26 1 34 27 35 16 2 4 3 5 USER MANUAL 6 7 8 28 29 12 9 13 10 11 14 15 36 31 17 19 Rearward- & forward-facing 20 21 23 Group 0+ - 1 18 Weight 0-18 kg Age 6m - 4y 37 30 ECE R44 04 24 38 22 25 32 33 39
40 47 41 49 52 54 Thank you for choosing BeSafe iZi Combi ISOfix 60 BeSafe has developed this seat with great care, to protect your child during the first phase of his or her life. D C • The harness straps must always be locked when the child is in the seat. • The harness straps must be tightened without slack and not twisted. • The seat cover contains magnets in the areas with the orange indications. Magnets can influence electronic equipment such as pacemakers.
Rearward-facing: ISOfix installation • Make sure you can fit no more than one finger between the harness and your baby (1 cm). • If in doubt, consult either the car seat manufacturer or the retailer. Preparing to install Crucial parts 1. Adjustable head rest 2. Shoulder straps (2x) 3. Harness buckle 4. Body hugger 5. Front brace 6. Central adjuster 7. Reclining lever 8. Belt guiding hook 9. Ratchet for front brace 10. Cap ISOfix connector (2x) 11. Switch for ISOfix connectors (2x) 12. Wedge 13.
Removing the seat 17. Click the ISOfix connectors in the ISOfix anchorage of the vehicle. (32) 18. Remove the installation clips. 19. Make sure that all indicators on both sides are green. (33) 20. Push the seat towards the backrest of vehicle seat till the frontbrace touches the backrest; the isofix arms slide in and will click into a new position. (34) 21. Move the front brace outwards with the ratchet. Continue tightening until the brace is pressed well into the back rest of the vehicle seat. (35) 22.
Forward-facing belt installation 1. When mounting in the back seat of the vehicle, push the front seat of the vehicle forward as much as possible. 2. When mounting in the front seat of the vehicle, adjust the back rest in an upright position. 3. Install the wedge on the bottom of the seat; position the hooks in the hole. (42) Rotate the wedge until you hear click. (43, 44) 4. Install the seat in forward facing position without front brace and the floor support in folded up position. 5.
Positioning the child 1. Position of the shoulder straps: Check that the shoulder strap slots are level with your child’s shoulders. • too high (52) • correct (53) 2. The height of the shoulder straps and the head rest can be adjusted by pulling the release handle upwards at the back of the head rest and pulling the head rest up or down while keeping the head rest upright. (54) 3. Pull the shoulder straps up while pressing the button of the central adjuster. (55) 4. Open the harness buckle. 5.
!! Warning: potential misuse Rearfacing • It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG. • DO NOT use the seat without floor support. • DO NOT use the seat without tightening the front brace. • Make sure the indicators are green before you drive. Forward-facing • DO NOT install the seat forward facing without using the wedge. • Install only with 3-point car belts, approved to UN/ECE Regulation No. 16 or other equivalent standards.
Guarantee • All BeSafe products are carefully designed, manufactured and tested. All of our BeSafe child seats are tested periodically out of our continuous production in our test laboratory. Furthermore they are tested by independent test institutes. • Should this product prove faulty within 24 months of purchase due to materials or manufacturing fault, except covers and harness straps, please return it to the original place of purchase.
B1301-8013 N2002500