Installation, Service and User Instructions FREESTANDING GAS RANGES BERTAZZONI DIMENSIONS: 36’’ (911 mm)(W) x 25 1/8’’ (640 mm)(D) x36’’ (911 mm)(H) MODELS H366GGVCR H366GGVNE H366GGVVI [M3Y0GTV4D(2 or 5)A] [M3Y0GTV4N(2 or 5)A] [M3Y0GTV4L(2 or 5)A] 310291
IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read these instructions completely and carefully. -Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local and national codes and ordinances. -Please ensure that this product is properly grounded. -The installer should leave these instructions with the consumer who should retain for local inspector's use and for future reference.
WARNING Read this instruction booklet before installing and using the appliance. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting the essential safety and operating characteristics. This appliance has been designed for non-professional, domestic use only.
ATTENTION: A manual valve shall be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or shutting off gas to the appliance WARNING: Do not use aerosol sprays in the vicinity of this appliance while it is in operation Requirements Room ventilation – Location and venting. ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the appropriate national and local standards.
INSTALLATION MANUAL ANTI-TIP STABILlTY DEVICE INSTALLATION INSTRUCTIONS 1. The anti-tip bracket have to be installed to the rear wall as shown. The height for the bracket location from the floor has to be determined after the range legs have been adjusted to the proper installation height - as shown in the installation instructions – and after the range has been leveled. 2. Measure from the floor to the bottom of the anti-tip bracket location on the back of the range. 3.
BACKGUARD INSTALLATION INSTRUCTION It’s always compulsory to installa the riser even for an island installation 1) Remove n°2 screws fixing worktop as shown in fig.1 2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in fig .2 3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.3) 4) Assemble back part with front part of the backguard and fix them with a screws supplied with the backguard kit (fig.
WORKTOP FRONT HANDLE INSTALLATION INSTRUCTIONS In order to increase the clearance between front edge of the worktop and the burners for your safety it is recomended to install the worktop front handle supplied with the appliance.
INSTALLATION SIDE-BY-SIDE TO KITCHEN CABINET 1. This range may be installed directly adjacent to existing 36" (91.5 cm) high cabinets. IMPORTANT: The top border of the worktop should be at the same level of the adjacent cabinet countertop. This can be accomplished by raising the unit using the adjustment spindles on the legs. 2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other vertical surfaces above 36" (91.4 cm) high.
COOKER HOOD INSTALLATION The bottom of the hood should be 25 1/2" (65 cm) min. to 31 1/2" (80 cm) above the countertop. This would typically result in the bottom of the hood being 61 1/2" (156.2 cm) to 67 1/2" (171.5 cm) above the floor. Check for other minimum clearance requirements mandated by specific local or regional installation codes. Refer to the rangehood installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood.
Wiring diagram For freestanding gas range model H366GGV M3Y0GTV4(L,N,D)(2 or 5)A CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. For freestanding gas range model H365GGV M3W0GTV4X(L,N,D)(2 or 5)A CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
GAS CONNECTION All gas connections must be made according to national and local codes. The gas supply (service) line must be the same size or greater than the inlet line of the appliance. This range uses a 1/2" NPT inlet (see fig. in this chapter for details of gas connections installations).On all pipe joints use sealant resistant to LP gas. 1.
PERFORMANCE CHECKLlST All burners are tested before leaving the factory. There are no adjustments for the burners if connected according to the information on the rating plate. Check each burner for proper operations. Flames should be blue in all settings. If service is required, contact your dealer for the name of their authorized service agency. Gas conversions and initial installation are not the responsibility of the manufacturer. The installer should carry out the following performance checks.
- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure: Lift up the burners and unscrew the nozzles ( Fig.) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE shown below. Follow the instructions below to change the oven burner nozzle: 1) Remove the oven level (Fig. 9A-9B).
