REARWARD- & FORWARD-FACING USER MANUAL ECE R44 04 GROUP WEIGHT AGE 0+/1 0-18 kg 6m-4y 1
Thank you for choosing BeSafe iZi Combi. BeSafe has developed this seat with much care, to protect your child during the next phase of her or his life. It is important that you read this user manual BEFORE installing your seat. Incorrect installation could endanger your child.
Preparing to install Crucial parts Floor support Release handle head rest Belt clamp (2x) Adjustable head rest Harness shoulder straps Harness buckle Central adjuster Reclining lever Front brace Belt guiding hook Ratchet for front brace Belt guiding horns (2x) Rearward-facing in the back or front seat: preparation It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG.
- The floor support must go through the belt loop. The belt loop must also be led into the hook on the floor support (2). 5- Do not fasten the locking bolt yet. (2) Second alternative: using the rails of the front seat a- Secure an anchor belt round each of the rails of the front seat of the vehicle by bringing the locking device of the anchor belt through the belt loop. Pull tight (5). (5) b- Cross the anchor belts under the front seat of the vehicle.
Rearward-facing in the back seat: installation Fourth alternative: using the front seat a- Join the 2 anchor belts together to make a single belt. Put the lock of belt 1 through the loop of the belt 2 and then through the loop of belt 1. Pull it firmly (7). b- Put the middle part of the anchor belt over the inner part of the vehicle seat. Cross the two ends of the anchor belt under the front seat of the vehicle and bring them upwards to the seat (8).
20- Connect the anchor belts with the child seat. The anchor belts must be crossed over. 15- Pull out the shoulder belt and make it into a loop (10a). 16- Thread the loop through the metal part of the red belt block (10b). 21- Tighten the anchor belts to their maximum (13). 17- Guide the loop into the red slit (10c). 22- Lock the floor support with the locking bolt (14). 18- Tighten the belt by pulling the top part down (10d).
Rearward-facing in the front seat: installation With the anchor belts in place the installation can continue: 7- Place the seat sideways into the car with the front brace towards you. 12- Position the 3 point car belt. Place the hip belt over the base of the seat behind the belt guiding horns on each side. Fasten the car belt, click (16). Tension the shoulder belt. (16) 8- Turn the seat into the right position (with the front brace against the back rest).
17- Move the front brace outwards with the ratchet. Continue tightening until the brace is pressed well into the back rest of the vehicle seat (19). (19) 18- Connect the anchor belts with the child seat. The anchor belts must be crossed over. 19- Tighten the anchor belts to their maximum (20). 20- Lock the floor support with the locking bolt (21). (20) (21) Forward-facing belt installation It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG.
Positioning of the child 8- Put the shoulder belt through the belt clamps. Make sure the belt is not twisted (25). 9- Push the seat firmly into the car seat. C 10- Tight installation is most important for forward facing seats. Tension the belts as follows: Pull the shoulder belt upwards (A). Have a firm grip on the shoulder belt in the seat area (B). Close the clamp on the inner side (C). Pull upper belt part on the door side and close clamp D (25).
5- Position the shoulder straps over the orange marking at sides of the seat to keep the harness open while you position the child (30). (30) Removing and refitting the cover • There are 2 versions of the fabric cover. If there are velcro squares (see green arrow (34/35)), follow the steps of alternative 1. If there are no velcro squares go to alternative 2. (34) (35) 6- When the child is positioned, place the shoulder straps over the child’s shoulders and close the buckle: CLICK! (31).
Removing the cover: alternative 2 1- Pay attention when you remove the cover, as fitting the cover is done in the opposite way. Cleaning instructions • The cover of the seat must be washed according to the instructions on the inside of the cover (38). (37) 2- To remove the seat cover, the harness straps must be released at both sides. See red circle. Start to take off the lower seat part and unhook both harness straps from the metal belt hooks (37).
! Important advice Point of sale information • DO NOT attempt to dismantle, modify or add any part to the seat. Warranty will expire if non-original parts or accessories are used. • DO NOT use anything, such as a cushion, to raise the child seat off the passenger seat of the vehicle. In an accident the seat will not be able to protect your child in the right way. • Never leave your child unattended in the seat. • Make sure all passengers are informed about how to release your child in case of emergency.
semi-universal 0-18 kg universal 9-18 kg E5 04204 E5 04205 HTS BeSafe as N-3535 Krøderen, Norway - www.besafe.eu 24 B904-8010-B N2001030 Guarantee • All BeSafe products are carefully designed, manufactured and tested. All of our BeSafe child seats are tested periodically out of our continuous production in our test laboratory. Furthermore they are tested by independent test institutes.