INSTRUCTIONS FOR THE INSTALLATION, MAINTENANCE AND USE OF FIXED HOBS WITH GAS OR MIXED SUPPLY DIMENSIONS: (605 mm)(W) x (520 mm)(D) (TYPE PM6V) ‘A’ Models PM6030X Models PM6040X (TYPE PM6V) ‘B’ 310733
Read this instruction booklet before installing and using the appliance. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting the essential safety and operating characteristics. This appliance has been designed for non-professional, domestic use only.
DO NOT MODIFY THIS APPLIANCE. Descriptions DESCRIPTIVE CAPTION FOR HOB DESCRIPTION OF HOBS 1. Dual burner 2. Rapid burner 3. Medium burner 4. Small Burner 5. Dual in burner control knob 6. Dual out burner control knob 7. Rapid burner control knob 8. Medium burner control knob 9. Small burner control knob Model ‘A’ Fig. 11 Model ‘B’ Fig.
L7 925 B3 (*) 60 L8 40 B4 (*) 152 L9 172 (*) Note: -B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet. -B2 and B4 are the min. clearance between the left/right side edge of the appliance and the side wall (if present). -B3 is the min. clearance between the back edge of the appliance and the back wall.
CONNECTING THE APPLIANCE TO THE GAS SUPPLY Before connecting the appliance to the gas supply you first need to remove the plastic protective plug for the gas supply which is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew it. Then make sure that the details shown on the label on the lower part of the case are compatible with those of the gas supply.
CAUTION: save the orifices removed from the appliance for future use Regulation of burners Regulation of the "MINIMUM" on the burners To regulate the minimum on the burners carry out the following procedure indicated below: 1) Turn on the burner and put the knob onto position MINIMUM ( small flame ). 2) Remove the knob ( Fig. 10) of the tap which is set for standard pressure. The knob is found on the bar of the tap itself.
BEFORE LEAVING When the installation is complete, always check for gas leaks using a soapy solution. Never use a flame to make this check. Ignite all burners on high flame to ensure correct operation of gas valves, burners and ignition. Turn gas taps to low flame position and observe each burner to ensure they ignite completely at all ports and that the flame is stable. Conduct these checks for each burner individually and concurrently.
Tips for using burners correctly: WARNING: During use of each gas burner(s) adjust the burner flame size properly so it does not extend beyond the edge of the cooking utensil. This is an instruction based on safety considerations - Use suitable pots for each burner (see Fig. 14 and Table B) - When the liquid is boiling, turn down the knob to the MINIMUM position. - Always use pots with a cover.
Cleaning the burner caps: Lift the burner caps from the burner heads and wash them in soapy water and dry thoroughly. Before replacement on the burner head ensure that the holes are not clogged. SERVICE & MAINTENANCE INSTRUCTIONS Service and maintenance only to be carried out by an authorised person Routine maintenance Have the condition and efficiency of the gas pipe and the pressure regulator (if installed) checked periodically.
After-sales technical service and spare parts Before leaving the factory, this appliance was tested and adjusted by specialist skilled staff to give the best operating results. Any subsequent necessary repairs or adjustments must be carried out with the greatest care and attention by authorised personnel. For this reason, we strongly advise you contact the Bertazzoni Service Center, specifying the nature of the problem, the model of the equipment and the serial number.
Fig 1 Fig 2 Fig.3 Fig. 3A Fig.
Fig.4 Fig.5A Fig.6 Fig.7 Fig.8 Fig.9 Fig.5B Fig.
Fig.11 Fig.13 Fig.12 Fig.14 Fig.
Fig.
