000

2.0mg/mg3

Balance

Copper

(dust)

(fume)

7440-50-8

GL5325000

1.0mg/mg3

0.1mg/m3

1.0mg/mg3

0.1mg/m3

3.0 – 4.0

Silver

CORE

7440-22-4

COMPONENTS

VW3500000

>>>>>>>>>>

0.01 mg/m3

>>>>>>>>>

0.1 mg/m3

>>>>>>>>

2.0-2.5

(*3)

Urea

57-13-6

2.55

(*4)

2.6

NOTES: *1-Product volume formulation is relatively constant.

*2-Product weight formulation is to customer specification and appears on product packaging or packing slip.

*3-Remaining constituents, by volume, are inert or constitute less than the declaratory reporting threshold.

NE=NONE ESTABLISHED AL=ACTION LEVEL PEL=PERMISSIBLE EXPOSURE LIMIT TLV=THRESHOLD LIMIT VALUE

SECTION III PHYSICAL DATA

APPEARANCE & ODOR (AT NORMAL CONDITIONS): Solid - Silver to silver-gray metallic metal-No odor: Contains core of white

powder.

SPECIFIC GRAVITY (H20=1): No information available

MELTING POINT RANGE (DEGREES F): 227-250 (441-482 Degree F)

BOILING POINT (DEGREES C): No information available

SOLUBILITY IN WATER: Insoluble

Summary of content (4 pages)

PAGE 1
MATERIAL SAFETY DATA SHEET CODE M/L 1114 This Material Safety Data Sheet complies with the OSHA Hazard Communication Standard 29CFR 1910.1200 PRODUCT: BERNZOMATIC LEAD-FREE SILVER BEARING SOLDER; TIN/COPPER/SILVER ACID CORE SOLDER ALLOYS (TCI-107-1) COMMON NAME OF SYNONYMS: TIN/COPPER/SILVER FORMULATION (<1% SILVER CONTENT) SOLDERS OR ALLOYS IN THE FOLLOWING FORMS: WIRE WITH ACID FLUX CORE.
PAGE 2
SECTION IV FIRE & EXPLOSION HAZARD DATA FLASH POINT: FLAMMABLE LIMITS: EXTINGUISHING MEDIA: SPECIAL FIRE FIGHTING PROCEDURES: UNUSUAL FIRE & EXPLOSION HAZARDS: Non-Flammable Not Applicable No specific agents available If involved in fire, use full protective clothing and NIOSHA/MSHA approved selfcontained breathing apparatus operated in a positive-pressure mode. The solid metal form is not a fire hazard. However, dust generated from processing operations may present a moderate fire or explosion hazard.
PAGE 3
EYE PROTECTION: OTHER PROTECTIVE EQUIPMENT: WORK/HYGIENIC PRACTICES: Safety glasses or goggles are recommended where the possibility exists of getting dust particles in the eyes. Safety glasses or goggles with face shield are recommended around molten metal. Safety equipment should be worn as appropriate for the work environment. Do not permit eating, drinking, or the use of cosmetics or tobacco products while handling or processing material or in solder work areas.
PAGE 4
CHEMICAL NAME RQ (LBS) Copper 5000 (*1) -FOOTNOTES*1= Reportable quantity (RQ) under CERCLA Section 302. Spills to the environment exceeding the reportable quantity in any 24hour period must be reported to the U.S. National Response Center (800) 424-8802. No reporting of releases of the hazardous substance(s) is required if the diameter of the pieces of the solid metal(s) released is equal to or exceeds 100 micrometers (0.004 inches).