24” DRAWER MICROWAVE INSTALLATION GUIDE Model MD24X TINSLB075MRR0 1 E
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT – PLEASE READ AND FOLLOW • Before beginning, read these instructions thoroughly and carefully. • WARNING: If the information in this manual is not followed exactly, a fire or electrical shock may result that could cause property damage, personal injury or death. • Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
UNPACKING YOUR DRAWER MICROWAVE CLEARANCES AND DIMENSIONS • Dimensions that are shown in figure 1 must be used. Given dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See figure 4. • Remove all packing materials from inside the Drawer Microwave. DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the top of the appliance. • Contact surface must be solid and level.
DRAWER MICROWAVE MEASUREMENTS A B B C C E D A J F H K G I F G Q J I I L N M D H O E P FIGURE 2 FIGURE 1 A. 21-5/8" (549.28 mm) A. 6" (152.40 mm) B. 4-11/16" (119.06 mm) B. Suggested electrical outlet location* C. 1-3/4" (44.45 mm) C. Anti-Tip block D. 21-7/8" (555.60 mm) D. 5" (127 mm) E. 23-7/8" (606.43 mm) E. 3-1/2" (88.90 mm) F. 15-7/8" (403.22 mm) F. 4" (101.60 mm) G. 14-19/32" (370.69 mm) G. 22-1/8" (561.98 mm) opening H. 1-9/64" (29 mm) door thickness H.
ANTI-TIP BLOCK ELECTRICAL OUTLET The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more protected electrical supply. It is recommended that a separate circuit serving only this appliance be provided. NORMAL INSTALLATION STEPS Anti-Tip Block Installation Instructions • To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed located 14-13/16" above the floor on which the appliance will sit. The 6" Anti-Tip block must be provided by the installer.
MODEL AND SERIAL NUMBER LOCATION DRAWER INSTALLATION The nameplate includes model number and serial number. Open the Drawer Microwave fully. The label is slightly beyond the back wall of the microwave cavity facing up from the flat surface. A CARE, CLEANING AND MAINTENANCE Refer to the Use and Care Manual for cleaning instructions. Mounting Screws PARTS SUPPLIED B BEFORE YOU CALL FOR SERVICE 4 Screws Read the BEFORE YOU CALL and operating instruction sections in your Use and Care Manual.
FOUR À MICRO-ONDES MONTÉ AU DESSUS D’UNE CUISINIÈRE GUIDE D’INSTALLATION Modèle MD24X 1 F
INSTRUCTIONS DE SÛRETÉ IMPORTANTES IMPORTANT - S’IL VOUS PLAÎT LIRE ET SUIVRE • Prière de lire attentivement toutes ces directives avant de commencer. • Le kit comprend des parties métalliques, il faut faire attention lors de la manipulation et de l’installation pour éviter éventuelles blessures.
DÉBALLAGE DU FOUR DRAWER MICROWAVE DÉGAGEMENTS ET DIMENSIONS • Les dimensions indiquées au Schéma 1 doivent être observées. Ces dimensions offrent un dégagement minimal. Repérer la prise électrique dans l’aire ombrée dans le coin gauche supérieur de la découpe. Voir Schéma 4. • Retirez tout le matériau d’emballage du Drawer Microwave. N’ENLEVEZ PAS LE COUVERCLE DU GUIDE D’ONDES, qui se trouve sur le dessus du Four Drawer Microwave. • La surface de contact doit être solide et de niveau.
MESURES POUR LE FOUR DRAWER MICROWAVE A B B C C E D A J F H K G I F G Q J I I L N M D H O E P SCHÉMA 2 SCHÉMA 1 A. 21-5/8 po (549,28 mm) A. 6 po (152,40 mm) B. 4-11/16 po (119,06 mm) B. Emplacement de la prise électrique* C. 1-3/4 po (44,45 mm) C. Bloc antibasculement D. 21-7/8 po (555,60 mm) D. 5 po (127 mm) E. 23-7/8 po (606,43 mm) E. 3-1/2 po (88,90 mm) F. 15-7/8 po (403,22 mm) F. 4 po (101,60 mm) G. 14-19/32 po (370,69 mm) G. Ouverture 22-1/8 po (561,98 mm) H.
BLOC ANTI-BASCULEMENT PRISE DE COURANT ÉTAP ES D’INSTA LLATION NORMA LE Le courant alimentation est 120 volts, 60 Hz, CA seulement, 15 A ou plus et doit être protégé. Il est recommandé d’alimenter cet appareil par un circuit séparé. DIRECTIVES D’INSTALL ATION DU BLOC ANTI-BASCULEMENT Le four est équipé d’une fiche trois broches, mise à la terre. Il faut la brancher dans une prise murale correctement installée et mise à la terre.
EMPLACEMENT DES NUMÉROS DE MODÈLE ET DE SÉRIE INSTALLATION DU TIROIR La plaque d’identification comprend les numéros de série et de modèle. Ouvrir complètement le four Drawer Microwave. L’étiquette se trouve légèrement au-delà de la paroi arrière de la cavité du four à micro-ondes sur la surface plate. A ENTRETIEN, NETTOYAGE ET SERVICE Consulter le mode d’emploi et d’entretien pour les instructions de nettoyage.
F 8
9 F
BERTAZZONI SPA VIA PALAZZINA 8 42016 GUASTALLA RE ITALY WWW.BERTAZZONI.