Manualshelf

7441_KTI36XT Installation Drawing.pdf - 0, 89 MB

ManualsBrandsBertazzoni ManualsCooking36'' T-Shape Hood - Island
1
2"
3
⁄8
26"
5
⁄8
35"
3
⁄8
13"
3
⁄4
11"
7
⁄16
PRODUCT DIMENSIONS
MIN INSTALLATION
MAX INSTALLATION
24" - 30"
2"
3
⁄8
35"
3
⁄8
35"
15
⁄16
PRODUCT INSTALLATION
Ø 5"
15
⁄16
min 27"
3
⁄4
- max 39"
10
⁄
16
12"
3
⁄16
INSTALLATION OF WIRING CONNECTION
Remove the cover from the field wiring compartment.
DO NOT turn on the power until installation is complete!
Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire
under the Green grounding screw.
Attach the White lead of the power supply to the White lead of the
rangehood with a twist-on type wire connector.
Attach the Black lead of the power supply to the Black lead of the
rangehood with a twist-on type wire connector.
Replace the field wiring compartment cover and the grease filters.
Hood Clearance
Recommended height above cooking surface:
min 24"
for electric worktop
min 30"
for gas worktop
SIDE VIEW
27"
3
⁄4
26"
5
⁄8
39"
10
⁄
16
max 101"
15
⁄16
for electric worktop - max 107"
15
⁄16
for gas worktop
30"
1
⁄8
42"
min 90"
1
⁄16
for electric worktop - min 96"
1
⁄16
for gas worktop
FIGURE 13
MAKE THE ELECTRICAL CONNECTION
(SEE
FIGURE 11) DO NOT turn on the power until installation is
complete! Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire under the
Green grounding screw. Attach the White lead of the power
supply to the White lead of the rangehood with a twist-on type
wire connector. Attach the Black lead of the power supply
to the Black lead of the rangehood with a twist-on type wire
connector.
1. The UPPER CHIMNEY
COVER (C in FIGURE 13)
attaches to the top of the
support structure using two
screws provided (G in FIGURE
13). If using the High Ceiling
Chimney Kit, use the UPPER
CHIMNEY COVER supplied
with the kit. Slide up and
attach the UPPER CHIMNEY
COVER.
2. Attach the duct work to the
DAMPER (M in FIGURE 1 .)
Make sure to seal all joints with
duct tape to prevent leaks.
3. The LOWER CHIMNEY
COVER (B in FIGURE 13)
attaches using two screws
provided (G in FIGURE 13 .)
Install the LOWER CHIMNEY
COVER by sliding it up over
the support and the UPPER
CHIMNEY COVER.
For ductless installations, line up the DUCTLESS DIVERTER
INSTALLING THE RANGEHOOD
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D.White wires
E. Green (or bare) ground wire from home power supply
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D. White wires
E. Green (or bare) ground wire from home power supply connected to green ground screw
F. Range hood power supply cable
G. Range hood power supply cable connected to green ground screw
2"
3
⁄8
26"
5
⁄8
35"
3
⁄8
13"
3
⁄4
11"
7
⁄16
PRODUCT DIMENSIONS
MIN INSTALLATION
MAX INSTALLATION
24" - 30"
2"
3
⁄8
35"
3
⁄8
35"
15
⁄16
PRODUCT INSTALLATION
Ø 5"
15
⁄16
min 27"
3
⁄4
- max 39"
10
⁄
16
12"
3
⁄16
INSTALLATION OF WIRING CONNECTION
Remove the cover from the field wiring compartment.
DO NOT turn on the power until installation is complete!
Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire
under the Green grounding screw.
Attach the White lead of the power supply to the White lead of the
rangehood with a twist-on type wire connector.
Attach the Black lead of the power supply to the Black lead of the
rangehood with a twist-on type wire connector.
Replace the field wiring compartment cover and the grease filters.
Hood Clearance
Recommended height above cooking surface:
min 24"
for electric worktop
min 30"
for gas worktop
SIDE VIEW
27"
3
⁄4
26"
5
⁄8
39"
10
⁄
16
max 101"
15
⁄16
for electric worktop - max 107"
15
⁄16
for gas worktop
30"
1
⁄8
42"
min 90"
1
⁄16
for electric worktop - min 96"
1
⁄16
for gas worktop
FIGURE 13
MAKE THE ELECTRICAL CONNECTION
(SEE
FIGURE 11) DO NOT turn on the power until installation is
complete! Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire under the
