Installation Sheet

8
3.1 Transport to installation site
and unpacking
The appliance is very heavy.
Take maximum care during handling
to avoid injury.
The appliance should always be
transported in an erect position.
Avoid at all costs leaning it on its front
side.
Since this is a large and heavy appliance, before trans-
porting the appliance, check the access to the loca-
tion where it will be installed (door size, manoeuvring
space in stairwells, etc.).
The appliance is attached to the base of the packaging
(pallet) through four bolts which can be removed us-
ing a 19 mm (3/4”) wrench.
It is recommended to use a manual transporting de-
vice to move the appliance to the installation site, and
only at this point to remove the base of the packaging.
The appliance should always be transported in an
erect position.
If this is not possible, transport the appliance laying
on its rear side.
Once at the installation site, the appliance, which is
equipped with four wheels, can be taken o the pallet
and positioned in the installation area.
Operate as follows:
> Take o the four boltshsecuring [ 1 ] the appliance to
the pallet by means of a 19 mm (3/4”) wrench or socket.
> Remove the fixing brackets [ 3 ] and [ 4 ] .
> To release the front fixing bracket [ 3 ] , unscrew the
rear wheel adjusting bolt [ 2 ] by means of a 13 mm
(1/2”) wrench or socket. Avoid straining this bolt at its
stop points one way or the other so as to not damage
the rear leveling system.
Ensure the front leveling legs are retracted so that all
4 wheels are able to contact the floor for easiest ma-
neuvering.
> From the back of the unit and by means of a suit-
able, high duty hand trolley, take o the appliance and
place it on the floor.
Be very careful to avoid any damage to floors. Delicate
floors should be protected with plywood, hard card-
board or similar material panels.
3. PREPARING THE INSTALLATION
3.2 Electrical and water connection
The Built-in filter cannot make it safe to
drink any water which is not suitable for
human consumption.
The appliance should be connected only
to a potable water supply system.
Do not use extension cords or adapters.
Once the appliance is fully installed, con-
nected to the water supply (if applicable)
and operational, in the event that the wa-
ter supply must be turned off, (touch the
button
Ice Maker
Water Filter
Water System Purge
on control panel to disable the
ice maker) before the main water is shut
off to prevent the appliance from entering
a ‘NO WATER IN’ alarm state.
The appliances are delivered from the factory for op-
eration at 110V-120V AC - 60Hz (US and Canada).
They are provided with a suitable supply cable and
plug to be connected to an appropriate 15A socket
providing an eective grounding.
A dedicated 15A circuit breaker should also be in-
stalled and should be easily accessible so that it can
be easily switched o before performing any installa-
tion or maintenance.
To connect to the water supply system (for appliances
equipped with ice makers) a 1/4” waterline with ac-
cessible shut-o valve must be supplied.
The appliance is provided with a water adapter elbow
which is suitable for the recommended water pres-
sure and complies the applicable food and water reg-
ulations..
The water filter cartridge, which is provided with the
appliance, should be installed according to the ac-
companying instructions. The solenoid connection on
the appliance is 3/4” diameter but is metric threaded
(NPT). A standard garden hose threaded connector
such as a braided stainless hose found at typical hard-
E
E
E
E
E
W
W
W
W
W
E
W
1
4
1
2
3
EW
E W
EW
E W
ELECTICAL & WATER
CONNECTION