Models H366GGV [M3Y0GTV4(L,N,D)(2 or 5)A] Adapting to different types of gas Burner Position Auxiliary Front R Semi-Rapid Rear L & C Front C Rear R Rapid Front L Inner Dual Burner Front L Outer Oven Broiler Oven downside Oven upside Injector diam. [mm.] 0,90 0,54 1,18 0,70 1,55 0,92 0,80 0,49 N°2 x 1,15 N°2 x 0,70 2,00 1,15 1,90 1,10 Gas Type NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) Pressure [i.w.c.
Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum: 1) Light the burner and set the knob to the MINIMUM position (small flame). 2) Remove the knob of the valve that is press fit on the rod of that valve.
USER MANUAL WARNINGS: Do not to cover the holes inside the oven with aluminium paper Do not to cover the burners of cooktop with aluminium paper Do not store any flammable objects or objects under pressure in the storage compartment Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquid. Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a safe place in order to avoid potential hazards.
CONTROL PANEL DESCRIPTION On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls that a cooker can have: the symbol shows the disposition of burners on the worktop, the full dot identifies the burner in object (in this case the front burner on the right).
WARNING: check the position of the burner caps before operation. Correct usage of pans: - Dry the bottom of the pan before placing it on the hotplate. - Use pots with a flat, thick bottom, except for wok cooking. - When using the burners, ensure that the handles of the pans are correctly positioned. Keep children away from the appliance. - When cooking foods with oil and fat, which are very flammable, the user should not leave the appliance unattended.
The oven burner can be ignited in different ways: - Manual lighting (it is always possible even when the power is cut off): To light the oven, open the oven door and turn the knob at maximum position . At the same time put a lit match next to the ignition tube that is visible on the oven level . Then press the thermostat knob (this makes the gas start to flow) and keep it pressed, after the burner has been completely lit, for 10 seconds.
To activate the convection fan use the selector placed on control panel. Turn the knob anti clockwise for activation of the convection fan +light Turn the knob clockwise to turn on the oven light.
USING THE GAS BROILER The gas broiler is controlled with the same gas oven knob, but turning it clockwise instead of counterclockwise (see the gas oven use instructions), matching the symbol with the indicator. The broiler burner always operates at maximum and therefore there is no minimum position. In addition, it is equipped with a safety device to prevent the flame from going out.
CLEANING THE APPLIANCE: Never use abrasive cleaners Before cleaning the appliance it should be disconnected from the power supply. Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using warm water. Any spillage must always be removed as soon as possible using a rag. If it become difficult to open or close a valve, do not force it, but immediately request the assistance of the technical service personnel.
H366GGVVI H366GGVCR H366GGVNE SPARE PARTS LIST NUMBER COMPONENT DESCRIPTION 11 202387 BURNERS FLASK 18 202432 PART FOR DUAL WOK AND SEMI RAPID BURNERS 38 306003 THERMOSTAT CLIP 80 504160 COVER FOR SMALL FLAME SPREADER 81 504161 COVER FOR MEDIUM BURNER 82 504162 COVER FOR RAPID BURNER 85 504187 COVER IN FOR DUAL BURNER FLAME SPREADER 86 504186 COVER OUT FOR DUAL BURNER FLAME SPREADER 105 202431 UP SUPPORT FOR AXIAL COOLIN FAN 106 202383 DOWN SUPPORT FOR AXIAL COOLIN FAN 109 202504 INSIDE FLAP DOOR 117 101
917 917 929 930 940 942 943 944 947 947 948 948 965 972 1041 1043 1044 1143 1404 1406 1407 1411 1415 1419 1421 1422 1508 1508 1508 1602 1602 1602 1603 1603 1608 1609 1614 1615 1617 1622 1624 1627 1628 1631 1639 1644 1645 1646 1661 1671 1673 1674 1677 1679 1685 1686 1687 1705 1708 1800 1801 1802 1803 1804 4106 4301 4301 4301 4302 4302 4302 5140 108665 108666 202389 202214 201168 403458 308031 403455 403456 403456 403457 403457 408052 202360 4010047 4010048 4010049 910666 403459 403454 406367 411090 602040 4