Green grounding screw. Attach the White lead of the power
supply to the White lead of the rangehood with a twist-on type
wire connector. Attach the Black lead of the power supply
to the Black lead of the rangehood with a twist-on type wire
connector.
1. The UPPER CHIMNEY
COVER (C in FIGURE 13)
attaches to the top of the
support structure using two
screws provided (G in FIGURE
13). If using the High Ceiling
Chimney Kit, use the UPPER
CHIMNEY COVER supplied
with the kit. Slide up and
attach the UPPER CHIMNEY
COVER.
2. Attach the duct work to the
DAMPER (M in FIGURE 1 .)
Make sure to seal all joints with
duct tape to prevent leaks.
3. The LOWER CHIMNEY
COVER (B in FIGURE 13)
attaches using two screws
provided (G in FIGURE 13 .)
Install the LOWER CHIMNEY
COVER by sliding it up over
the support and the UPPER
CHIMNEY COVER.
For ductless installations, line up the DUCTLESS DIVERTER
INSTALLING THE RANGEHOOD
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D.White wires
E. Green (or bare) ground wire from home power supply
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D. White wires
E. Green (or bare) ground wire from home power supply connected to green ground screw
F. Range hood power supply cable
G. Range hood power supply cable connected to green ground screw
2"
3
⁄
8
26"
5
⁄
8
35"
3
⁄
8
13"
3
⁄
4
11"
7
⁄
16
PRODUCT DIMENSIONS
MIN INSTALLATION
MAX INSTALLATION
24"
- 30"
2"
3
⁄
8
35"
3
⁄
8
35"
15
⁄16
PRODUCT INSTALLATION
Ø
5"
15
⁄
16
min 27"
3
⁄
4
-
max
39"
10
⁄
16
12"
3
⁄
16
INSTALLATION OF WIRING CONNECTION
Remove the cover from the field wiring compartment.
DO NOT turn on the power until installation is complete!
Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire
under the Green grounding screw.
Attach the White lead of the power supply to the White lead of the
rangehood with a twist-on type wire connector.
Attach the Black lead of the power supply to the Black lead of the
rangehood with a twist-on type wire connector.
Replace the field wiring compartment cover and the grease filters.
Hood Clearance
Recommended height above cooking surface:
min 24"
for electric worktop
min 30"
for gas worktop
SIDE VIEW
27"
3
⁄
4
26"
5
⁄
8
39"
10
⁄
16
max 101"
15
⁄
16
for electric worktop - max 107"
15
⁄
16
for gas worktop
30"
1
⁄
8
42"
min 90"
1
⁄
16
for electric worktop - min 96"
1
⁄
16
for gas worktop
FIGURE 13
MAKE THE ELECTRICAL CONNECTION
(SEE
FIGURE 11) DO NOT turn on the power until installation is
complete! Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire under the
Green grounding screw. Attach the White lead of the power
supply to the White lead of the rangehood with a twist-on type
wire connector. Attach the Black lead of the power supply
to the Black lead of the rangehood with a twist-on type wire
connector.
1. The UPPER CHIMNEY
COVER (C in FIGURE 13)
attaches to the top of the
support structure using two
screws provided (G in FIGURE
13). If using the High Ceiling
Chimney Kit, use the UPPER
CHIMNEY COVER supplied
with the kit. Slide up and
attach the UPPER CHIMNEY
COVER.
2. Attach the duct work to the
DAMPER (M in FIGURE 1 .)
Make sure to seal all joints with
duct tape to prevent leaks.
3. The LOWER CHIMNEY
COVER (B in FIGURE 13)
attaches using two screws
provided (G in FIGURE 13 .)
Install the LOWER CHIMNEY
COVER by sliding it up over
the support and the UPPER
CHIMNEY COVER.
For ductless installations, line up the DUCTLESS DIVERTER
INSTALLING THE RANGEHOOD
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D.White wires
E. Green (or bare) ground wire from home power supply
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D. White wires
E. Green (or bare) ground wire from home power supply connected to green ground screw
F. Range hood power supply cable
G. Range hood power supply cable connected to green ground screw

Summary of content (1 pages)