Dishwasher Installation Instructions DW 24XT/DW 24XV
Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT– Observe all Dishwasher IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately contact your dealer or builder. governing codes and ordinances. • Note to Installer – Be sure to leave these instructions for the consumer’s and local inspector’s use.
Installation Preparation PARTS SUPPLIED: Four flat head wood screws to secure dishwasher to underside of countertop (in literature package). Screw type hose clamps and one drain hose. 2 top mounting cl\ips.
Installation Preparation • The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the enclosure. CLEARANCES: When installed into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8" min. clearance from the front of the dishwasher for door opening.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. 1-1/2" Dia. Hole (Max.) 2½~3½ in. (65 ~ 90mm) Electrical Requirements • This appliance must be supplied with 120V, 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
Installation Instructions PREPARE HOT WATER LINE CAUTION: • The line may enter from either side, rear or floor within the shaded area shown in Figure F. • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole. Opening the door will cause the dishwasher to tip forward.
Installation Instructions STEP 4 INSTALL POWER CORD STEP 2 ADJUST LEVELING LEGS Skip this step if dishwasher will be direct wired. Use power cord kit WX09X70910 available for purchase from an authorized parts dealer. The power cord and connections must comply with local codes and ordinances. • Recommended power cord length is 54" min. and 64" max. • Move the dishwasher close to the installation location and lay it on its back.
Installation Instructions STEP 6 INSTALL DRAIN HOSE STEP 8 SLIDE DISHWASHER PARTIALLY INTO CABINET • Install the screw type hose clamps to the drain hose. • Install the drain hose to the drain hose installation hose, then tighten the screw type hose hose. DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. • Slide dishwasher into the opening a few inches at a time. Do Not Push Against Front Door Panel With Knee. Damage to The Door Panel Will Occur.
Installation Instructions STEP 9 POSITION DISHWASHER UNDER COUNTERTOP Reposition Dishwasher by Grasping Both Sides With Hands • Check to be sure that wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs. Check by opening and closing the door. • Push dishwasher into cabinet.
Installation Instructions Open the door remove the tub cap on both sides of the tub. Install screw through the dishwasher side hole to the wall of cabinet. Reinstall tub cap. STEP 11 SECURE DISHWASHER TO CABINET Method 1: To install using Top Mount Cabinet Clips. Depending on the depth of cabinet,the Top Mount Clip have a break off point that can be removed if necessary. The dishwasher must be secured to the countertop.
Installation Instructions STEP 13 CONNECT DRAIN LINE DRAIN LINE INSTALLATION FOLLOW ALL LOCAL CODES AND ORDINANCES. • Connect drain line to air gap, waste tee or disposer using either previously determined method. The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or disposer. Cut on the marked line as required for your installation.
Installation Instructions STEP 14 CONNECT POWER SUPPLY STEP 15 PRE-TEST CHECKLIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. Skip this step if equipped with power cord. Verify that power is turned off at the source. • Remove junction box cover “A”. • Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box “B”.
Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK Turn on power supply (or plug power cord into outlet, if equipped). Turn on your dishwasher (please refer to the Owner's Manual for instructions). Close door, select RINSE ONLY cycle and press START/CANCEL. . Check to be sure that water enters the dishwasher If water does not enter the dishwasher, check to be sure that water and power are turned on. Check for leaks under the dishwasher.
CALIFORNIA PROPOSITION 65 WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov. ADVERTENCIA: Cáncer y Daño Reproductivo – www.P65Warnings.ca.gov. AVERTISSEMENT: Cancer et Troubles de l’appareil reproducteur – www.P65Warnings.ca.gov.
