BERTAZZONI INSTALLATION MANUAL 30” ELECTRIC DOUBLE BUILT-IN OVEN 3100574 WWW.BERTAZZONI.
/ Table of contents TABLE OF CONTENTS WARNINGS ___________________________________________________________________ DATA RATING LABEL ___________________________________________________________ BEFORE INSTALLATION ________________________________________________________ Room ventilation______________________________________________________________ Cabinet requirement___________________________________________________________ Installing the oven in the unit____________________________________________________
/ Models Models Models PROF30FDEXT PROF30FDEXV MAST30FDEXT MAST30FDEXV 3
/ Warnings WARNINGS To ensure proper and safe operation, the appliance must be properly installed and grounded by a qualified technician. DO NOT attempt to adjust, repair, service, or replace any part of your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified servicer. FOR THE INSTALLER: Before installing the Bertazzoni appliance, please read these instructions carefully.
/ Warnings/ Data rating label DO NOT lift the applince by the oven door’s handle, as this may damage the door hinges and cause the door to fit incorrectly. DO NOT lift the appliance by the appliance’s control panel. The unit is heavy and should be handled accordingly. Proper safety equipment such as gloves and adequate manpower of at least two people must be used in moving the appliance to avoid injury and to avoid damage to the unit or the floor.
/ Before installation BEFORE INSTALLATION • This appliance shall only be installed by an authorized professional. If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the socket cable section is suitable for the electricity drawn by the oven. • This appliance shall be installed in accordance with the manufacturer’s installation instructions.
/ Ventilation preparation / Specifications IMPORTANT INFORMATION INSTALLING THE OVEN IN A CABINET Ensure that the oven is fully present and undamaged after removing all loose parts from their inner and outer packaging. In the event of any uncertainty, do not use the appliance and contact technical support. Check that the kitchen unit is suitable for installation of the oven, referring to the dimensions given in this guide.
/ Before installation Finish the edges of the opening because they may be visible when the door is open. The clearance between the oven and the kitchen units must be enough to ensure sufficient ventilation and air discharge. BEFORE INSTALLATION INSTALLING THE OVEN APPLIANCE HOUSING IN A TALL The oven can be installed in a standard or flush application.
/ Before installation BEFORE INSTALLATION Flush installation TOP VIEW 4" x 28 1/2" (102 x 724) AIR INTAKE CHANNEL SECTION 23 7/8" 606 FLUSH INSET DEPTH (a) (a) 1" 25 SIDE VIEW FRONT VIEW 30 1/2" 774 FLUSH INSET WIDTH 28 1/2" 724 1" 25 3/4" 18 1" 25 53 7/8" 1367 FLUSH INSET HEIGHT 53" 1346 (b) AIR RECIRCULATION 1" 25 1/8" 3 (b) VENTILATION GRID (a) Spacers – Included with appliance (b) Visible Area – Match finish to outside cabinet panels 9
/ Installation requirements / Electrical connection INSTALLATION REQUIREMENTS ELECTRICAL CONNECTION ELECTRICAL Warrning! A properly-grounded horizontally- mounted electrical receptacle should be installed no higher than 3” (7.6 cm) above the floor, no less than 2” (5 cm) and no more than 8” (20,3 cm) from the left side (facing product). Check all local code requirements. ELECTRICAL SHOCK HAZARD Disconnect electrical power at the circuit breaker box or fuse box before installing the appliance.
/ Installation requirements / Electrical connection FOUR-WIRE CONN.RECEPTACLE NEMA 14-50R Power supply Black wires Junction box White wires UL-listed wire connectors Red wires Green wires Flexible metal conduit from oven UL or CSA listed connector Check your local code for which of the options below should be used in grounding the receptacle power supply connections.
/ Wiring diagram WIRING DIAGRAM The electric wiring diagrams and schematics are attached behind the range, and should not be removed except by a service technician, then replaced after service. 30” XT EO WR &1 RU / - 7 WR &1 EO / - EO 8 7 EX WR > @ Empty WR &1 EO YL UH UH JU YL WR &9 8& > @ WR &9 /& WR &1 WR &1 JU 3& > @ EO %3 '; WR &1 76 WR &1 9 %3 6; 3 Empty 0 RU EX ZK J\ ,/ ZK 5/ 4/ %$&.
/ Wiring diagram 30” XV 13
/ Installation INSTALLATION APPLIANCE INSTALLATION Unpacking the oven To avoid risk of severe personal injury and damage to the unit and flooring; this appliance requires two or more personnel while handling and moving.
/ Installation REMOVING THE OVEN DOOR Prepare the door for removal. Flip up the locking clamps on each door hinge. Slowly shut the door until the protruding clamps stop the movement. Pull oven door upwards and remove. Do not lift or carry the oven door by its handle! This may damage the hinges. The oven door is heavy and fragile. Use both hands to remove the oven door. The door front includes glass components. Handle carefully to avoid breaking. Grasp only the sides of the oven door.
/ Installation checklist / final preparation INSTALLATION CHECKLIST A qualified installer should carry out the following checks: FINAL PREPARATION • • Make sure the clearance to cabinet surfaces curresponds to manufacturers guidelines. • Make sure the oven is level and securely fitted to the cabinet. • Check that lower trim is undamaged. Open the (lower) oven door slowly until it is fully open and check for adequate clearance between the bottom of the door and the lower trim.
/ Bertazzoni service BERTAZZONI SERVICE Bertazzoni is committed to providing the best customer and product service. We have a dedicated team of trained professionals to answer your needs. If you own a Bertazzoni appliance and need service in the US or Canada please use the following contact information: e-mail: aftersaleservice@bertazzoni.com Telephone - Monday through Friday, 7.30am to 7.30pm EST (except US public holidays).